2010 ASTON MARTIN V8 VANTAGE wheel bolt torque

Power Conversion (03.11)
Engine (03.00)
May 2007 Workshop Manual 3-11-1
Engine (03.00)
Power Conversion (03.11)
Maintenance
Connecting Rod Bearing-Renew (Engine
Set)
Removal
1. Remove engine oil sump (see Workshop Manual
procedure 03.02.BN Pan - Oil Sump - Remove and Re-
seal).
2. Remove spark plugs (see Workshop Manual procedure 03.07.DB Spark Plugs - Engine Set - Renew).
3. Remove bolts (x8) securing windage tray to engine bedplate, remove windage tray.
4. Mark bearing caps and connecting rods for correct installation.
5. Rotate crankshaft clockwise to access number 1 cylinder connecting rod bolts.
6. Remove bolts securing bearing cap to connecting rod, remove bearing cap (see Figure 1).
Figure 1
7. Install special tools (303-535) to the connecting rod to prevent damage to crankshaft journal.
8. Move connecting rod upwards, remove bearing shell.
9. Record colour code on bearing shell edge. 10. Remove and discard bearing shell from cap.
11. Record colour code on bearing shell edge, discard
bearing shell.
12. Wipe crankshaft journal, connecting rod and bearing cap using a lint free cloth.
13. Inspect crankshaft journal for damage.
14. Check crankshaft journal for ovality using a micrometer and record journal diameters.
Installation
1. Select the correct colour coded bearing shells for each connecting rod crankshaft journal.
2. Install new selective bearing shell in connecting rod.
3. Lubricate crankshaft journal with clean engine oil.
4. Install connecting rod on crankshaft journal.
5. Remove special tools (303-535) from connecting rod.
6. Install new selective bearing shell in bearing cap.
7. Install bearing cap and new bolts (x2), torque tighten bearing cap bolts.
8. Repeat procedure for remaining connecting rod bearings.
9. Install windage tray to engine bedplate, install and torque tighten bolts (x8).
10. Install spark plugs (see Workshop Manual procedure 03.07.DB Spark Plugs - Engine Set - Renew).
11. Install engine oil sump (see Workshop Manual
procedure 03.02.BN Pan - Oil Sump - Remove and re-
seal).
Crankshaft Main Bearing-Renew (Engine
Set)
Removal
1. Remove bolts (x2), inspection cover to lower crankcase, remove cover.
2. Install tool (303-1185) to restrain flywheel, install and tighten bolts (x2).
3. Remove bolts (x6), clutch cover to flywheel.
4. Release clutch cover from dowels (x3), remove clutch cover, collect drive plate.
5. Remove and discard bolts (x8), flywheel to crankshaft flange.
6. Remove bolts (x2), collect tool (303-1185).
Repair Operation Time (ROT)
WA R N I N G
DO NOT GET USED ENGINE OIL ON YOUR SKIN. USED ENGINE OIL CAN BE HARMFUL.
Caution
Pistons, connecting rods an d connecting rod bearings
should be numbered to make sure they are reassembled
in the same position.
Caution
Connecting rod bolts are tor qu
e tightened to yield and
mu st be replaced.
A0311314
Note: Connecting rod bearings ar e a selective fit by colour
code on edge of bearing shell.
Caution
When assembling connecting rods and connecting rod
bearing caps it is imperative that bearing slots and tangs
be located on the same side of the connecting rods.
Repair Operation Time (ROT)

Power Conversion (03.11)
Engine (03.00)3-11-4 Workshop Manual May 2007
10. Install crankshaft retaining caps (303-534), install and
lightly tighten bolts (x10) (see Figure 8).
Figure 8
11. Install connecting rod bearing caps (x8), install and torque tighten retaining bolts.
12. Remove bolts securing crankshaft retaining caps (303- 534), remove retaining caps (see Figure 9).
Figure 9
13. Apply a 2mm diameter continuous bead of sealant to cylinder block flange ensuring that there are no gaps in
the sealant.
14. Install engine bedplate to cylinder block, install and torque tighten bolts (x34) in the correct sequence.
15. Remove excess sealant from crankshaft rear oil seal
aperture and front face of cylinder block.
16. Clean windage tray.
17. Install windage tray, install and torque tighten bolts (x8). 18. Ensure that oil seal protector is positioned correctly and
install oil seal onto crankshaft flange.
