2010.5 Citroen DS4 Owner's Manual

This information is displayed for a few seconds when the ignition is switched on, at the same time as the ser vice information.
Engine oil level indicator
The vehicle must be on level ground and the engine must have been off for more than 30 minutes for this level check to be accurate.
Oil level correct
Oil level incorrect
This is indicated by the flashing of "OIL" or the display of a specific message in the instrument
panel, coupled with the ser vice warning lamp and accompanied by an audible signal. If the low oil level is confirmed by a check using
the dipstick, the level must be topped up to avoid damage to the engine.
Oil level indicator fault
This is indicated by the flashing of "OIL - -" or the display of a specific message in the instrument panel. Consult a CITROËN dealer.
There are 2 marks on the dipstick: - A = max; never exceed this level (risk of damage to the engine), - B = min; top up the level via the oil filler cap, using the correct grade of oil for your engine.
Dipstick
Refer to the "Checks" section to locate the dipstick and the oil filler cap on your engine.

51Monitoring
This information is displayed for a few seconds after switching on the ignition. It informs the driver when the next ser vice is due, in accordance with the manufacturer's ser vicing schedule. The point at which the ser vice is due is calculated from the last ser vice indicator zero
reset. It is determined by two parameters: - the distance travelled, - the time elapsed since the last ser vice.
Service indicator
Between 600 miles (1 000 km) and 1 800 miles (3 000 km) remain before the next service is due
For a few seconds after the ignition is switched on, the spanner symbolising the service operations comes on. The distance recorder display line or a specific message in the instrument panel central screen indicates the distance remaining before the next service is due. For example: 1 700 miles (2 800 km) remain before the next ser vice is due. For a few seconds after the ignition is switched on, the screen indicates:
Less than 600 miles (1 000 km) remain before the next service is due
Example: 560 miles (900 km) remain before the next ser vice is due. For a few seconds after the ignition is switched on, the screen indicates:
A few seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on to indicate that a ser vice must be carried out
soon.
A few seconds after the ignition is switched on, the spanner goes off ; the distance recorder s offresumes its normal operation. The screen then indicates the total and trip distances.
More than 1 800 miles (3 000 km) remain before the next service is due
When the ignition is switched on, no service information
appears in the instrument panel central screen.

A few seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on .
The distance remaining may be weighted by the time factor, depending on the type of driving. Therefore, the spanner may also come on if you have exceeded the two year ser vice inter val.
Service indicator zero reset
After each ser vice, the ser vice indicator must be reset to zero. The procedure for resetting to zero is as follows:  switch off the ignition,  press and hold the ".../000" trip distance recorder zero reset button,  switch on the ignition; the distance recorder display begins a countdown,  when the screen indicates "=/0" and the spanner disappears, release the button.
This operation cannot be carried out while a reminder of the ser vicing information is being displayed. Following this operation, if you wish to disconnect the battery, lock the vehicle and wait at least five minutes for the zero reset to be registered.
Recalling the service information
You can recall the ser vice information at any time.  Briefly press the ".../000" trip distance recorder zero reset button. The ser vice information is displayed for a few seconds, in the total distance recorder line or in the instrument panel central colour screen, according to version.
Service overdue
For a few seconds after the ignition is switched on, the spanner flashes to indicate that the service must be carried out as soon as possible. Example: the ser vice is overdue by 180 miles (300 km). For a few seconds after the ignition is switched
on, the screen indicates:

A few seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on .
The distance remaining may be weighted by the time factor, depending on the type of driving. Therefore, the spanner may also come on if you have exceeded the two year ser vice inter val.
Service indicator zero reset
After each ser vice, the ser vice indicator must be reset to zero. The procedure for resetting to zero is as follows:  switch off the ignition,  press and hold the ".../000" trip distance recorder zero reset button,  switch on the ignition; the distance recorder display begins a countdown,  when the screen indicates "=/0" and the spanner disappears, release the button.
This operation cannot be carried out while a reminder of the ser vicing information is being displayed. Following this operation, if you wish to disconnect the battery, lock the vehicle and wait at least five minutes for the zero reset to be registered.
Recalling the service information
You can recall the ser vice information at any time.  Briefly press the ".../000" trip distance recorder zero reset button. The ser vice information is displayed for a few seconds, in the total distance recorder line or in the instrument panel central colour screen, according to version.
Service overdue
For a few seconds after the ignition is switched on, the spanner flashes to indicate that the service must be carried out as soon as possible. Example: the ser vice is overdue by 180 miles (300 km). For a few seconds after the ignition is switched
on, the screen indicates:

Monitoring
Manual test in the central colour screen associated with the satellite navigation system
This function allows you to check the status of the vehicle systems (reminder of the "activated"/"deactivated " status of the configurable functions) and to display the aler ts log.
 With the engine running, to star t a manual test, briefly press the ".../000" button on the instrument panel.
The following information appears successively in the instrument panel central colour screen: - engine oil level indicator (see corresponding section),
- ser vice indicator (see corresponding section), - under-inflation detection (if your vehicle
is fitted with this system; see the "Safety" section), - current warnings and aler t messages, if any (see corresponding section for the warning lamp or system concerned), - status of configurable functions (see
"Multifunction screens").
This information also appears every time the ignition is switched on (automatic test).

The total and trip distances are displayed for thir ty seconds when the ignition is switched off, when the driver's door is opened and when the vehicle is locked or unlocked.
Distance recorders
Total distance recorder Trip distance recorder
Measures a distance travelled since it was reset to zero by the driver.
 With the ignition on, press and hold this button until zeros appear.
Measures the total distance travelled by the vehicle since its first registration.

55Monitoring
Lighting dimmer
Permits manual adjustment of the brightness of the instruments and controls in relation to the exterior brightness. Only operates when the vehicle lighting is on in night mode.
Activation
 Press button A to change the brightness of the instruments and controls.  When the lighting reaches the minimum setting, release the button, then press again to increase it. or  When the lighting reaches the maximum setting, release the button, then press again to reduce it.  When the lighting reaches the level of brightness required, release the button.
This indicator and the lighting
value appear in the middle of the instrument panel during adjustment to show the lighting level compared to the 16 levels available.
You can also modify the level of lighting by turning the thumb wheel B , located on the left of the steering wheel:  upwards; to reduce the level,  downwards; to increase the level.
Deactivation
When the vehicle lighting is off, or in day mode (daytime running lamps on), pressing the button or turning the thumb wheel does not have any effect.

System allowing cer tain screens to be switched
off for night driving. The instrument panel remains on with the analogue vehicle speed, manual or electronic gearbox system gear selected, cruise control or speed limiter information, if in use, and the low fuel aler ts as appropriate. If there is an aler t or a change in a function or to a setting, the black panel mode is interrupted.
Black panel (black screen)
Activation
 With the vehicle lighting on, press this button again to activate the black panel.  Press once more to illuminate on the
various screens again. The dashboard lighting dimmer remains operational when in black panel mode.
In the instrument panel, you can change the colour of its dials (button A ) independently from Athat of the screens (button B ). There are five colour variants, from white to blue.  press the appropriate button as many times as needed to obtain the desired colour.
Customising the instrument
panel colours
In order to retain the digital reading of the speed in km/h, activation of black panel mode is prohibited in countries that use metric units.