2010.5 Citroen C5 DAG battery
[x] Cancel search: batteryPage 36 of 336
I
33
M O N I T O R I N G
Warning lamp is on Cause Action/Observations
Low fuel
level fi x e d . W h e n i t fi r s t c o m e s o n t h e r e
remains
approximately
5 litres of
fuel in the tank. You must refuel as soon as possible to
avoid running out of fuel.
T h i s w a r n i n g l a m p w i l c o m e o n e v e r y t i m e
t h e i g n i t i o n i s s w i t c h e d o n , u n t i l a s u f fi c i e n t
addition of fuel is made.
F u e l t a n k c a p a c i t y : 7 1 l i t r e s .
N e v e r c o n t i n u e t o d r i v e u n t i l y o u r u n o u t
o f f u e l , t h i s c o u l d d a m a g e t h e e m i s s i o n
c o n t r o l a n d i n j e c t i o n s y s t e m s .
Maximum
coolant
temperature fi x e d r e d .
The temperature of the
c o o l i n g s y s t e m i s t o o h i g h . S t o p a s s o o n a s i t i s s a f e t o d o s o .
W a i t u n t i l t h e e n g i n e h a s c o o l e d d o w n
b e f o r e t o p p i n g u p t h e l e v e l , i f n e c e s s a r y .
I f t h e p r o b l e m p e r s i s t s , c o n t a c t a
C I T R O Ë N d e a l e r .
Battery
charge fi x e d . T h e b a t t e r y c h a r g i n g c i r c u i t
h a s a f a u l t ( d i r t y o r l o o s e
t e r m i n a l s , s l a c k o r c u t
a l t e r n a t o r b e l t , . . . ) . The warning lamp should go off when the
engine is started.
I f i t d o e s n o t s w i t c h o f f , c o n t a c t a C I T R O Ë N
dealer.
+
Seat belt not
fastened/
unfastened fi x e d .
T h e d r i v e r a n d / o r t h e f r o n t /
rear passenger has not
fastened or has unfastened
their seat belt. Pull the strap then insert the tongue in the
buckle.
Seat belts
not fastened/ unfastened fi x e d , a s s o c i a t e d
with the seat belt n o t f a s t e n e d /unfastened
warning lampl. The illuminated dots represent the not
f a s t e n e d / u n f a s t e n e d p a s s e n g e r s .
T h e y c o m e o n :
- fi x e d f o r 3 0 a b o u t s e c o n d s o n s t a r t i n g t h e
v e h i c l e ,
- fi x e d f r o m 0 t o 1 2 m p h ( 0 t o 2 0 k m / h ) w h e n d r i v i n g ,
-
fl a s h i n g a b o v e 1 2 m p h ( 2 0 k m / h ) , a c c o m p a n i e d
b y a n a u d i b l e s i g n a l f o r a b o u t 1 2 0 s e c o n d s .
Page 60 of 336
III
!
59
C O M F O R T
Changing the battery
The remote control is supplied by a
6 V-28L battery, which is supplied.
Information on the display indicates
when it is time to replace this battery.
Unclip the casing then replace the
battery.
The remote control must then be re-
initialised, see below. Always switch off the program-
m a b l e h e a t i n g w h i l e fi l l i n g w i t h
f u e l t o a v o i d a n y r i s k o f fi r e o r e x -
plosion.
To avoid any risk of poisoning and
asphyxiation, the programmable
heating must not be used, even
for short periods, in an enclosed
space such as a garage or work-
shop which is not equipped with an
exhaust gas extraction system.
Do not park the vehicle on an
i n fl a m m a b l e s u r f a c e ( d r y g r a s s ,
dead leaves, paper…), there is a
r i s k o f fi r e .
The programmable heating sys-
tem is supplied by the vehicle's fuel
tank. Before use, ensure that the
quantity of fuel remaining is suf-
fi c i e n t . I f t h e f u e l t a n k i s a t t h e r e -
serve, we strongly advise that you
do not programme the heating.
Do not discard the used bat-
teries, take them to an ap-
proved collection point.
Reinitialising the remote control
If the vehicle's battery is disconnect-
ed or the remote control's battery is
replaced, the remote control must
be reinitialised.
After switching on the power, press
button 4 (OFF) for 1 second within
the next 5 seconds. If the operation
has taken place correctly the mes-
sage "OK" is displayed on the re-
mote control screen.
If a problem occurs, the message
"FAIL" appears. Repeat the operation.
In addition, your programmable
heating can be used to pre-heat
your vehicle's passenger com-
partment. The interior volumetric protection
alarm movement sensor may be
d i s t u r b e d b y t h e fl o w o f a i r f r o m
the programmable heating when
it is in operation.