19. Install tool (303-1189) to crankshaft, position nuts on tool against oil seal.
20. Ensure that oil seal and special are parallel to rear of engine.
21. To install oil seal, tighten nuts alternately on tool (303- 1189) until oil seal correctly seated.
22. Remove special tool from crankshaft.
23. Check that the oil se al is located correctly.
24. Clean flywheel and mating face on crankshaft.
25. Install flywheel, align to dowel on crankshaft flange.
26. Install new bolts (x8), install tool (303-1185) to restrain flywheel. Torque tighten bolts (x8) in the correct
sequence.
27. Clean clutch cover and drive plate.
28. Install clutch assembly on flywheel, align to dowels (x3).
29. Install bolts (x6), install clutch alignment tool, evenly torque tighten bolts (x6) in a diagonal sequence.
Remove clutch alignment tool.
30. Remove bolts (x2), collect tool (303-1185).
31. Install inspection cover, install and torque tighten bolts (x2).
32. Install engine sump (see Workshop Manual procedure 03.02.CN Pan - Oil Sump - Remove and Reseal With
Engine Removed).
Crankshaft Assembly-Renew
Removal
1. Remove bolts (x2), inspection cover to lower crankcase, remove cover.
2. Install tool (303-1185) to restrain flywheel, install and tighten bolts (x2).
3. Remove bolts (x6), clutch cover to flywheel.
4. Release clutch cover from dowels (x3), remove clutch cover, collect drive plate.
5. Remove and discard bolts (x8), flywheel to crankshaft flange.
6. Remove bolts (x2), collect tool (303-1185).
7. Release flywheel from dowel, remove flywheel.
8 . R e m o v e e n g i n e s u mp ( s e e Wo r k s h o p M a n u a l p ro c e d u re 03.02.CN Pan - Oil Sump - Remove and Reseal With
Engine Removed).
Caution
Do not lubricate engine bedplate retaining bolts.
Caution
Tighten engine bedplate retaining bolts in the sequence shown.
Caution
Do not rotate crankshaft until all engine bedplate
retaining bolts are tightened to specification.
Caution
Engine bedplate retaining bolts must be tightened
within twenty minutes of applying sealant.
A0311328
A0311328
Caution
Do not use any lubricant on cr ankshaft oil seals or seal
protectors. Make sure all co mponents are clean and dry.
Repair Operation Time (ROT)
ItemCode
Crankshaft Assembly-Renew 03.11.CF
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN.
USED ENGINE OIL CAN BE HARMFUL.

Power Conversion (03.11)
Engine (03.00)
May 2007 Workshop Manual 3-11-7
27. Clean flywheel and mating face on crankshaft.
28. Install flywheel, align to dowel on crankshaft flange.
29. Install new bolts (x8), install tool (303-1185) to restrain
flywheel. Torque tighten bolts (x8) in the correct
sequence.
30. Clean clutch cover and drive plate.
31. Install clutch assembly on fl ywheel, align to dowels (x3).
32. Install bolts (x6), install clutch alignment tool, evenly torque tighten bolts (x6) in a diagonal sequence.
Remove clutch alignment tool.
33. Remove bolts (x2), collect tool (303-1185).
34. Install inspection cover, install and torque tighten bolts (x2).
35. Install engine sump (see Workshop Manual procedure 03.02.CN Pan - Oil Sump - Remove and Reseal With
Engine Removed).
Piston-Renew (Engine Set)
Removal
1. Remove cylinder head gaskets - engine set (see Workshop Manual procedure 03.01.HW Gasket -
Cylinder Head - Engine Set - Renew With Engine
Removed).
2. Remove crankshaft timing sprocket from crankshaft.
3. Install guide pin through lower hole on chain tensioner.
4. Remove bolt securing oil pr essure pump chain tensioner
assembly to engine bedplate (see Figure 1).
Figure 1
5. Remove tensioner assembly (see Figure 2). 6. Remove bolts (x3) securing oil pressure pump to sump
(see Figure 3).
Figure 3
7. Release chain from oil pressure pump sprocket, remove oil pump.
8. Remove and discard oil pressure pump gasket.
9. Remove bolts (x3) securing oil scavenge pump to sump
(see Figure 4).
Figure 4
10. Release chain from oil scavenge pump sprocket, remove scavenge pump.
Repair Operation Time (ROT)
WA R N I N G
DO NOT GET USED ENGINE OIL ON YOUR SKIN.
USED ENGINE OIL CAN BE HARMFUL.
A0302274
A0302274A
A0302274B

Power Conversion (03.11)
Engine (03.00)3-11-28 Workshop Manual May 2007
2. Remove bolts (x2) securing bearing cap to connecting
rod, remove bearing cap (see Figure 2).
