2010.5 Citroen C3 PICASSO Owner's Manual

!
122
PRACTICAL INFORMATION
Removing the cartridge

 Stow the black pipe.

 Detach the angled base from the
white pipe.

 Support the compressor vertically.


Unscrew the cartridge from the bottom.
Beware of discharges of fl uid.
The expiry date of the fl uid is indi-
cated on the cartridge.
The sealant cartridge is designed
for single use; even if only partly
used, it must be replaced.
After use, do not discard the car-
tridge into the environment, take
it to an authorised waste disposal
site or a CITROËN dealer.
Do not forget to obtain a new
sealant cartridge, available from
CITROËN dealers. Checking tyre pressures/
inflating accessories
You can also use the compressor, without
injecting any product, to:
- check or adjust the pressure of your
tyres,
- infl ate other accessories.

 Turn the selector A to the
"Air" position.

 Uncoil the black pipe H fully.

 Connect the black pipe to
the valve of the wheel or accessory.
If necessary, fi t one of the adaptors supplied with the kit fi rst.
 Connect the compressor's electri-
cal connector to the vehicle's 12 V
socket.

 Start the vehicle and let the engine
run.

 Adjust the pressure using the com-
pressor (to infl ate: switch B in po-
sition "I" ; to defl ate: switch B in
position "O" and press button C ),
according to the vehicle's tyre pres-
sure label or the accessory's pres-
sure label.

 Remove the kit then stow it.

i
123
PRACTICAL INFORMATION
CHANGING A WHEEL
The tools are installed under the boot
fl oor.
For access to them:

 open the boot,

 remove the boot fl oor,

 lift up the boot carpet,

 remove the box containing the tools,

 remove the polystyrene storage box. All of these tools are specifi c to your
vehicle. Do not use them for other
purposes.
List of tools
Other accessories

6. Removable towing eye.
Refer to the paragraph "Towing the vehicle".
Access to the tools
Wheel with trim

When removing the wheel , fi rst
detach the trim using the wheel-
brace 1 pulling at the valve passage
hole.

When refi tting the wheel , refi t the
trim starting by placing its notch fac-
ing the valve and press around its
edge with the palm of your hand.

1. Wheelbrace.
For removing the wheel trim and removing the wheel fi xing bolts.

2. Jack with integral handle.
For raising the vehicle.

3. "Bolt cover" tool.
For removing the bolt protectors (covers) on alloy wheels.
Procedure for changing a faulty wheel
for the spare wheel using the tools pro-
vided with the vehicle.

4. Centring guide.
For refi tting an alloy wheel to the hub.

5. Socket for the security bolts
(located in the glove box).
For adapting the wheelbrace to the special "security" bolts (if
your vehicle has them).

i
124
PRACTICAL INFORMATION
Fitting the steel or "space-
saver" type spare wheel
If your vehicle is fi tted with alloy
wheels, it is normal to notice, when
tightening the bolts on fi tting, that
the washers do not come into con-
tact with the steel or "space-saver"
type spare wheel. The wheel is
secured by the conical contact of
each bolt.
Access to the spare wheel
The spare wheel is installed in the boot
under the fl oor.
According to country, the spare wheel
may be steel or of the "space-saver"
type.
For access to it, refer to the paragraph
"Access to tools" on the previous page.
Taking out the wheel

 Unscrew the yellow central bolt, and
remove it.

 Raise the spare wheel towards you
from the rear.

 Take the wheel out of the boot.
Putting the wheel back in place

 Put the wheel back in its housing.

 Refi t the yellow central bolt in the
centre of the wheel.

 Tighten fully until the central bolt
clicks to retain the wheel correctly.

 Put the polystyrene storage box
back in place.

 Put the box back in place and clip it.

i
125
PRACTICAL INFORMATION
Parking the vehicle
Immobilise the vehicle where it
does not block traffi c: the ground
must be level, stable and non-
slippery.
Apply the parking brake, switch off
the ignition and engage fi rst gear to
lock the wheels.
If necessary, place a chock under
the wheel diagonally opposite the
wheel to be changed.
You must ensure that the occu-
pants get out of the vehicle and
wait where they are safe.
Never go underneath a vehicle
raised using a jack; use an axle
stand.
Removing the wheel
List of operations

 Remove the chromed bolt cover from
each of the bolts using the tool 3 (with
allow wheels only).

 Fit the security socket 5 on the
wheelbrace 1 to slacken the security
bolt (if your vehicle has them).

 Slacken the other bolts using the
wheelbrace 1 only.

 Place the jack 2 in contact with one
of the two front A or rear B locations
provided on the underbody, which-
ever is closest to the wheel to be
changed.