To avoid any unexpected trigger-
ing of the alarm during use of the
programmable heating, it is ad-
visable to deactivate the interior
volumetric protection.
Page 64 of 336
III
63
C O M F O R T
Storing driving positions
System which takes into account the
settings of the driver's seat and air
conditioning. It enables you to store
up to two positions using the buttons
on the side of the driver's seat. Storing a position
Using buttons M/1/2
Switch on the ignition.
Adjust your seat.
Press button M , then press but-
ton 1 or 2 within four seconds.
An audible signal is heard indicating
that the settings have been stored.
Storing a new position cancels the
previous position.
Recalling a stored position
Ignition on or engine running
B r i e fl y p r e s s b u t t o n 1 or 2 to re-
call the corresponding position.
An audible signal is heard indicating
the end of the adjustment.
When the ignition is on, after a few
consecutive position recalls, the
function will be deactivated until the
engine is started, to prevent dis-
charging of the battery. For your safety, avoid storing a
driving position while driving.
REAR HEAD RESTRAINTS
The rear head restraints can be re-
moved and have two positions:
- high, position for use,
- low, storage position.
To raise a head restraint, pull it up-
wards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high posi-
tion, push the lug and pull it upwards.
T o r e fi t i t , e n g a g e t h e h e a d r e s t r a i n t
rods in the holes taking care to re-
main in line with the seat back.
Never drive with the head restraints
removed, they must be in place
and correctly adjusted.
Page 65 of 336
III
63
C O M F O R T
Storing driving positions
System which takes into account the
settings of the driver's seat and air
conditioning. It enables you to store
up to two positions using the buttons
on the side of the driver's seat. Storing a position
Using buttons M/1/2
Switch on the ignition.
Adjust your seat.
Press button M , then press but-
ton 1 or 2 within four seconds.
An audible signal is heard indicating
that the settings have been stored.
Storing a new position cancels the
previous position.
Recalling a stored position
Ignition on or engine running
B r i e fl y p r e s s b u t t o n 1 or 2 to re-
call the corresponding position.
An audible signal is heard indicating
the end of the adjustment.
When the ignition is on, after a few
consecutive position recalls, the
function will be deactivated until the
engine is started, to prevent dis-
charging of the battery. For your safety, avoid storing a
driving position while driving.
REAR HEAD RESTRAINTS
The rear head restraints can be re-
moved and have two positions:
- high, position for use,
- low, storage position.
To raise a head restraint, pull it up-
wards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high posi-
tion, push the lug and pull it upwards.
T o r e fi t i t , e n g a g e t h e h e a d r e s t r a i n t
rods in the holes taking care to re-
main in line with the seat back.
Never drive with the head restraints
removed, they must be in place
and correctly adjusted.
Page 75 of 336
IV
71
A C C E S S
Malfunction
Following disconnection of the ve-
hicle battery, replacement of the re-
mote control battery or in the event
of a remote control malfunction, you
can no longer unlock, lock or locate
your vehicle.
First of all, use the key in the lock
to unlock or lock your vehicle.
Then, reinitialise the remote control.
If the problem persists, contact a
CITROËN dealer as soon as pos-
sible.
Reinitialisation
Switch off the ignition.
Turn the key to position 2 (
Drive
) .
Press the closed padlock imme-
diately for a few seconds, until
the operation requested is trig-
gered.
Switch off the ignition and re-
move the key from the ignition
switch.
The remote control is fully opera-
tional again. Battery ref.: CR0523/3 volts.
This replacement battery is avail-
able from CITROËN dealers.
I f t h e b a t t e r y i s fl a t , y o u
are informed by lighting
of this warning lamp,
an audible signal and a
message on the multifunction screen.
Unclip the casing using a coin at
the notch.
S l i d e t h e fl a t b a t t e r y o u t o f i t s l o -
cation.
Slide the new battery into its loca-
tion observing the original direction.
Clip the casing.
Reinitialise the remote control.
Changing the battery
Page 79 of 336
IV
!
73
A C C E S S
ALARM *
System which protects and provides
a deterrent against theft and break-
ins. It provides the following types of
monitoring.
- Exterior perimeter
The system checks for opening of
the vehicle.
The alarm is triggered if anyone tries
to open a door, the boot, the bonnet...
- Interior volumetric
The system checks for any variation in
the volume in the passenger compart-
ment.
The alarm is triggered if anyone breaks
a window, enters the passenger com-
partment or moves inside the vehicle.
- Tilt
The system checks for any change
in the attitude of the vehicle.