Figure 2
3. Install special tools (303-535) to the connecting rod to prevent damage to crankshaft journal.
4. Carefully push connecting rod/piston assembly upwards and remove from cylinder bore.
5. Remove special tools from connecting rod.
6. Install bearing cap on connecting rod, install and lightly tighten retaining bolts.
Installation
1. Clean cylinder bore.
2. Install piston rings in cylinder bore to a pre-determined depth and measure ring gaps.
3. Remove piston ring set from cylinder bore and install on piston.
4. Clean connecting rod.
5. Correctly position ring gaps on piston prior to installation.
6. Remove connecting rod bearing cap.
7. Install bearings in connecting rod and bearing cap.
8. Lubricate cylinder bore, pi ston and rings with clean
engine oil.
9. Install special tools (303-535) to the connecting rod to prevent damage to crankshaft journal. 10. Install piston ring clamp to piston, install piston assembly
in its cylinder bore. Remove piston ring clamp (see
Figure 3).
Figure 3
11. Lubricate crankshaft jour nal with clean engine oil.
12. Carefully pull connecting rod into place on crankshaft journal.
13. Install bearing cap to connecting rod. Install and torque tighten retaining bolts (x2).
Connecting Rod-Renew (Engine Set)
Removal
1. Remove cylinder head gaskets - engine set (see Workshop Manual procedure 03.01.HW Gasket -
Cylinder Head - Engine Set - Renew With Engine
Removed).
2. Remove crankshaft timing sprocket from crankshaft.
3. Install guide pin through lower hole on chain tensioner.
4. Remove bolt securing oil pressure pump chain tensioner assembly to engine bedplate (see Figure 1).
Figure 1
5. Remove tensioner assembly.
Caution
When using a 'two post' vehicle ramp, remove the
screws that secure the rear section of the wheel arch
liner to body. Hold back the rear section of the wheel
arch liner to correctly position the foot of the vehicle lift.
Caution
Make sure the piston ring gaps are positioned at
different positions opposite th e thrust side of the piston
before installation.
A0311314
Repair Operation Time (ROT)
ItemCode
Connecting Rod-Renew 03.11.CN
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN.
USED ENGINE OIL CAN BE HARMFUL.
A0311337
A0302274

Power Conversion (03.11)
Engine (03.00)3-11-34 Workshop Manual May 2007
30. Clean oil scavenge pump and mating face on sump.
31. Install oil pump(s) drive sprocket.
32. Install new oil scavenge pump gasket, align on dowels
(x2).
33. Install chain onto oil scavenge pump sprocket.
34. Install oil scavenge pump, align to dowels (x2), Install and torque tighten bolts (x3).
35. Install chain onto oil pump drive sprocket.
36. Clean oil pressure pump and mating face on sump.
37. Install new gasket to sump, align to dowels (x2).
38. Position oil pressure pump, install chain on pump sprocket.
39. Install oil pressure pump, alig n to dowels (x2), Install and
torque tighten bolts (x3).
40. Install chain tensioner, install and torque tighten bolt, remove guide pin.
41. Install crankshaft timing sprocket.
42. Install cylinder head gaskets - engine set (see Workshop Manual procedure 03.01.HW Gasket - Cylinder Head -
Engine Set - Renew With Engine Removed).
Crankshaft Damper Pulley Assembly-
Renew
Removal
1. Remove engine drive belt (see Workshop Manual procedure 03.05.AB Belt - Engine Drive - Renew).
2. Raise vehicle on ramp.
3. Remove bolts (x2), inspection cover to lower crankcase, remove cover.
4. Install tool (303-1185) to restrain flywheel, install and tighten bolts (x2).
5. Install thrust button of tool (303 -1186) in crankshaft,
position tool in pulley, secure with bolts (x2). Tighten
centre bolt, withdraw pu lley from crankshaft.
6. Collect crankshaft pulley, locking ring and special tool thrust button.
7. Remove special tool from pulley. 8. Remove and discard O-ring seal from pulley (see
Figure 1).
Figure 1
Installation
1. Clean crankshaft pulley, locking ring and mating face on
crankshaft.
2. Lubricate and install new O-ring seal in crankshaft pulley.
3. Install crankshaft pulley, locking ring and new pulley bolt.
4. Torque tighten crankshaft pulley bolt. Remove special tool (303-1185) from crankcase.
5. Install inspection cover to lower crankcase, install and tighten bolts (x2).
6. Lower vehicle on ramp.
7. Install engine drive belt (see Workshop Manual procedure 03.05.AB Belt - Engine Drive - Renew).
Crankshaft Front Oil Seal-Renew
Removal
1. Battery isolation switch ‘OFF’.
2. Raise vehicle on ramp.
3. Remove crankshaft pulley (see Workshop Manual procedure 03.11.CP Pulley Assembly - Crankshaft
Damper - Renew).
