2010.5 Peugeot 206 P Dag seats
[x] Cancel search: seatsPage 4 of 119
FAMILIARISATION
INSTRUMENTS AND CONTROLS
1. Speed limiter/cruise controls.
2. Steering wheel height adjustment
control.
3. Lighting and direction indicator
control stalk.
4. Instrument panel.
Instrument panel lighting dimmer.
5. Driver's airbag.
Horn.
6. Parking brake.
7. Front electric window controls.
8. Central locking control.
9. Bonnet release lever.
10. Fusebox.
11. Headlamp height adjustment.
12. Passenger's airbag deactivation.
13. Heated seats control.
14. ESP/ASR deactivation.
Page 6 of 119
FAMILIARISATION
SITTING COMFORTABLY
FRONT SEAT ADJUSTMENTS
1. Forwards-backwards adjustment.
2. Head restraint height adjustment.
3. Seat back angle adjustment.
37
4. Access to the rear seats (3-door).
5. Height adjustment. STEERING WHEEL ADJUSTMENT
1. Releasing the adjustment mechanism.
2. Adjustment of height.
3. Locking the adjustment mechanism.
42
Page 10 of 119
FAMILIARISATION
MONITORING
1. When the ignition is on, the orange
and red warning lamps come on.
2. When the engine is running, these
warning lamps should go off.
If warning lamps remain on, refer to the
page concerned.
WARNING LAMPS
16
INSTRUMENT PANEL
A. When the ignition is on, the fuel
gauge needle should rise.
B. When the engine is running, the
associated low level warning lamp
should go off.
If the levels are not correct, top up as
required.
15 CONTROLS
A. Passenger's airbag deactivation.
63
B. Heated seats control.
37
C. ESP/ASR deactivation.
59
D. Central locking/unlocking.
48
Page 26 of 119
29
VENTILATION
System which creates and maintains
comfortable conditions in the vehicle's
passenger compartment.
Air paths
The incoming air follows various routes
depending on the controls selected by
the driver:
- direct arrival in the passenger com-partment (air intake),
- passage through a heating circuit (heating),
- passage through a cooling circuit (air conditioning). The temperature control enables you to
obtain the level of comfort required by
mixing the air of the various circuits.
The air distribution control enables you
to diffuse the air in the passenger com-
partment combining several air vents.
T h e a i r fl o w c o n t r o l e n a b l e s y o u t o
increase or reduce the speed of the
ventilation blower.
The air circulating in the passenger
c o m p a r t m e n t i s fi l t e r e d a n d o r i g i n a t e s
either from the outside via the grille lo-
cated on the bonnet or from the inside
in air recirculation mode.
Control panel
The controls of this system are grouped
together on the centre console. De-
pending on the model, the functions
offered are:
- the level of comfort required,
- a i r fl o w ,
- air distribution,
- demisting and defrosting,
- manual or digital air conditioning
controls.
Air diffusion
1. Windscreen demisting/defrosting vents.
2. Front side window demisting/
defrosting vents.
3. Side adjustable air vents.
4. Central adjustable air vents.
5. Air outlets to the front footwells.
6. Lower air outlets (under the front
seats). *
* Only present with digital air conditioning.
Page 27 of 119
i
30
The air conditioning system does
not contain chlorine and does not
present any danger to the ozone
layer.
In order for these systems to be fully effective, follow the operation and
maintenance guidelines below:
If the interior temperature remains very high after the vehicle has been
p a r k e d i n t h e s u n f o r a c o n s i d e r a b l e t i m e , fi r s t v e n t i l a t e t h e p a s s e n g e r
compartment for a few minutes.
P l a c e t h e a i r fl o w c o n t r o l a t a s u f fi c i e n t l e v e l t o p r o v i d e a n a d e q u a t e r e n e w a l
of air in the passenger compartment.
To obtain an even air distribution, take care not to obst ruct the exterior air
intake grille located on the bonnet, the vents and the a ir passages under
the front seats.
Operate the air conditioning system for 5 to 10 minutes, on ce or twice a
month to keep it in good working order.
E n s u r e t h a t t h e p a s s e n g e r c o m p a r t m e n t fi l t e r i s i n g o o d c o n d i t i o n a n d
h a v e t h e fi l t e r e l e m e n t s r e p l a c e d r e g u l a r l y ( r e f e r t o t h e " C h e c k s " s e c t i o n ) .
W e r e c o m m e n d t h e u s e o f a c o m b i n e d p a s s e n g e r c o m p a r t m e n t fi l t e r .