The alarm is triggered if the vehicle
is lifted, moved or knocked. Locking the vehicle with full
alarm system
Activation
Switch off the ignition and get out
of the vehicle.
Press the locking button on the
remote control.
The monitoring system is active: the
i n d i c a t o r l a m p o n t h e b u t t o n fl a s h e s
once per second.
After the locking button on the re-
mote control is pressed, the exterior
perimeter monitoring is activated
after a delay of 5 seconds and the
interior volumetric and anti-tilt moni-
toring after a delay of 45 seconds.
If an opening (door, boot...) is not
closed fully, the vehicle is not locked
but the exterior perimeter monitor-
ing will be activated after a delay of
45 seconds at the same time as the
interior volumetric and anti-tilt moni-
toring. Deactivation
Press the unlocking button on
the remote control.
The alarm system is deactivated: the in-
dicator lamp on the button switches off.
Locking the vehicle with
exterior perimeter monitoring
only
Deactivate the interior volumetric
and anti-tilt monitoring to avoid un-
wanted triggering of the alarm in
certain cases such as:
- leaving a pet in the vehicle,
- leaving a window partially open,
- washing your vehicle,
- changing a wheel,
- having your vehicle towed,
- transport by sea.
Self-protection function
The system checks for the
putting out of service of its
components.
The alarm is triggered if the battery,
the central control or the siren wiring
are put out of service or damaged.
For all work on the alarm system,
contact a CITROËN dealer. Deactivation of the interior
volumetric and anti-tilt
monitoring
Switch off the ignition.
Within ten seconds, press the
button until the indicator lamp is
lit continuously.
Get out of the vehicle.
Press the locking button on the
remote control immediately.
The exterior perimeter monitoring alone
is activated: the indicator lamp on the
b u t t o n fl a s h e s o n c e p e r s e c o n d .
To be effective, this deactivation
must be carried out each time the
ignition is switched off.
Page 84 of 336
IV
78
A C C E S S
Unlocking
Press button A again to unlock
the vehicle.
The red indicator lamp on the button
switches off.
If the vehicle is locked or dead-
locked from the outside, the red in-
d i c a t o r l a m p fl a s h e s a n d b u t t o n A
is inactive.
In this case, use the remote
control or the key to unlock the
vehicle.
Automatic central locking
System which provides full automatic locking or unlocking of the doors and
the boot while driving.
You can activate or deactivate this
function. Locking
When the speed exceeds 6 mph
(10 km/h), the doors and the boot
lock automatically.
If one of the doors is open, the auto-
matic central locking does not take
place.
If the boot is open, the automatic
central locking of the doors is active.
Unlocking
Above 6 mph (10 km/h), press
button A to unlock the doors and
the boot temporarily.
Activation
Press button A for more than
two seconds.
A c o n fi r m a t i o n m e s s a g e a p p e a r s o n
the instrument panel screen, accom-
panied by an audible signal.
Deactivation
Press button A again for more
than two seconds.
A c o n fi r m a t i o n m e s s a g e a p p e a r s o n
the instrument panel screen, accom-
panied by an audible signal.
Emergency control
To lock or unlock the doors manu-
ally in the event of a malfunction of
the central locking system or battery
failure. Locking the driver's door
Insert the key in the lock, then
turn it to the rear.
Unlocking the driver's door
Insert the key in the lock, then
turn it to the front.
Locking the front and rear
passenger doors
On the rear doors, check that the
child lock is not activated.
Remove the black cap, located
on the edge of the door, using
the key.
Insert the key in the socket with-
out forcing it, then without turn-
ing it, move the latch sideways
towards the inside of the door
R e m o v e t h e k e y a n d r e fi t t h e
cap.
Unlocking the front and rear
passenger doors
Pull the interior door opening
control.
Page 85 of 336
IV
79
A C C E S S
BOOT (SALOON)
Press upwards on lever 1 and lift
up the boot lid. With the vehicle stationary, this is
carried out using:
- The remote control.
- The key in a door lock.
- The interior central locking/un-
locking control.
The boot automatically locks when
the vehicle is moving at a speed of
over 6 mph (10 km/h), even if auto-
matic central locking is deactivated.
It is unlocked when a door is opened
or when the central locking button is
pressed (speed lower than 6 mph
(10 km/h)).
Opening
Locking/unlocking Emergency boot release
System for mechanical unlocking of
the boot in the event of a battery or
central locking malfunction.
Unlocking
Fold back the rear seats to gain
access to the lock from inside
the boot.
Insert a small screwdriver into
hole A of the lock to unlock the
tailgate.
Push the white part, located in-
side the lock, to the left to unlock
the boot.