 Extend the jack 2 until its base plate
is in contact with the ground. Ensure
that the centreline of the jack base
plate is directly below the location A
or B used.

 Raise the vehicle until there is suf-
fi cient space between the wheel and
the ground to admit the spare (not
punctured) wheel easily.

 Remove the bolts and store them in
a clean place.

 Remove the wheel.

i
126
PRACTICAL INFORMATION List of operations

 Put the wheel in place on the hub
using the centring guide 4 .

 Screw in the bolts by hand as far as
possible.

 Pre-tighten the security bolt (if your ve-
hicle has them) using the wheelbrace

1 fi tted with the security socket 5 .

 Pre-tighten the other bolts using the
wheelbrace 1 only.

 Lower the vehicle fully.

 Fold the jack 2 and detach it.
After changing a wheel
To store the punctured wheel in
the boot correctly, fi rst remove the
central cover.
When using the "space-saver"
type spare wheel, do not exceed
50 mph (80 km/h).
Have the tightening of the bolts
and the pressure of the spare
wheel checked by a CITROËN
dealer without delay.
Have the punctured wheel repaired
and replace it on the vehicle as
soon as possible.
Refitting the wheel

 Tighten the security bolt (if your vehicle
has them) using the wheelbrace 1 fi t-
ted with the security socket 5 .

 Tighten the other bolts using the
wheelbrace 1 only.

 Refi t the chromed bolt covers on
each of the bolts (with alloy wheels
only).

 Store the tools in the box.

!
!
127
PRACTICAL INFORMATION
CHANGING A BULB
Procedure for replacing a faulty bulb
with a new bulb.
1. Direction indicators
(H21W amber).

2. Dipped
beam
headlamps
(H7-55W).

3. Main beam headlamps (H1-55W).

4. Sidelamps
(W5W).

5. Foglamps
(PSX24W).
The headlamps are fi tted with poly-
carbonate glass with a protective
coating:

 do not clean them using a dry
or abrasive cloth, nor with a
detergent or solvent product,

 use a sponge and soapy water,

 when using a high pressure
washer on persistent marks, do
not direct at the lamps or their
outlines for too long, so as not
to damage their protective coat-
ing and seals. Front lamps

 Do not touch the bulb directly
with your fi ngers, use lint-free
cloths.
Changing a bulb should only be
done after the headlamp has been
switched off for a few minutes (risk
of serious burns).
It is imperative to use only anti-
ultraviolet (UV) type bulbs in order
not to damage the headlamp.
Always replace a failed bulb with a
new bulb with the same type and
specifi cation.

i
!
i
128
PRACTICAL INFORMATION
Changing direction indicator bulbs
Amber coloured bulbs, such as
the direction indicators, must be
replaced with bulbs of identical
specifi cations and colour.

 Remove the plastic protective cover.

 Pull the bulb-holder and replace the
bulb.
To refi t, carry out these operations in
reverse order.
When refi tting, close the plastic
cover carefully to ensure the sealing
of the headlamp. If either of the direction indicator
warning lamps is fl ashing quickly,
one of the bulbs is faulty.
Changing main beam headlamp
bulbs

 Remove the protective plastic cover
by pulling on the tab.

 Disconnect the bulb connector.

 Move the springs to release the bulb.

 Remove the bulb and change it.
To refi t, carry out these operations in
reverse order.
Changing sidelamp bulbs

 Remove the protective plastic cover
by pulling on the tab.

 Pull the bulb-holder.

 Remove the bulb and replace it.
To refi t, carry out these operations in
reverse order.
Changing dipped headlamp bulbs

 Remove the protective plastic cover
by pulling on the tab.

 Turn the bulb-holder by a quarter
turn.

 Remove the bulb and change it.
To refi t, carry out these operations in
reverse order.

i
i
129
PRACTICAL INFORMATION
Changing integrated direction
indicator side repeaters
Contact a CITROËN dealer to obtain
replacement repeaters.

 Insert a screwdriver on the edge of
the repeater.

 Tilt the screwdriver to extract the
repeater and remove it.

 Disconnect the repeater connector.
When removing:
- be careful not to damage the paintwork of your vehicle with the screwdriver,
- do not allow the wire and the con- nector to slide inside the wing.
To refi t, carry out these operations in re-
verse order.
If you experience any diffi culty
in replacing bulbs, contact your
CITROËN dealer. Changing front foglamp bulbs
To obtain them, contact your CITROËN
dealer.

 Remove the grille located under the
foglamp.

 Disconnect the bulb holder connector,
by pressing on the tab.


Remove the bulb-holber by pressing on
the 2 clips (at the top and the bottom).
To refi t, carry out these operations in
reverse order.
If you experience any diffi culty
in replacing bulbs, contact your
CITROËN dealer.