2009 SKODA YETI lights

Lights and Visibility
68•
You can set the exterior mirrors by hand, if
the power setting function fails at any
time by pressing on the edge of the mirror surface.•
Contact your specialist garage if a fault ex
ists with the power setting of the exterior
mirrors.Automatic dimming exterior mirror*The exterior mirrors are dimmed together with the interior mirror. If the automatic dimming is switched on, the mirror dims
automatically
depending on the light
striking the mirror from the rear. When the interior lights are switched on or the reverse gear is engaged, the mirror always moves back into the
basic position (not dimmed).
Note
•
Automatic mirror dimming operates only properly if the sun screen* for the rear
window is not in use or the light striking the rear of the interior rear-view mirror is not affected by other objects.•
Do not affix any stickers in front of the light sensor, so that you do not impair the
automatic dimming function or put it out of operation.•
If you switch off the automatic dimming interior rear-view mirror, also the exterior
mirror dimming is switched off.sgg.6.book Page 68 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
77
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– The middle seat backrest can be folded
⇒page 74, “Folding rear seats forwards”
forwards and used as armres
t or table with cup holder
⇒page 76, fig. 73
.
– You can place two cups or beverage cans into the recesses.
Note
If the middle rear seat backrest should be
folded forward for lengthy periods, then
make sure that the belt locks are not located below it - this can result in permanent damage to the upholstery.Seat heating of the front seats*You can electrically heat the seat cushions and the seat backrests of the front seats.Front seats– You can switch on and regulate the seat heating of the driver or front passenger
seat by pressing the surface of the regulator at the point at which the symbol is located
 ⇒fig. 74
.
– With one press, you can switch the heating to highest intensity which is indicated
by the lighting up of the three warning lights in the switch.
– With repeated pressing of the switch, the intensity of the heating is down-regulated
up to the switch-off. The intensity of the heating is indicated by the number of illu- minated warning lights in the switch.
WARNING
If, as an occupant, you have a subdued pain and/or temperature sensitivity, e.g. through medication, paralysis or because of chronic illness (e.g. diabetes), we recommend not to use the seat heating.
This can lead to burns on the back, the
posterior and the legs which
are difficult to heal. If the seat heating is used, we
recommend to make regular breaks in your journey when driving long distances, so that in specific cases as
mentioned above the body can recuperate
from the stress of the journey. Please consult your doctor, who can evaluate your specific condition.
Caution
•
You should not kneel on the seats or otherwise apply pressure at specific points in
order to avoid damaging the heating elements of the seat heaters.•
Do not use the seat heating if the seats ar
e not occupied by persons or if objects
are fastened or stored on them, for example a child seat, a bag etc. A fault of the heating elements in the seat heating can occur.•
Do not clean the seats moist
⇒page 197.
Note
•
The seat heating should only be switched on when the engine is running. This has
a significant effect of savi
ng on the battery capacity.
•
If the on-board voltage drops, the seat heating is switched off automatically, in
order to provide sufficient electrical energy for the engine control.PedalsConcerning a secure depressing of the peda
l, you should use only footmats from the
Škoda genuine accessories. Operation of the pedals must not be hindered!
WARNING
•
Greater pedal distances may be needed when there is a fault in the brake
system.
Fig. 74 Dash panel: Regulator for front seat heating
sgg.6.book Page 77 Thursday, September 24, 2009 2:32 PM

