2010.5 Peugeot 206 P Dag turn signal
[x] Cancel search: turn signalPage 19 of 119
ii
INSTRUMENTS and CONTROLS
22
COOLANT TEMPERATURE
INDICATOR
System which informs the driver of
the changes in the temperature of the
engine coolant while driving.
With the engine running, when the nee-
dle is:
- in zone A , the temperature is correct,
- in zone B , the temperature is too
high; the max temperature warning
lamp 1 and the central STOP warn-
ing lamp come on, accompanied by
an audible signal and a message in
the multifunction screen.
You MUST stop as soon as it is safe
to do so.
Consult a PEUGEOT dealer. After driving for a few minutes, the tem-
perature and pressure in the cooling
system increase.
To top up the level:
wait for the engine to cool,
unscrew the cap by two turns to
allow the pressure to drop,
when the pressure has dropped,
remove the cap,
top up the level to the "MAX" mark
(circular line).
On petrol engines, the cooling of the
engine is managed electronically
to reduce fuel consumption. Con-
sequently, the coolant temperature
levels are no longer simply linked
with the external ambient condi-
tions and the use of the vehicle.
For example, in town, it is normal for
the coolant temperature to be slight-
ly higher in cold weather than in hot
weather (normal operation may lead
to a temperature of over 100 °).
Page 46 of 119
i
45
Steering lock
Before starting, unlock the steering, if
necessary, by turning the steering wheel
slightly while turning the key.
It is advisable to press the clutch pedal
whle operating the starter to facilitate
the starting of the engine. ELECTRONIC ENGINE
IMMOBILISER
This locks the engine management sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.
If the system does not function cor-
rectly, the central locking button indica-
tor lamp, situated on the centre console,
fl a s h e s r a p i d l y w h e n t h e i g n i t i o n i s
switched on (2nd notch).
In this case your vehicle will not start.
Contact a PEUGEOT dealer as soon as
possible.
Key in ignition
If the key is left in the ignition, this
is indicated by an audible signal
when the driver's door is opened.
Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park:
press button A , the courtesy lamps
come on and the direction indicators
fl a s h f o r a f e w s e c o n d s . Changing the remote control
battery
Battery ref.: CR2016/3 volts.
I f t h e r e m o t e c o n t r o l b a t t e r y i s fl a t , y o u
are warned by a message on display B.
To replace the battery, remove the
screw then unclip the casing using a
coin at the ring.
If the remote control does not work after
the battery has been changed, repro-
gramme the remote control.
Reinitialising the remote control
Switch off the ignition.
Switch the ignition on again.
Press button A immediately for a
few seconds.
Switch off the ignition and remove
the remote control key from the igni-
tion lock. The remote control is now
working again.
Page 48 of 119
i
45
Steering lock
Before starting, unlock the steering, if
necessary, by turning the steering wheel
slightly while turning the key.
It is advisable to press the clutch pedal
whle operating the starter to facilitate
the starting of the engine. ELECTRONIC ENGINE
IMMOBILISER
This locks the engine management sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.
If the system does not function cor-
rectly, the central locking button indica-
tor lamp, situated on the centre console,
fl a s h e s r a p i d l y w h e n t h e i g n i t i o n i s
switched on (2nd notch).
In this case your vehicle will not start.
Contact a PEUGEOT dealer as soon as
possible.
Key in ignition
If the key is left in the ignition, this
is indicated by an audible signal
when the driver's door is opened.
Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park:
press button A , the courtesy lamps
come on and the direction indicators
fl a s h f o r a f e w s e c o n d s . Changing the remote control
battery
Battery ref.: CR2016/3 volts.
I f t h e r e m o t e c o n t r o l b a t t e r y i s fl a t , y o u
are warned by a message on display B.
To replace the battery, remove the
screw then unclip the casing using a
coin at the ring.
If the remote control does not work after
the battery has been changed, repro-
gramme the remote control.
Reinitialising the remote control
Switch off the ignition.
Switch the ignition on again.
Press button A immediately for a
few seconds.
Switch off the ignition and remove
the remote control key from the igni-
tion lock. The remote control is now
working again.
Page 58 of 119
i
56
A u t o m a t i c r a i n s e n s i t i v e w i n d s c r e e n
w i p e r s
In the AUTO position, the windscreen
wipers operate automatically and adapt
their speed to the intensity of the
rainfall .
Operating check
Activation
Activation of the function is accompa-
nied by a message on the multi-function
screen.
In the event of malfunction , the driver
is informed by an audible signal.
In the AUTO position, the windscreen
wiper will operate in intermittent mode.
Contact a PEUGEOT dealer to have the
system checked.
Do not cover the rain sensor located
on the windscreen behind the rear view
mirror.
