2010.5 Citroen C5 DAG battery
[x] Cancel search: batteryPage 88 of 336
IV
82
A C C E S S
PANORAMIC SUNROOF (SALOON)
Sunroof closed
- Press B t o fi r s t n o t c h : t i l t i n g .
- Press B to second notch: auto-
matic complete tilting.
- Press A t o fi r s t n o t c h : s l i d i n g t o -
wards rear.
- Press A to second notch: auto-
matic total sliding towards rear. Sunroof open
- Press
B t o fi r s t n o t c h : c l o s u r e .
- Press B to second notch: auto-
matic total closure.
Always remove the ignition key
when leaving the vehicle, even if
for a short time .
In the event of anything being
caught by the sunroof closing, you
must reverse the roof movement.
Do this by reversing the position of
the control switch .
When the driver is operating the
sunroof, they must always make
sure that the passengers are not
preventing it from closing properly.
The driver must ensure that pas-
sengers use the sunroof control
correctly.
Pay special attention to where chil-
dren are when operating the sunroof.
T h e fi t t i n g o f a s u n r o o f a s a n a c -
cessory is prohibited
Operation
Tilted sunroof
- Press A t o fi r s t n o t c h : c l o s u r e .
- Press A to second notch: auto-
matic total closure.
Y o u r s u n r o o f i s fi t t e d w i t h a m a n u a l l y -
operated blind.
Anti-pinch
An anti-pinch device stops the sun
roof from closing, whether sliding or
tilting. If it meets an obstacle, it re-
opens. Reinitialisation
After a battery disconnection or if
there has been a malfunction, you
have to re-initialise the anti-pinch
function.
move control B until the roof is in
the complete tilting position,
keep control B pressed down for
a minimum of 1 second.
During these operations, the anti-
pinch function does not operate
.
Page 89 of 336
IV
83
A C C E S S
PANORAMIC SUNROOF (TOURER)
This comprises a tinted glass pan-
oramic area 1 to improve brightness
and vision in the passenger com-
partment.
I t i s fi t t e d w i t h a n e l e c t r i c b l i n d 2 to
help maintain a comfortable temper-
ature and reduce noise. Opening
Press control A .
Pressing to the 1st notch allows you
to open the blind step by step.
Pressing to the 2nd notch allows
you to fully open the blind.
The blind stops in the closest pre-
d e fi n e d p o s i t i o n ( 1 1 p o s i t i o n s ) a s
soon as you release the control.
Closing
Press control B .
Press to the fi r s t n o t c h to close the
blind step by step.
Press to the second notch to close
the blind completely.
The blind stops at the nearest pre-
set position (11 positions) as soon
as you release the control. After a battery disconnection, or if
there has been a malfunction, you
have to re-initialise the anti-pinch
function:
press control B to the 2nd notch
(fully closed),
wait until the blind is fully
closed,
press control B for at least 3 seconds.
If the blind opens randomly during a
closing operation, and straight after
the blind stops:
Press control B until the blind
closes fully.
During these operations, the anti-
pinch function does not operate.
In the event of anything being
caught when the blind is moving,
you must reverse the movement
of the blind. To do so, reverse the
position of the control.
When the driver is operating the
blind, he or she must always make
sure that the passengers are not
preventing it from closing properly.
The driver must ensure that pas-
sengers use the blind correctly.
Pay particular attention to children
when operating the blind .
Anti-pinch
If the blind meets an obstacle whilst
closing, it stops and opens partially
again.
You must re-initialise the anti-pinch
function within 5 seconds of the
blind stopping:
press control B until the blind is
fully closed (closing in steps of a
few centimetres).
SEQUENTIAL ELECTRIC BLIND
Page 93 of 336
V
87
V I S I B I L I T Y
C. Foglamps selection ring.
The foglamps operate with the side-
lamps and the dipped and main
beam headlamps.
-
1 st turn forwards: rear foglamps on.
- 1 st turn rearwards: rear foglamps off.
- 1 st turn forwards: front foglamps on.
- 2 nd turn forwards: rear foglamps on.
- 1 st turn rearwards: rear foglamps off.
- 2 nd turn rearwards: front foglamps off.