T h a n k s t o i t s s e c o n d s p e c i a l a c t i v e fi l t e r , i t c o n t r i b u t e s t o t h e p u r i fi c a t i o n
of the air breathed by the occupants and the cleanliness of the passenger
compartment (reduction of allergic symptoms, bad odours and greasy
deposits).
To ensure correct operation of the air conditioning system, you are also
advised to have it checked regularly.
If the system does not produce cold air, do not u se it and contact a PEUGEOT
dealer.
When towing the maximum load on a steep gradient in high temperatures,
switching off the air conditioning saves engine power and t herefore improves
towing capacity.
The condensation created by the air conditioning results in a discharge of
water under the vehicle which is perfectly normal.
Page 35 of 119
!i
37
1 - F o r w a r d s - b a c k w a r d s a d j u s t m e n t
Lift the control and slide the seat forwards
or backwards.
2 - Height adjustment
Pull the handle upwards.
Remove your weight from the seat to
raise, or press on the seat to lower.
3 - Access to the rear seats
(3-door), A or B according to model
A. P l a c e y o u r fi n g e r s i n o n e o f t h e t w o
handles and push forwards to fold
down the seat back and move the
seat forwards.
When put back, the seat returns to its initial position.
No person or object must prevent the seat from returning to its initial
position. Returning to this position is
necessary for the seat to lock. 4 - Seat back angle adjustment
Push the handle towards the rear.
5 - Head restraint height adjustment
To raise the head restraint, pull it up-
wards.
T h e a d j u s t m e n t i s c o r r e c t w h e n t h e
upper edge of the head restraint is
l e v e l w i t h t h e t o p o f t h e h e a d .
T h e h e a d r e s t r a i n t i s fi t t e d w i t h a f r a m e
with notches, which prevent the head
restraint dropping down (this is a safety
device in case of impact).
FRONT SEATS
Seat consisting of a seat cushion, seat
back and head restraint which can all
be adjusted to your optimum driving
and comfort position.
Never drive with the head re-
straints removed; they should be
in place and correctly adjusted.
It is impossible to access the rear
seats if the front seat is in a reclin-
ing position.
Heated seats
Press the switch, located on the control
panel next to the steering wheel. The
temperature is regulated automatically.
Press again to switch off.
Rear head restraint
These have a position for use (high)
and a position for storage (low).
To lower the head restraints, press the
lug.
They can also be removed.
To remove the head restraints, pull up-
wards as far as the stop then press the
release control.
To lower the head restraint, push simul-
taneously:
- the button on the left-hand guide
at the base of the head restraint
frame,
- the head restraint downwards.
To remove the head restraint, press the
lug.
B. P l a c e y o u r fi n g e r s i n o n e o f t h e t w o
handles and push forwards to fold
down the seat back. The seat does
not move forwards.
When put back, the seat back re- turns to its initial angle.
Page 36 of 119
!!
38
REAR SEATS
- position the seat belt under the belt holder 2 ,
- pull control 3 to unlock the seat
back 4 ,
- remove or lower the head restraint,
- tilt the seat back 4 . When repositioning:
- return the seat back to the upright
position,
- fold back the seat cushion,
- reposition the seat belt buckles before locking the front of the seat
cushion,
- check that the seats are locked cor- rectly.
Control 3 must be in the low position.
Rear seat or bench seat which can be
folded to adapt the load space in the
boot.
To fold the rear seats:
- lift the front of the seat cushion
1 ,
- tilt the seat cushion 1 against the
front seats,
Take care not to trap the seat
belts.
A l w a y s s t a r t w i t h t h e s e a t
cush-
ion
, never the seat back (risk of
damage).
Page 37 of 119
!!
39
BENCH SEAT
- position the seat belt under the belt holder 2 ,
- pull the controls 3 to unlock the seat
back 4 ,
- remove or lower the head re- straints,
- tilt the seat back 4 . When repositioning:
- return the seat back to the upright
position,
- fold back the seat cushion,
- reposition the seat belt buckles before locking the front of the seat
cushion,
- check that the bench seat is secured fi r m l y .
The controls 3 must be in the low
position.
To fold the bench seat:
- lift the front of the seat cushion
1 ,
- tilt the seat cushion 1 against the
front seats,
Take care not to trap the seat
belts.
A l w a y s s t a r t w i t h t h e s e a t
cush-
ion
, never the seat back (risk of
damage).