When using an automatic car wash,
switch off the ignition or check that the
wiper stalk is not in the AUTO position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic rain
sensitive wipers.
W i n d s c r e e n w a s h
Pull the wiper stalk towards you. The
windscreen wash, then the windscreen
w i p e r s , o p e r a t e f o r a s p e c i fi e d t i m e .
R e a r s c r e e n w i p e r
Turn ring A t o t h e fi r s t n o t c h f o r i n t e r m i t -
tent wiping.
I f t h e i g n i t i o n i s s w i t c h e d o f f , i t i s
necessary to reactivate the control
each time . To do this, move the stalk
to any position, then move it back to the
required position.
A u t o m a t i c r e a r s c r e e n w i p e r
When the windscreen wipers control is
activated and you engage reverse gear,
the rear screen wiper operates intermit-
tently.
R e a r s c r e e n w a s h
Turn ring A p a s t t h e fi r s t n o t c h ; t h e
screen wash then the wiper operate for
a fi x e d p e r i o d . If you use a bicycle carrier, con-
sult a PEUGEOT dealer to have
this function deactivated or install
a s p e c i fi c b i c y c l e c a r r i e r a p p r o v e d
by PEUGEOT. COURTESY LAMPS
System for selecting and controlling the
various passenger compartment lamps.
Front courtesy lamp (button A)
- when the vehicle is unlocked,
- when a door is opened,
- when the ignition is switched off.
It switches off when the vehicle is
locked.
I t fl a s h e s w h i l e d r i v i n g i f a d o o r i s n o t
closed correctly.
Permanently off.
Permanently on, when the key
is in the accessories position or
with the ignition on.
In this position, the courtesy
lamp comes on for approxi-
mately 30 seconds:
Page 59 of 119
i
56
A u t o m a t i c r a i n s e n s i t i v e w i n d s c r e e n
w i p e r s
In the AUTO position, the windscreen
wipers operate automatically and adapt
their speed to the intensity of the
rainfall .
Operating check
Activation
Activation of the function is accompa-
nied by a message on the multi-function
screen.
In the event of malfunction , the driver
is informed by an audible signal.
In the AUTO position, the windscreen
wiper will operate in intermittent mode.
Contact a PEUGEOT dealer to have the
system checked.
Do not cover the rain sensor located
on the windscreen behind the rear view
mirror.
When using an automatic car wash,
switch off the ignition or check that the
wiper stalk is not in the AUTO position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic rain
sensitive wipers.
W i n d s c r e e n w a s h
Pull the wiper stalk towards you. The
windscreen wash, then the windscreen
w i p e r s , o p e r a t e f o r a s p e c i fi e d t i m e .
R e a r s c r e e n w i p e r
Turn ring A t o t h e fi r s t n o t c h f o r i n t e r m i t -
tent wiping.
I f t h e i g n i t i o n i s s w i t c h e d o f f , i t i s
necessary to reactivate the control
each time . To do this, move the stalk
to any position, then move it back to the
required position.
A u t o m a t i c r e a r s c r e e n w i p e r
When the windscreen wipers control is
activated and you engage reverse gear,
the rear screen wiper operates intermit-
tently.
R e a r s c r e e n w a s h
Turn ring A p a s t t h e fi r s t n o t c h ; t h e
screen wash then the wiper operate for
a fi x e d p e r i o d . If you use a bicycle carrier, con-
sult a PEUGEOT dealer to have
this function deactivated or install
a s p e c i fi c b i c y c l e c a r r i e r a p p r o v e d
by PEUGEOT. COURTESY LAMPS
System for selecting and controlling the
various passenger compartment lamps.
Front courtesy lamp (button A)
- when the vehicle is unlocked,
- when a door is opened,
- when the ignition is switched off.
It switches off when the vehicle is
locked.
I t fl a s h e s w h i l e d r i v i n g i f a d o o r i s n o t
closed correctly.
Permanently off.
Permanently on, when the key
is in the accessories position or
with the ignition on.
In this position, the courtesy
lamp comes on for approxi-
mately 30 seconds:
Page 66 of 119
63
Operating fault Lateral airbags Deployment
The lateral airbags are deployed uni-
laterally in the event of a serious side
impact applied to all or part of the lat-
eral impact zone
B , perpendicular to
the longitudinal centreline of the vehicle
on a horizontal plane and directed from
the outside towards the inside of the ve-
hicle.
T h e l a t e r a l a i r b a g i n fl a t e s b e t w e e n t h e
occupant of the vehicle and the corre-
sponding door trim panel.
Impact detection zones
A. Front impact zone.
B. Side impact zone.
Deactivating the front
passenger's front airbag
To ensure the safety of your child, it is
essential to deactivate the passenger's
airbag when you install a rear-facing
child seat on the front passenger seat.
