2010.5 Peugeot 308 SW BL Owner's Manual - RHD (UK. Australia)

1
i
175
PRACTICAL INFORMATION

Fitting a steel or "space-saver"
type spare wheel
If your vehicle is fi tted with al-
loy wheels, it is normal to notice,
when tightening the bolts on fi tting,
that the washers do not come into
contact with the steel or "space-
saver" type spare wheel. The wheel
is secured by the conical contact of
each bolt.


Access to the spare wheel

The spare wheel is supported by a
winch system underneath the rear of
the vehicle.
According to country, the spare wheel
may be steel, alloy or of the "space-
saver" type.
Taking out the wheel


)
Lift up the cover eyelet, pull the cover
upwards, then pivot it to open the
fl ap; these actions release the winch
and give access to its control nut.

)
Unscrew this nut fully, using the
wheelbrace 1
, to unwind the winch
cable.

)
Once the wheel/box is on the
ground, disengage the assembly
from the rear of the vehicle.

)
Detach the hook mechanism to
release the wheel/box assembly, as
shown in the illustration.

)
Take out the black plastic centring
cone.

Access to the set of tools


)
Lift up the wheel to release the set
of tools.

)
To open the storage box, slide the
cover until half open, then pull it off.

1
i
i
176
PRACTICAL INFORMATION

Tyre under-infl ation detection
The spare wheel is not fi tted with
a sensor. The punctured wheel
must be repaired by a PEUGEOT
dealer.
Putting the wheel back in place


)
Store tools 2
and 3
in the box and
close the cover.

)
Position the box on the ground.

)
Place the spare wheel on the box.

)
Fit the black plastic centring cone in
the centre of the wheel (on steel or
"space-saver" type wheels only).

)
Pass the hooking device through
the cone and the wheel to secure it
to the box cover.

)
Raise the wheel/box assembly
underneath the rear of the vehicle
by tightening the winch control nut
using the wheelbrace 1
.

)
Fully tighten the nut.

)
Close the fl ap with the eyelet and
cover to secure the winch.

)
Check that the wheel is located
squarely against the fl oor.
If not, repeat the operation.

If you purchase a wheel of standard
size to replace the "space-saver"
type spare wheel, the spacer, lo-
cated underneath the vehicle, must
be removed. Consult a PEUGEOT
dealer.

1
i
177
PRACTICAL INFORMATION

Parking the vehicle
Immobilise the vehicle where it
does not block traffi c: the ground
must be level, stable and non-slip-
pery ground.
Apply the parking brake, switch off
the ignition and engage fi rst gear *
to lock the wheels.
If necessary, place a chock under
the wheel diagonally opposite the
wheel to be changed.
It is imperative that you ensure that
the occupants get out of the vehicle
and wait where they are safe.
Never go underneath a vehicle
raised using a jack; use an axle
stand.










Removing the wheel

List of operations


)
Fit the security socket 3
on the
wheelbrace 1
to slacken the security
bolt.

)
Slacken the other bolts using the
wheelbrace 1
only.

)
Place the jack 2
in contact with
one of the two front A
or rear B

locations provided on the underbody,
whichever is closest to the wheel to
be changed.

)
Extend the jack 2
until its base plate
is in contact with the ground. Ensure
that the centreline of the jack base
plate is directly below the location A

or B
used.

)
Raise the vehicle until there is
suffi cient space between the wheel
and the ground to admit the spare
(not punctured) wheel easily.

)
Remove the bolts and store them in
a clean place.

)
Remove the wheel.



*
position R
for the electronic gear
control gearbox; P
for the auto-
matic gearbox.

1
i
178
PRACTICAL INFORMATION

After changing a wheel
To store the punctured wheel in the
boot correctly, fi rst remove the cen-
tral cover.
When using the "space-saver" type
spare wheel, do not exceed 50 mph
(80 km/h).
Have the tightening of the bolts and
the pressure of the spare wheel
checked by a PEUGEOT dealer
without delay.
Have the punctured wheel repaired
and replace it on the vehicle as
soon as possible.


Fitting the wheel

List of operations


)
Put the wheel in place on the hub.

)
Screw in the bolts by hand to the
stop.

)
Pre-tighten the security bolt using
the wheelbrace 1
fi tted with the
security socket 3
.

)
Pre-tighten the other bolts using the
wheelbrace 1
only.

)
Lower the vehicle fully.

)
Fold the jack 2
and detach it.