Model with rear foglamps
only
Model with front and rear
foglamps In good or rainy weather, both day
and night, the front foglamps and
the rear foglamps are prohibited. In
these situations, the power of their
beams may dazzle other drivers.
They should only be used in fog or
snow.
In these weather conditions, it is
your responsibility to switch on the
foglamps and dipped headlamps
manually as the brightness sensor
m a y d e t e c t s u f fi c i e n t l i g h t .
Do not forget to switch off the front
foglamps and the rear foglamps
when they are no longer necessary.
Lamps on buzzer
The triggering of an audible signal
when a front door is opened warns
the driver that he has forgotten to
switch off his vehicle's lamps, with
the ignition off and in manual lamps
mode.
In this case, switching off the lamps
stops the audible signal.
With the ignition off, if the dipped
headlamps remain on, they will
switch off automatically after thirty
minutes to prevent discharging of
the battery.
Page 119 of 336
VI
1 0 2
F I T T I N G S
BOOT FITTINGS (TOURER)
1. Hook
F o r s h o p p i n g b a g s .
2. Torch
T o r e c h a r g e , r e t u r n i t t o i t s s t o r - a g e p o s i t i o n .
3. Storage net o r Battery com-
partment (for vehicles with
3 litre V6 HDi engine).
T h i s p r o v i d e s a c c e s s t o t h e b a t t e r y .
1. Luggage-cover blind
( s e e d e t a i l s o n f o l l o w i n g p a g e )
2. Luggage securing rings
U s e t h e 4 s t o w i n g r i n g s p r o v i d e d o n t h e b o o t fl o o r t o s e c u r e y o u r
l o a d s .
F o r s a f e t y r e a s o n s i n t h e e v e n t o f s h a r p b r a k i n g , y o u a r e a d -
v i s e d t o p l a c e h e a v y o b j e c t s a s
f a r f o r w a r d s a s p o s s i b l e .
3. Hooks
T h e s e a l l o w a c a r g o n e t t o b e fi t t e d ( s e e d e t a i l s o n f o l l o w i n g
p a g e ) .
1. Boot lamp
2. 12 V accessories socket (100 W
maximum)
C i g a r l i g h t e r t y p e 1 2 v o l t s o c k e t . I t i s l o c a t e d o n t h e r e a r r i g h t -
h a n d t r i m .
3. Loading height control
Y o u c a n c h a n g e t h e h e i g h t o f t h e v e h i c l e t o m a k e l o a d i n g o r u n -
l o a d i n g e a s i e r .
4. Hook
F o r s h o p p i n g b a g s .
5. Storage net o r closed housing
L o c a t i o n f o r t h e 6 C D c h a n g e r .
Page 151 of 336
IX
!
130
D R I V I N G
On sloping ground: immobilise
the vehicle by placing the chocks
(if your vehicle has them) in front
or behind the two front wheels,
against the slope
On level ground: immobilise the vehicle by placing the chocks
(if your vehicle has them) in
front and behind one of the front
wheels.
Open the lower compartment of
the centre armrest by pulling it.
Ensure that the cup holder B is
folded away.
Remove the rubber mat covering
the base of the armrest. This strap does not permit
application of the parking
brake.
To re-engage the electric parking
brake (after rectifying the malfunc-
tion or battery failure), give a long
pull on the control A until the park-
i n g b r a k e w a r n i n g l a m p ( ! ) fl a s h e s
on the instrument panel then give a
second long pull until this warning
l a m p i s o n fi x e d .
The time required for the subse-
quent application may be longer
than during normal operation.
It is essential that the ignition is
not switched on until the parking
b r a k e h a s r e - e n g a g e d ( fl a s h i n g o f
the warning lamp (!) on the instru-
ment panel then the warning lamp
o n fi x e d ) t o a v o i d d a m a g e t o t h e
parking brake.
Take care not to allow moisture or
d u s t i n t h e p r o x i m i t y o f t h e d i a g n o s -
tic socket D which is essential for
the maintenance of your vehicle.
Release the strap from its loca-
tion C .
Pull the strap to release the
b r a k e . A l o u d k n o c k c o n fi r m s t h e
release of the brake.
Take care to put the strap back in
its location C correctly. Otherwise,
it will no longer be possible to ap-
ply the brake. Consult a CITROËN
dealer.