Repair Operation Time (ROT)
Caution
The bolt thread in the cran kshaft must be cleaned out
before a new crankshaft pulley retaining bolt is installed
Repair Operation Time (ROT)
ItemCode
Crankshaft Front Oi l Seal-Renew 03.11.CQ
A0311321

Power Conversion (03.11)
Engine (03.00)3-11-36 Workshop Manual May 2007
4. Ensure that oil seal and special are parallel to rear of
engine.
5. To install oil seal, tighten nuts alternately on tool (303- 1189) until oil seal correctly seated.
6. Remove special tool from crankshaft.
7. Check that the oil seal is located correctly.
8. Install clutch and flywheel assembly (see Workshop Manual procedure 08.00.AA Clutch and Flywheel
Assembly - Renew).
Cylinder Block-Renew
Removal
1. Remove cylinder head gasket - engine set (see Workshop Manual procedure 03.01.HW Gasket -
Cylinder Head - Engine Set - Renew With Engine
Removed).
2. Remove crankshaft assembly.
3. Remove pistons and connecting rod assemblies from cylinder block.
4. Remove Torx screws (x4) securing engine oil cooling
valves to cylinder block.
5. Remove engine oil cooling valves (x4).
6. Remove bolts (x5) securing water pump to cylinder block. Remove water pump, discard gasket.
7. Remove cylinder block valley cover.
Installation
1. Clean cylinder block valley cover and mating face on cylinder block.
2. Install cylinder block valley cover.
3. Clean engine oil cooling valves.
4. Install engine oil cooling valves in cylinder block.
5. Install and torque tighten Torx screws (x4).
6. Clean connecting rods and piston assemblies.
7. Correctly position ring gaps on pistons prior to installation.
8. Remove connecting rod bearing caps.
9. Install bearings in connecting rods and bearing caps.
10. Lubricate cylinder bores, pistons and rings with clean engine oil.
11. Install special tools (303-535) to the connecting rod to prevent damage to crankshaft journal.
12. Install crankshaft assembly.
13. Install new gasket, water pump, install and torque tighten bolts (x5). 14. Install cylinder head gasket - engine set (see Workshop
Manual procedure 03.01.HW Gasket - Cylinder Head -
Engine Set - Renew Wi th Engine Removed).
Crankshaft Damper Pulley Assembly-
Renew (with Engine Removed)
Removal
1. Remove engine assembly (see Workshop Manual
procedure 03.00.AA Engine Assembly - Renew).
2. Release drive belt tensioner, release drive belt from idler pulley (see Figure 1).
Figure 1
3. Remove bolt securing drive belt tensioner to engine timing cover, remove tensioner.
4. Remove drive belt from pulleys.
5. Remove bolts (x2), inspection cover to lower crankcase, remove cover.
6. Install tool (303-1185) to restrain flywheel, install and tighten bolts (x2).
7. Install thrust button of tool (303 -1186) in crankshaft,
position tool in pulley, secure with bolts (x2). Tighten
centre bolt, withdraw pulley from crankshaft.
8. Collect crankshaft pulley, locking ring and special tool thrust button.
9. Remove special tool from pulley.
Caution
Alternate nut tightening to correctly seat the crankshaft rear oil seal.
Repair Operation Time (ROT)
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN.
USED ENGINE OIL CAN BE HARMFUL.
Repair Operation Time (ROT)
ItemCode
Crankshaft Damper Pulley Assembly-
Renew 03.11.DP
A030553

Power Conversion (03.11)
Engine (03.00)3-11-38 Workshop Manual May 2007
3. Position new oil seal (fitted dry). Install oil seal in timing
cover using tool (303-750) (see Figure 3).
Figure 3
4. Remove crankshaft oil seal protector.
5. Install crankshaft pulle y (see Workshop Manual
procedure 03.11.DP Pulley Assembly - Crankshaft
Damper - Renew With Engine Removed).
Crankshaft Rear Oil Seal-Renew (with
Engine Removed
)
Removal
1. Remove engine assembly (see Workshop Manual
procedure 03.00.AA Engi ne Assembly - Renew).
2. Remove bolts (x2), inspection cover to lower crankcase, remove cover.
3. Install tool (303-1185) to restrain flywheel, install and tighten bolts (x2).
4. Remove bolts (x6), clutch cover to flywheel.
5. Release clutch cover from dowels (x3), remove clutch cover, collect drive plate.
6. Remove and discard bolts (x8), flywheel to crankshaft flange.
7. Remove bolts (x2), collect tool (303-1185).
8. Release flywheel from dowel, remove flywheel.
9. Position tool (303-1189) to crankshaft flange, screw in
alignment bolts (x2) 1.5 turns (only).