)
Tighten the security bolt using the
wheelbrace 1
fi tted with the security
socket 3
.

)
Tighten the other bolts using the
wheelbrace 1
only.

)
Store the tools in the box.

1
!
!
!
179
PRACTICAL INFORMATION

Risk of electrocution
Xenon bulbs (D1S-35W) must be
replaced by a PEUGEOT dealer.

CHANGING A BULB

Procedure for replacing a faulty bulb with a
new bulb without the use of tools.






Model with halogen headlamps


1.


Direction indicators (PY 21W amber).



2.
Dipped beam headlamps
(H7 - 55W).


3.
Main beam headlamps
(H1 - 55W).


4.
Daytime running lamps/
sidelamps (P 21/5W).


5.
Foglamps (H8 - 35W).





1.
Direction indicators
(PY 21W SV silver).


2.
Directional dipped/main beam
headlamps (D1S-35W).


3.
Additional main beam headlamps
(H1-55W).


4.
Daytime running lamps/
sidelamps (P21/5W).


5.
Foglamps (H8-35W).






























Model with xenon and directional
headlamps
The headlamps are fi tted with poly-
carbonate glass with a protective
coating:


)
do not clean them using a dry
or abrasive cloth, nor with a
detergent or solvent product,


)
use a sponge and soapy water,

)
when using a high pressure
washer on persistent marks,
do not direct at the lamps or
their outlines for too long, so as
not to damage their protective
coating and seals.



)
Do not touch the bulb directly
with your fi ngers, use lint-free
cloths.
Changing a halogen bulb should
only be done after the headlamp has
been switched off for a few minutes
(risk of serious burns).
It is imperative to use only anti-ul-
traviolet (UV) type bulbs in order
not to damage the headlamp.


Front lamps

1
i
!
180
PRACTICAL INFORMATION
















Changing main beam headlamp
bulbs


)
Remove the protective cover by
pulling on the tab.

)
Disconnect the bulb connector.

)
Compress the springs to release the
bulb.

)
Remove the bulb and change it
To r efi t, carry out these operations in
reverse order.

Changing daytime running lamp/
sidelamp bulbs


)
Remove the protective cover by
pulling on the tab.

)
Disconnect the bulb connector.

)
Turn the bulb holder a quarter of a
turn and extract it.

)
Pull the bulb and change it.
To r efi t, carry out these operations in
reverse order.






Changing dipped beam headlamp
bulbs


)
Remove the protective cover by
pulling on the tab.

)
Disconnect the bulb connector.

)
Spread the springs to release the
bulb.

)
Extract the bulb and change it.
To r efi t, carry out these operations in
reverse order.


Changing direction indicator bulbs


)
Turn the bulb holder a quarter of a
turn and extract it.

)
Pull the bulb and change it.
To r efi t, carry out these operations in re-
verse order.
Amber or silver coloured bulbs,
such as the direction indicators,
must be replaced with bulbs of
identical specifi cations and colour.
When refi tting, close the protective
cover carefully to assure the seal-
ing of the headlamp.

1
181
PRACTICAL INFORMATION







Changing foglamp bulbs


)
Insert a screwdriver towards the
centre of the repeater between the
repeater and the base of the mirror.

)
Tilt the screwdriver to extract the
repeater and remove it.

)
Disconnect the repeater connector.
To r efi t, carry out these operations in
reverse order.
Contact a PEUGEOT dealer to obtain
replacement repeaters.

Changing integrated direction
indicator side repeaters
To replace these bulbs consult a
PEUGEOT dealer.

1
i
182
PRACTICAL INFORMATION

































Rear lamps



1.
Brake lamps/sidelamps (P21/5W).


2.
Sidelamps (P21/5W).


3.
Foglamp,

offside

(P21W).


Reversing lamp,

nearside

(P21W).

4.
Direction indicators (P21W).


Changing bulbs
These fi ve bulbs are changed from out-
side the boot:

)
remove the two lamp fi xing nuts,

)
extract the lamp carefully from the
outside,

)
disconnect the lamp connector,

)
press the four tabs and remove the
bulb holder,

)
turn the bulb a quarter of a turn and
change it.
To r efi t, carry out these operations in
reverse order.
If the vehicle is fi tted with the JBL
audio system, on the right-hand
side, fi rst remove the three fi xing
bolts, then move the box.

)
on the right-hand side; remove the
access fl ap,

)
on the left-hand side; turn the fi xing
bolt a quarter of a turn and remove
the storage box cover,

)
unclip the storage box,