2009 SKODA YETI buttons

Unlocking and locking
48 Closing a window– A window is closed through pulling lightly on the respective button in the door. The
closing process stops when
one releases the button.
– Additionally you can close the window auto
matically (fully clos
ed) by pulling the
button up to the stop. Renewed pulling of the button causes the window to stop immediately.
The buttons for the individual windows are located in the armrest of the driver's door ⇒ page 47, fig. 40
, front passenger door and in the rear doors*
⇒page 48.
Buttons for the power windows in the armrest for the driver Button for the power window in the driver's door Button for the power window in the front passenger's door Button for the power window in the rear door on the right* Button for the power window in the rear door on the left* Safety pushbutton* Safety pushbutton* You can deactivate the buttons for power wind
ows at rear doors by pressing the safety
pushbutton
⇒page 47, fig. 40
. The buttons for power windows at rear doors are
activated again by pressing
the safety pushbutton again.
If the buttons for the rear doors are deactivated, the indicator light
 in the safety
switch lights up.
WARNING
•
If you lock the vehicle from the outside, do not leave any person in the
vehicle since it is no longer possible to
open the windows from the inside in an
emergency.•
The system is fitted with a force limiter
⇒page 49. If there is an obstacle, the
closing process is stopped and the window
goes down by several centimeters.
You should then take particular care when closing the windows! You may otherwise suffer severe injuries as a re
sult of getting an arm, for example,
jammed in the window!
•
It is recommended to deactivate the el
ectrically operated
power windows in
the rear doors (safety pushbutton)
⇒page 47, fig. 40
when children are
being transported on the rear seats.
Note
•
After switching the ignition off, it is still
possible to open or close the windows for a
further 10 minutes. The automatic closing and opening functions will not operate during this time. The power windows are sw
itched off completely once you open the
driver or front passenger door.•
When driving always use the existing he
ating, air conditioning and ventilation
system for ventilating the interior of the vehicle. If the windows are opened, dust as well as other dirt can get into the vehicle an
d in addition the wind noise is more at
certain speeds.Button in front passenger door and in rear doorsA button for the relevant window is provided in these doors.Opening a window– Lightly press the appropriate button
down
and hold it until the window has moved
into the desired position.
AAABACADAS
AS
AS
AS
WARNING (continued)
AS
Fig. 41 Position of button in front passenger door
sgg.6.book Page 48 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
71
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
•
The seat backrests must not be angled too far back when driving otherwise
this will affect proper operation of the se
at belts and of the airbag system - risk
of injury!
Note
If the movement of the seat is inadverten
tly interrupted during an adjustment, once
again press the switch in the appropriate di
rection and continue with the adjustment
of the seat to the end.Storing settingStoring seat and exterior mirror settings for driving forward– Switch on the ignition. – Adjust the seat
⇒page 70.
– Adjust both exterior mirrors
⇒page 67.
– Press button
SET

⇒fig. 64
.
– Press one of the memory buttons with
in 10 seconds after pressing the button
SET
- an acknowledgement signal confirms that the seat setting is stored.
Storing exterior mirror setting for reversing*– Switch on the ignition.
– Turn the exterior mirror control to position
 ⇒page 67.
– Engage the reverse gear. – Move the right exterior mirror
into the desired position
⇒page 67.
– Take the vehicle out of gear. The set posi
tion of the exterior mirror is stored.
Memory buttons Memory for the seat offers the possibility to store the individual driver seat and external mirror position. An individual posi
tion can be allocated to each of the three
memory buttons
⇒fig. 64
, that is three in total. Af
ter pressing the corresponding
memory button , the seat and the exterior
mirror are automatically moved into the
positions which have been allocated to this button
⇒page 71.
Emergency Off You can interrupt the setting operation at any time, if you operate any button of the driver seat.
Note
•
For safety reasons, it is not possible to store this position if the inclination angle of
the seat backrest is more than 102
° in relation to the seat cushion.
•
When storing settings with the memory
buttons, we recommend that you begin
with the front button and assign a memory button to each additional driver.•
Each new setting stored with the same button erases the previous setting.
•
Each time you store the seat and exterior mirror settings for driving forward you
also have to re-store the individual setting
of the exterior mirror on the passenger side
for reversing.Assigning remote control to the memory buttonsAfter storing the settings of the seat and exterior mirrors, you have 10 seconds in order to assign the radio remote control to the appropriate memory button. – Withdraw the ignition key.
WARNING (continued)
Fig. 64 Driver seat: Memory buttons and SET button
AA
AB
ABAB
sgg.6.book Page 71 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
72– Press the unlock button
⇒page 45, after the successful assignment an audible
signal will sound. The setting is stored with the memory button which you have selected.
If you wish to be able to retrieve the settings which are stored in the memory by also using the radio remote control, you have
to assign the radio remote control to a
memory button in each case. If you wish, you can obtain an
additional remote control key from a specialist garage
and then assign the remote control key to another memory button.
Note
•
If the radio remote control had previous
ly been assigned to another memory
button, this setting is then
erased by the new assignment.
•
If you assign the radio remote control to
a memory button which has already been
assigned to a radio remote control, the ol
d assignment is also replaced by a new
assignment in this case.•
The assignment of the radio remote co
ntrol to a memory button is retained,
however, after reassigning the seats and exterior mirrors.Retrieving settings of the seat and mirrors You can retrieve the stored settings either with the memory buttons or with the remote control*.Retrieving settings with memory buttons– In order to retrieve the stored setting, you have two possibilities: –
By pressing briefly:
briefly press the desired memory button
⇒page 71,
fig. 64
. The seat and exterior mirror are move
d automatically into the stored posi-
tions (this applies only if the ignition is switched on and the speed is less than 5 km/h).
–
By pressing for a long period of time:
press and hold the desired memory button
pressed long enough until the seat and the exterior mirrors are moved into the stored positions.
Retrieving settings with remote control– If the driver door is closed and the ignition is switched off, briefly press the unlock
button of the radio remote control
⇒page 45 and then open the driver door.
– The seat and exterior mirrors now move automatically into the stored positions.Retrieving setting of exterior mirror for reversing*– Turn the rotary knob for the exterior mirror setting into the position
 ⇒page 67
before engaging the reverse gear.
The mirror returns into its initial position
, after the rotary knob is moved out of the
position
 and put into another position or if the speed is more than 15 km/h.
Emergency Off You can interrupt the setting operation at any time, if you operate any button of the driver seat.Head restraintsFig. 65 Adjusting head restraint / pulling outBest protection is achieved if the top edge of the head restraint is at the same level as the upper part of your head.Adjusting the height of a head restraint– Grasp the side of the head restraint with both hands and push the head restraint up
or down in direction of arrow
⇒fig. 65
.
AB
AB
A1
sgg.6.book Page 72 Thursday, September 24, 2009 2:32 PM

