2010 ASTON MARTIN V8 VANTAGE instrument panel

Instrument Panel (IP) (01.12)
Body System (01.00)1-9-22 Workshop Manual Issue 5, January 2010
15. Remove the two screws that attach the right side cover panel for the centre console to the body.
C-01-12-DA-32
16. Remove the two nuts that attach the right side cover panel for the centre console to the body.
C-01-12-DA-33
17. Remove the right side cover panel for the centre console.
C-01-12-DA-34
18. Remove the four Torx screws and the four nuts that attach the stowage compartment cover to the body.
C-01-12-DA-35
19. Remove the stowage compartment cover.
C-01-12-DA-36
20. Remove the screw that attaches the stowage compartment to the body.
C-01-12-DA-37

Instrument Panel (IP) (01.12)
Body System (01.00)
Issue 5, January 2010 Workshop Manual 1-9-23
21. Remove the four Torx screws that attach the stowage compartment to the body.
C-01-12-DA-38
22. Remove the two screws that attach the stowage compartment to the body.
C-01-12-DA-39
23. Remove the rubber mat from the cup holder.
C-01-12-DA-05
24. Remove the two Torx screws that attach the armrest to the bracket.
C-01-12-DA-06
25. Remove the leather insert.
C-01-12-DA-07
26. Remove the two Torx screws that attach the armrest to the body.
C-01-12-DA-08
Note: The bracket an d washers will fall from the armrest in
the step that follows.

Instrument Panel (IP) (01.12)
Body System (01.00)1-9-24 Workshop Manual Issue 5, January 2010
27. Move the stowage box and remove the armrest.
C-01-12-DA-40
28. Remove the two screws that attach the centre console panel to the body.
C-01-12-DA-13
29. Push the gear knob down and turn it counterclockwise.
C-01-12-DA-14
30. Remove the gear knob. 31. Release the centre console panel from the body.
C-01-12-DA-17
32. Disconnect the electrical
connector from each of the
four switches.
C-01-12-DA-18
33. Remove the centre console panel.
Install
1. Connect the four electrical connector to each of the four switches (refer to Figure C-01-12-DA-18).
2. Put the centre console panel into position.
C-01-12-DA-19
3. Install the centre console panel.
4. Install the gearknob.

Instrument Panel (IP) (01.12)
Body System (01.00)
Issue 5, January 2010 Workshop Manual 1-9-25
5. Push the gearknob down and turn it clockwise.
C-01-12-DA-15
6. Install and tighten the two screws that attach the centre console panel to the body.
C-01-12-DA-13
7. Install but do not tighten, the two Torx screws, washers and bracket to the armrest.
E-01-12-DA-08
8. Move the stowage box and install the armrest.
C-01-12-DA-40
9. Tighten the two Torx scrws th at attach the armrest to the
bracket.
C-01-12-DA-06
10. Install and tighten the two Torx screws that attach the armrest to the body.
C-01-12-DA-08

Instrument Panel (IP) (01.12)
Body System (01.00)1-9-26 Workshop Manual Issue 5, January 2010
11. Install the leather insert.
C-01-12-DA-07
12. Install the rubber mat into the cupholder.
C-01-12-DA-05
13. Install and tighten the two screws that attach the stowage compartment to the body.
C-01-12-DA-39
14. Install and tighten the four Torx screws that attach the stowage compartment to the body.
C-01-12-DA-38
15. Install and tighten the screw that attaches the stowage compartment to the body.
C-01-12-DA-37
16. Install the stowage compartment cover.
C-01-12-DA-36

Instrument Panel (IP) (01.12)
Body System (01.00)
Issue 5, January 2010 Workshop Manual 1-9-27
17. Install and tighten the four Torx screws and the four nuts that attach the stowage compartment cover to the body.
C-01-12-DA-35
18. Install the right side cover panel for the centre console.
C-01-12-DA-34
19. Install and tighten the two nuts that attach the right side cover panel for the centre console to the body.
C-01-12-DA-33
20. Install and tighten the two screws that attach the right side cover panel for the centre console to the body.
C-01-12-DA-32
21. Install the right side rear bulkhead cover.
C-01-12-DA-31
22. Install and tighten the screw that attaches the right side rear bulkhead cover to the body.
C-01-12-DA-30

Instrument Panel (IP) (01.12)
Body System (01.00)1-9-28 Workshop Manual Issue 5, January 2010
23. Install the right hand side infill panel.
C-01-12-DA-29
24. Install the left side cover panel for the centre console.
C-01-12-DA-28
25. Install and tighten the two nuts that attach the left side
cover panel for the centre console to the body.
C-01-12-DA-27
26. Install and tighten the two sc rews that attach the left side
cover panel for the centre console to the body.
C-01-12-DA-26
27. Install the stowage box cover and the rubber mat.
C-01-12-DA-25
28. Install the left side rear bulkhead cover.
C-01-12-DA-23

Instrument Panel (IP) (01.12)
Body System (01.00)
Issue 5, January 2010 Workshop Manual 1-9-29
29. Install and tighten the screw that attaches the left side rear bulkhead cover to the body.
C-01-12-DA-22
30. Install the left side infill panel.
C-01-12-DA-24
31. Remove the special tool from the operating ram on the tonneau cover.
C-01-12-DA-21
32. Fully close the tonneau cover.
33. Connect the battery.
34. Operate the front seats to their initial positions.
RH/LH Lower Quarter Panel Assembly -
Renew (Roadster Only)
Removal
1. Remove wind deflector (see Workshop Manual procedure 01.17.DA Wind Deflector - Renew).
2. Remove panel centre (see Workshop Manual procedure 01.05.FR/01.05.FS Panel Assembly - Centre - Rear
Bulkhead - LH/RH - Renew).
3. Remove speaker grille (see Workshop Manual procedure 01.05.CP/01.05.CN Grille - Speaker Rear
Quarter - LH/RH - Renew).
4. Remove screw (x1) securing quarter trim to body (under
speaker grille) (see Figure 1).
Repair Operation Time (ROT)