Heating and air conditioning system
98Recirculated air mode In recirculated air mode air is sucked
out of the interior of the vehicle
and then fed back into the interior.Recirculated air mode prevents polluted air
outside the vehicle from getting into the
vehicle, for example when driving through a
tunnel or when standi
ng in a traffic jam.
Switching recirculated air mode on– Press the button - the warning light lights up in the button
⇒page 96, fig. 108
.
Switching recirculated air mode off– Press again the button - the warning light in the button goes out. The recirculated air mode is switched off automatically if the air distribution control is in position
 ⇒page 96, fig. 108
. You can also switch recirculated air mode on
again from this setting by re
peatedly pressing button .
WARNING
You should not leave recirculated air mode on over a longer period of time, as “stale” air may result in fatigue in the driver and occupants, divert your atten-tion and also cause the windows to mist up. The risk of having an accident increases. Switch recirculated air mode off as soon as the windows begin misting up.Climatic* (semi-automatic air conditioning system)Description The Climatic is a combined cooling and heating system. It makes it possible to optimally control the air
temperature at any season of the
year.Description of the Climatic It is important for your safety and for your
driving comfort that the Climatic is operating
properly.
The cooling only operates if button
⇒page 99, fig. 109
is pressed, and the
following conditions are met:•
engine running,
•
outside temperature above approx. +2°C and
•
blower switch switched
on (positions 1 to 4).
If the cooling system is switched on, th
e temperature and air humidity drops in the
vehicle. The wellbeing of the occupants of the car is enhanced as a result of this partic- ularly at high outside temperatures and a high air humidity. The system prevents the windows misting up during the cold season of the year. The heating effect is dependent upon the coolant temperature, thus full heat output only occurs when the engine has reached its operating temperature. It is possible to briefly activate recirculat
ed air mode in order to enhance the cooling
effect
⇒
.
Air at a temperature of about 5°C may flow
out of the vents under certain circum-
stances when the cooling system is operatin
g. Lengthy and uneven distribution of the
air flow out of the vents and large differences in temperature, for example when getting out of the vehicle, can result in chills in sensitive persons. The air inlet in front of the windscreen must be free of ice, snow or leaves in order to ensure that the heating and cooling systems operate properly. After switching on the cooling
Condensation
from the evaporator of the air condi-
tioning may drip down and form a puddle be
low the vehicle. This is quite normal and
not an indication of a leak!
WARNING
•
For your own safety and that of other road users, ensure that all the
windows are free of ice, snow and misting. Please familiarize yourself about how to correctly operate
the heating and ventilation systems, how to demist
and defrost the windows, as well as with the cooling mode.•
You should not leave recirculated air mode on over a longer period of time,
as “stale” air may result in fatigue in the driver and occupants, divert your attention and also cause the windows to mist up. The risk of having an accident increases. Switch recirculated air mo
de off as soon as the windows begin
misting up.


AC

AC
A1
sgg.6.book Page 98 Thursday, September 24, 2009 2:32 PM

Heating and air conditioning system
99
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Note
•
We recommend that you do not smoke in the vehicle when the recirculating air
mode is operating since the smoke which is drawn at the evaporator from the interior of the vehicle forms deposits in the evapor
ator of the air conditioning system. This
produces a permanent odour when the air co
nditioning system is operating which can
only be eliminated through considerable
effort and expense (replacement of
compressor).Using the systemFig. 109 Climatic: Control elementsSetting temperature– Turn the control dial
⇒fig. 109
to the right in order to increase the temperature.
– Turn the control dial to the left in order to increase the temperature.Controlling blower– Turn the blower switch into one of the po
sitions, 1 to 4, in order to switch the
blower on.
– Turn the blower switch into position 0 in order to switch the blower off. – If you wish to shut off the fresh air supp
ly, use the button - recirculated air
mode
⇒page 101.
Control for air distribution– You can adjust the direction of the air
flow using the air distribution control
⇒ page 95.
Switching cooling on and off– Press the button
⇒fig. 109
. The warning light lights up in the button.
– When you again press the switch , the cooling system is switched off. The
warning light in the button goes out.
Rear window heater– Press button . Further information
⇒page 62, “Rear window heater”.
Auxiliary heating (auxiliary heating)– Press the button in order to direct
ly switch on/off the auxiliary heating
(auxiliary heating and ventilation). Further information
⇒page 105, “Auxiliary
heating (auxiliary heating and ventilation)*”.
The set temperature will be automatica
lly maintained other than when the
control dial is on the extreme
right or extreme left position:
•
Extreme right position - full heating;
•
Extreme left position - full cooling;
•
The blower should aways be on to
prevent the windows from misting up.
Note
•
T h e w h o l e h e a t o u t p u t w i l l b e n e e d e d t o u n f ro s t t h e w i n d s c re e n a n d s i d e w i n d o w s .
No warm air will be fed to the footwell. Th
is can lead to restriction of the heating
comfort.•
The used air streams out through the air
removal openings in the luggage compart-
ment.•
If the cooling system has not been switched on for a lengthy period, odours may
be produced at the evaporator because of
deposits. Switch the cooling system on at
least once a month for approximately 5 minu
tes at the highest blower stage - also
during the cold season of the year - in order to remove such odours. Also open a window for a short time.
AAAAABAB