Put the rubber mat back in place
on the base of the armrest.
Page 153 of 336
IX
132
D R I V I N G
SITUATION
CONSEQUENCES
4 Display of messages "
Parking brake faulty "
and " Anti roll-back
fault " and of the following
warning lamps:
and/or fl a s h i n g - The automatic functions are deactivated.
- The hill start assist is not available.
To apply the electric parking brake:
Immobilise the vehicle and switch off the ignition
P u l l t h e c o n t r o l l e v e r f o r a t l e a s t 5 s e c o n d s o r u n t i l m a x i m u m
application.
S w i t c h o n t h e i g n i t i o n a n d c h e c k t h a t t h e e l e c t r i c p a r k i n g b r a k e
warning lamps are on.
- Application may take longer than in normal operation.
- I f w a r n i n g l a m p ( ! ) fl a s h e s o r i f t h e w a r n i n g l a m p s d o n o t c o m e
on when the ignition is switched on, this method does not work.
Have it checked by a CITROËN dealer.
To release the electric parking brake:
S w i t c h o n t h e i g n i t i o n .
P u s h t h e c o n t r o l l e v e r a n d h o l d i t f o r a p p r o x i m a t e l y 3 s e c o n d s .
5 Display of message "
Parking brake control
faulty – automatic mode activated " and the
following warning lamps:
and/or fl a s h i n g - Only the functions for automatic application on switchi
ng off the
engine and automatic release on acceleration are available.
- Manual application/release of the electric parking brake a nd
dynamic emergency braking are unavailable.
6 Display of message "
Parking brake faulty "
and of the following warning lamp:
fl a s h i n g - Application of the parking brake is not guaranteed.
- The parking brake is temporarily unavailable.
It this situation arises:
W a i t a p p r o x i m a t e l y 3 m i n u t e s .
A f t e r 3 m i n u t e s , i f t h e w a r n i n g l a m p i s s t i l l fl a s h i n g , t r y t o r e i n i -
tialise the parking brake, either by pushing and releasing th e
control A while pressing the brake pedal or by means of a long
pull on control A .
7 Battery fault - Lighting of the battery warning lamp ma
kes it essential to stop
t h e v e h i c l e a s s o o n a s t r a f fi c a l l o w s . S t o p a n d i m m o b i l i s e y o u r
vehicle.
- Apply the electric parking brake before switching off the engine.
Page 163 of 336
IX
!
!
142
D R I V I N G
In the event of a malfunction with
the system, the "ECO OFF" switch
w a r n i n g l a m p fl a s h e s t h e n c o m e s
on continuously.
Have it checked by a CITROËN
dealer.
I n t h e e v e n t o f a f a u l t i n S T O P m o d e ,
the vehicle may stall. It is then nec-
essary to switch off the ignition and
start the engine again using the
key.
Operating fault
T h e S t o p & S t a r t s y s t e m
makes use of advanced
t e c h n o l o g y . S p e c i a l i s t k n o w l e d g e
is needed for any work on the sys-
tem, which can only be assured by
CITROËN dealers. Before working under the
b o n n e t , d e a c t i v a t e t h e S t o p &
S t a r t s y s t e m t o a v o i d a n y r i s k
of injury resulting from automatic
o p e r a t i o n o f S T A R T m o d e .
Maintenance
This system requires a battery with
a s p e c i a l s p e c i fi c a t i o n a n d t e c h n o l -
ogy (reference numbers available
from CITROËN dealers).
Fitting a battery not listed by
CITROËN introduces the risk of
malfunction of the system.
Page 185 of 336
X
164
C H E C K S
PETROL ENGINES
The various caps and covers allow
a c c e s s f o r c h e c k i n g fl u i d l e v e l s a n d
for replacing certain components.
1. Screenwash and headlamp wash
reservoir.
2. P o w e r s t e e r i n g fl u i d r e s e r v o i r o r
power steering and suspension
fl u i d r e s e r v o i r .
3. Engine coolant header tank.
4. Engine oil dipstick.
5. E n g i n e o i l fi l l e r c a p .
6. B r a k e fl u i d r e s e r v o i r .
7. Battery.
8. A i r fi l t e r .
1.6i THP
1.8i 16V