Otherwise, the child would risk being
seriously injured or killed if the airbag
w e r e t o i n fl a t e .
With the ignition switched off , insert
the key into the passenger's airbag de-
activation switch, turn it to the "OFF"
position, then remove the key keeping
the switch in the new position. Reactivation
As soon as the child seat is removed,
turn the airbag switch to the
"ON" po-
sition to reactivate the airbag and thus
ensure its safety function.
System which protects the driver in the
event of a serious side impact in order
to limit the risk of injury to the chest.
T h e l a t e r a l a i r b a g i s fi t t e d i n t h e s e a t
back frame, on the door side. When the ignition is on, this
warning lamp remains lit on the
instrument panel if the passen-
ger's airbag is deactivated.
If this warning lamp comes on,
accompanied by an audible
signal and a message in the
multifunction screen, contact a
PEUGEOT dealer to have the airbag
system checked. In the
"OFF" position, the passenger's
airbag will not be triggered in the event
of an impact.
Page 68 of 119
63
Operating fault Lateral airbags Deployment
The lateral airbags are deployed uni-
laterally in the event of a serious side
impact applied to all or part of the lat-
eral impact zone
B , perpendicular to
the longitudinal centreline of the vehicle
on a horizontal plane and directed from
the outside towards the inside of the ve-
hicle.
T h e l a t e r a l a i r b a g i n fl a t e s b e t w e e n t h e
occupant of the vehicle and the corre-
sponding door trim panel.
Impact detection zones
A. Front impact zone.
B. Side impact zone.
Deactivating the front
passenger's front airbag
To ensure the safety of your child, it is
essential to deactivate the passenger's
airbag when you install a rear-facing
child seat on the front passenger seat.
Otherwise, the child would risk being
seriously injured or killed if the airbag
w e r e t o i n fl a t e .
With the ignition switched off , insert
the key into the passenger's airbag de-
activation switch, turn it to the "OFF"
position, then remove the key keeping
the switch in the new position. Reactivation
As soon as the child seat is removed,
turn the airbag switch to the
"ON" po-
sition to reactivate the airbag and thus
ensure its safety function.
System which protects the driver in the
event of a serious side impact in order
to limit the risk of injury to the chest.
T h e l a t e r a l a i r b a g i s fi t t e d i n t h e s e a t
back frame, on the door side. When the ignition is on, this
warning lamp remains lit on the
instrument panel if the passen-
ger's airbag is deactivated.
If this warning lamp comes on,
accompanied by an audible
signal and a message in the
multifunction screen, contact a
PEUGEOT dealer to have the airbag
system checked. In the
"OFF" position, the passenger's
airbag will not be triggered in the event
of an impact.
Page 117 of 119
10
110
Automatic station search
Press button J or L b r i e fl y t o l i s t e n t o
the station immediately above or below.
By continuing to press the button in the
direction selected, you will obtain con-
t i n u o u s s c r o l l i n g o f t h e f r e q u e n c i e s .
T h e s c r o l l i n g s t o p s a t t h e fi r s t s t a t i o n
found when the button is released.
If the TA t r a f fi c i n f o r m a t i o n p r o g r a m m e
is selected, only stations broadcasting
this type of programme are selected.
S e a r c h i n g f o r a s t a t i o n t a k e s p l a c e fi r s t
in "LO" sensitivity (selection of the most
powerful transmitters) during scanning
of the waveband, then in "DX" sensitiv-
i t y ( s e l e c t i o n o f t h e w e a k e s t a n d m o s t
distant transmitters).
To carry out a "DX" sensitivity search
directly, press button J or L twice. Manual station search
Press the
"MAN" button.
Press button J or L b r i e fl y t o i n c r e a s e o r
d e c r e a s e t h e f r e q u e n c y d i s p l a y e d .
By continuing to press the button in the
direction selected, you will obtain con-
t i n u o u s s c r o l l i n g o f t h e f r e q u e n c y .
The scrolling stops as soon as the but-
ton is released.
Pressing the "MAN" button again re-
turns you to the automatic station
search.
Manual storing of stations
S e l e c t t h e s t a t i o n r e q u i r e d .
Press one of the buttons "1" to "6" for
more than two seconds.
The sound stops then becomes audible
a g a i n , c o n fi r m i n g t h a t t h e s t a t i o n h a s
been stored. Automatic storing of FM stations
(autostore)
Press button O for more
than two seconds.
Recalling stored stations
On each waveband, press one of the
buttons "1" to "6" b r i e fl y t o r e c a l l t h e
corresponding stored station.
Your radio automatically stores the
6 stations with the strongest signal on
FM . These stations are stored on the
FMast waveband.
I f i t i s n o t p o s s i b l e t o fi n d s i x s t a t i o n s , t h e
unused memories remain unchanged.