A4
AC
AC
A1
AC

A2A3
sgg.6.book Page 99 Thursday, September 24, 2009 2:32 PM

Heating and air conditioning system
101
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Recirculated air mode In recirculated air mode air is sucked out of the interior of the vehicle and then fed back into the interior.Recirculated air mode prevents polluted air
outside the vehicle from getting into the
vehicle, for example when driving through a
tunnel or when standi
ng in a traffic jam.
Switching recirculated air mode on– Press the button
⇒page 99, fig. 109
the warning light lights up in the
button.
Switching recirculated air mode off– Press again the button - the warning light in the button goes out. The recirculated air mode is switched off automatically if the air distribution control is in position
 ⇒page 99, fig. 109
. You can also switch recirculated air mode on
again from this setting by re
peatedly pressing button .
WARNING
You should not leave recirculated air mode on over a longer period of time, as “stale” air may result in fatigue in the driver and occupants, divert your atten- tion and also cause the windows to mist up. The risk of having an accident increases. Switch recirculated air mode off as soon as the windows begin misting up.Using the air conditioning system economicallyThe compressor on the air conditioning syst
em uses power from the engine when in
cooling mode which will effect the fuel consumption. It recommended to open the windows or the
doors of a vehicle for which the interior
has been strongly heated through the effect
of direct sunlight in order to allow the
heated air to escape. The cooling system should not be switched
on while travelling when the window is
open.
The desired interior temperature can also be achieved without switching in the cooling system just by switching to fresh air mode.
For the sake of the environment
When you economize on fuel, you
also reduce pollutant emissions.
Operational problemsIf the cooling system does not operate at outside temperatures higher than +5 °C, there is a problem in the system. The reasons for this may be:•
The fuse on the air conditioning system has blown. Check the fuse, replace it if
necessary
⇒page 233.
•
The cooling system has switched off auto
matically for a short time because the
coolant temperature of the engine is too hot
⇒page 17.
If you are not able to rectify the operational
problem yourself, or if the cooling capacity
decreases, switch the cooling system off. Contact a specialist garage.Climatronic* (automatic air conditioning)Description The Climatronic system is a combination of an automatic heating, fresh air and cooling system which provides optimal comfort for the occu-pants of the car.The Climatronic maintains fully automatically a convenience temperature. This is achieved by automatically varying the temperature of the outflowing air, the blower stages and the air distribution. The system also takes into account sunlight which elim- inates the need to alter the settings manually. The
automatic mode
⇒page 103
ensures maximum wellbeing of the occupants at all times of the year. Description of Climatronic system The cooling operates only if the following conditions are met:•
engine running,

A4
AC

sgg.6.book Page 101 Thursday, September 24, 2009 2:32 PM

Heating and air conditioning system
103
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Overview of the control elements The controls enable a separate setting of the temperature for the left and right side.Fig. 110 Climatronic: Control elementsThe buttons
Defrost windscreen intensively Air flow to the windows Air flow to head Air flow in the footwell Recirculated air mode
with air quality sensor
Rear window heater
Buttons / control dial
Setting of the temperature for the left side, operation of the seat heating of the left front seat* Automatic mode Switching off Climatronic Setting the blower speed Button for direct switching on/off of auxiliary heating (auxiliary heating)* ⇒ page 105 Switching on/off of the temperature setting in dual mode
Switching cooling on and off Setting of the temperature for the right side, operation of the seat heating of the right front seat*Note
Below the top row of buttons is located the interior temperature sensor. Do not glue or cover over the sensor, otherwise it co
uld have an unfavourable effect on the
Climatronic.Automatic mode The automatic mode is used in orde
r to maintain a constant tempera-
ture and to demist the windows in the interior of the car.Switching automatic mode on– Set a temperature between +18 °C and +26 °C. – Move the air outlet vents
3 and
4 ⇒page 95, fig. 106
, so that the air flow is directed
slightly upwards.
– Press the button . In the right or left top corner a warning light lights up,
depending on which unit was last selected.
If the warning light in the top right corner of the button lights up, the Climatronic operates in “HIGH” mode. The “HIGH” mode is the standard setting of the Climatronic. When pressing again the button , the Cl
imatronic changes into the “LOW” mode
and the warning light in the top left corner lights up. The Climatronic uses only in this mode the lower blower speed. However taking
into account the no
ise level, this is
more comfortable, yet be aware that the effectiveness of the air conditioning system is reduced particularly if th
e vehicle is fully occupied.
By pressing again the button , yo
u change into the “HIGH” mode.
The automatic mode is switched off by pres
sing the button for the air distribution or
increasing or decreasing the blower speed. The temperature is nevertheless regulated.
A1

A2

A3

A4

A5

A6

A7A8
AUTO
A9
OFF
A10

A11

A12
DUAL
A13
AC
A14
AUTO
AUTO
AUTOAUTO
sgg.6.book Page 103 Thursday, September 24, 2009 2:32 PM