10. Use tool and pierce holes (x3) in oil seal through holes in special tool for self-tapping screws
11. Install and tighten self-tapping screws (x3) into oil seal.
12. Tighten centre bolt of tool (303-1189) and withdraw crankshaft oil seal.
13. Remove oil seal from special tool, discard oil seal.
Installation
1. Clean oil seal aperture in cylinder block.
2. Ensure that oil seal protector is positioned correctly and install oil seal onto crankshaft flange.
3. Install tool (303-1189) to crankshaft, position nuts on
tool against oil seal.
4. Ensure that oil seal and special are parallel to rear of engine.
5. To install oil seal, tighten nuts alternately on tool (303- 1189) until oil seal correctly seated.
6. Remove special tool from crankshaft.
7. Check that the oil seal is located correctly.
8. Clean flywheel and mating face on crankshaft.
9. Install flywheel, align to dowel on crankshaft flange.
10. Install new bolts (x8), install tool (303-1185) to restrain flywheel. Torque tighten bolts (x8) in the correct
sequence.
11. Clean clutch cover and drive plate.
12. Install clutch assembly on flywheel, align to dowels (x3).
13. Install bolts (x6), install clutch alignment tool, evenly torque tighten bolts (x6) in a diagonal sequence.
Remove clutch alignment tool.
14. Remove bolts (x2), collect tool (303-1185).
15. Install inspection cover, install and torque tighten bolts (x2).
16. Install engine assembly (see Workshop Manual procedure 03.00.AA Engine Assembly - Renew).
Repair Operation Time (ROT)
A0311247
Caution
Do not use any lubricant on cr ankshaft oil seals or seal
protectors. Make sure all co mponents are clean and dry
Caution
Alternate nut tightening to correctly seat the crankshaft rear oil seal.

Front Suspension (04.01)
Suspension (04.00)
November 2008 Workshop Manual 4-1-1
Suspension (04.00)
Front Suspension (04.01)
Description
Suspension Arms
The upper suspension arm is attached to the body structure.
The lower suspension arm is attached to the front subframe.
Each upper suspension arm has a press-fit ball-joint, and two
interleaved rubber bushes. Two bolts attach the upper
suspension arm to the body structure.
Each lower suspension arm has a press fit ball-joint and
metal-to-rubber bonded bushes which are attached to the
front subframe by two eccentric cam bolts (Camber and
castor settings).
Anti-roll Bar
The anti-roll bar, is attached to the subframe in two positions
by rubber bushes and clamps. The outer ends of the anti-roll
bar are attached to the lower suspension arms by drop links.
The anti-roll bar provides the required stiffness to control
body roll.
Vertical link
The Vertical link (Knuckle Joint) swivels on the upper and
lower suspension arms via ball-joints, and carries the hub, a
unit 3 wheel bearing (including the ABS encoder ring), the
wheel speed sensor, the brake caliper, and the brake disc
and shield. The position of the Vertical link is determined by
the movement of the steering rack, which is connected to
the Vertical link by the steering track rod.
Specifications
Upper Arm Ball Joint
and Bushes
Ball Joint
and Bushes Verticle
Link
Bolts to Body
Lower Arm
Anti-roll Bar Drop Links
Eccentric
Cam Bolts
04-01-003
Torque Figures
DescriptionNmlb. / ft.
Brake dust shield. 9 7
Bearing Assembly to the Vertical
link. 55 41
Vertical Link to the Lower
Suspension Arm. 90 66.5
Vertical Link to the Upper
Suspension Arm. 90 66.5
Track-rod End Lock Nut. 70 52
Vehicle Ride Height Sensor. M8 M522.5
9 17
7
Anti-roll Bar Link Nuts 110 81.5
Anti-roll Bar Mounting Bolts
Torque bolt 1, then bolt 2, then
bolt 1 again (to allow for rubber
compression) 22.5 17
Torque the following suspensi on fixings with the vehicle
at normal ride height
Lower Suspension Arm front
bush to the Subframe M14 185 137
Lower Suspension Arm rear
bush to the Subframe. M12 115 85
Upper Suspension Arm to the
Front Structure 115 85
Spring and Damper Bolts Top Lower22.5
175 17
129.5
Normal ride height 2 x 37.5kg in front seats (37.5kg in
each seat) plus a full fuel tank.