Heating and air conditioning system
104
Switching cooling on and offSwitching cooling on and off–Press the button
⇒page 103, fig. 110
. The warning light lights up in the button.
– When you again press the switch , the cooling system is switched off. The
warning light in the button goes out. Only
the function of the ventilation remains
active when no lower temperature than the outside temperature can be reached.
Setting temperatureYou can separate the interior temperature for the left and right side separately. – You can set the temperature for both sides
after switching on the ignition with the
control dial .
– If you wish to set the temperature for the right side, turn the control dial . The
warning light in the button lights up,
this indicates that differing tempera-
tures for the left and right side can be set.
If the warning light in the button lights up, the temperature for both sides cannot be set with the control dial . You can
reinitiate this functi
on by pressing the
button . The warning light in the button which indicates the possibility to set differing temperatures for the left and right side, goes out. You can set the interior temperature between +18°C and +26°C. The interior temper- ature is regulated automatically within this
range. If you chose a temperature lower
than +18°C, a blue symbol lights up at the
start of the numerical
scale. If you chose a
temperature higher than +26°C, a red symbol lights up at the end of the numerical scale. In both limit positions the Climatroni
c operates at maximum cooling or heating
capacity, respectively. The temperatur
e is not controlled in this case.
Lengthy and uneven distri
bution of the air flow out of the vents (in particular at the leg
area) and large differences in temperature, for example when getting out of the vehicle, can result in chills in sensitive persons.
Recirculated air mode In recirculated air mode air is sucked out of the interior of the vehicle and then fed back into the interior. When the automatic air distribution control is switched on, an air quality sensor measures the concentration of pollutants in the drawn-in air.Recirculated air mode prevents polluted air outside the vehicle from getting into the vehicle, for example when driving through a tunn
el or when standing in a traffic jam. If
a considerable increase in concentration of
pollutants is recognized by the air quality
sensor, when the automatic air distribution co
ntrol is switched on, the air distribution
control will temporarily be switched off. If
the concentration of po
llutants decreases to
the normal level, the air distribution control
is automatically switched off so that fresh
air can be guided into
the vehicle interior.
Switching recirculated air mode on– Press the button repeatedly
until the warning light on the left side of the
button lights up.
Switch on automatic air distribution control– Press the button repeatedly
until the warning light on the right side of the
button lights up.
Switch off automatic air distribution control temporarily– If the air quality sensor does not switch on
the air distribution control automatically
when there is a nauseating smell, you can
switch it on yourself by pressing the
button *. The warning light lights up
in the button on the left side.
Switching recirculated air mode off– Press the button or press the button repetitively, until the warning
lights in the button go out.
WARNING
You should not leave recirculated air mode on over a longer period of time, as “stale” air may result in fatigue in the driver and occupants, divert your atten-
AC
AC
A7
A14
DUALDUALA7
DUAL


AUTO

sgg.6.book Page 104 Thursday, September 24, 2009 2:32 PM

Heating and air conditioning system
105
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
tion and also cause the windows to mist up. The risk of having an accident increases. Switch recirculated air mode off as soon as the windows begin misting up.
Note
If the windscreen mists up, press the button
⇒page 103, fig. 110
. After the
windscreen has been demisted, press the button .•
The automatic air distribution control operates only if the outside temperature is
higher than approx. 2°C.Controlling blower There are a total of seven blower stages available.The Climatronic system controls the blower st
ages automatically in line with the inte-
rior temperature. You can also
, howev er, a dapt the bl ower stage s ma nua lly to sui t y our
particular needs. – Press again the button on the left side (reduce blower speed) or on the right
side (increase blower speed).
If you switch off the blower, the Climatronic is switched off. The set blower speed is displayed above the button when the respective number of warning lights come on.
WARNING
•
“Stale air” may result in fatigue in the driver and occupants, reduce atten-
tion levels and also cause the windows to mist up. The risk of having an accident increases.•
Do not switch the Climatronic system off for longer than necessary.
•
Switch the Climatronic system on as soon as the windows mist up.
Defrosting windscreenDefrosting windscreen - switching on– Press the button
⇒page 103, fig. 110
.
Defrosting windscreen - switching off– Once again press the button or the button . The temperature control is controlled automatically. More air flows out of the air outlet vents
1 and
2.
Auxiliary heating (auxiliary heating and ventilation)*Description and important information The auxiliary heating (auxiliary he
ating and ventilation) heats or
supplies the interior of the vehicl
e with fresh air independent of the
engine.Auxiliary heating (auxiliary heating) The auxiliary heating (auxiliary heating) functions in connection with the Climatic or Climatronic. It can be used when stationary, when engi
ne is switched off for preheating of the
vehicle as well as while driving (only during the heating phase of the engine). The auxiliary heating (auxiliary heating) wa
rms up the coolant during the combustion
of fuel from the vehicle tank. The coolant warms up the air, which (if the blower speed is not set to zero) flows into the occupant compartment. Auxiliary ventilation The auxiliary ventilation enables fresh air to flow into the vehicle interior by switching off the engine, whereby the interior temperature is effectively decreased (e.g. with the vehicle parked in the sun).
WARNING (continued)

A1AUTO




AUTO
sgg.6.book Page 105 Thursday, September 24, 2009 2:32 PM