Heating and air conditioning system
103
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Overview of the control elements The controls enable a separate setting of the temperature for the left and right side.Fig. 110 Climatronic: Control elementsThe buttons
Defrost windscreen intensively Air flow to the windows Air flow to head Air flow in the footwell Recirculated air mode
with air quality sensor
Rear window heater
Buttons / control dial
Setting of the temperature for the left side, operation of the seat heating of the left front seat* Automatic mode Switching off Climatronic Setting the blower speed Button for direct switching on/off of auxiliary heating (auxiliary heating)* ⇒ page 105 Switching on/off of the temperature setting in dual mode
Switching cooling on and off Setting of the temperature for the right side, operation of the seat heating of the right front seat*Note
Below the top row of buttons is located the interior temperature sensor. Do not glue or cover over the sensor, otherwise it co
uld have an unfavourable effect on the
Climatronic.Automatic mode The automatic mode is used in orde
r to maintain a constant tempera-
ture and to demist the windows in the interior of the car.Switching automatic mode on– Set a temperature between +18 °C and +26 °C. – Move the air outlet vents
3 and
4 ⇒page 95, fig. 106
, so that the air flow is directed
slightly upwards.
– Press the button . In the right or left top corner a warning light lights up,
depending on which unit was last selected.
If the warning light in the top right corner of the button lights up, the Climatronic operates in “HIGH” mode. The “HIGH” mode is the standard setting of the Climatronic. When pressing again the button , the Cl
imatronic changes into the “LOW” mode
and the warning light in the top left corner lights up. The Climatronic uses only in this mode the lower blower speed. However taking
into account the no
ise level, this is
more comfortable, yet be aware that the effectiveness of the air conditioning system is reduced particularly if th
e vehicle is fully occupied.
By pressing again the button , yo
u change into the “HIGH” mode.
The automatic mode is switched off by pres
sing the button for the air distribution or
increasing or decreasing the blower speed. The temperature is nevertheless regulated.
A1

A2

A3

A4

A5

A6

A7A8
AUTO
A9
OFF
A10

A11

A12
DUAL
A13
AC
A14
AUTO
AUTO
AUTOAUTO
sgg.6.book Page 103 Thursday, September 24, 2009 2:32 PM

Communication
126
CommunicationMultifunction steering wheel*Operate radio und navigation on the multifunction steering wheelThe driver can set the basic functions of th
e radio and navigation by simply operating
the buttons located on the steering wheel so
that he can concentrate on the traffic situ-
ation without being distracted as little as
possible by operating the radio and naviga-
tion
⇒fig. 126
.
This applies only if your vehicl
e has been installed with radio
11) or navigation system
at the factory. You can of course operate th
e radio and navigation at the appliance. You
will find a description in the operating instructions of your radio. When the headlights are switched on, the steering wheel pushbuttons are then also illuminated. The buttons apply for the respective operating mode of the current radio or navigation system. By pressing the buttons, you can carry out the following functions:11)Does not apply for Radio Blues.
Fig. 126 Multifunction steering wheel: control buttons
sgg.6.book Page 126 Thursday, September 24, 2009 2:32 PM

Communication
131
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
in a jacket pocket, this can lead to diff
iculties when establishing the Bluetooth
®
connection with the handsfree-
system or the data transfer.
Inserting the mobile phone with the adapter* Inserting the mobile phone into the adapter ensures an optimal sending and receiving power and offers at the same time the advan- tage of the battery charging.Only one telephone mount* is factory-fitted. An adapter for the telephone can be purchased from the range of the Škoda original accessories.Inserting the mobile phone with the adapter– First of all push the adapter in the direction of arrow
⇒fig. 127
up to the stop
into the mount. Press the adapter slightly downwards, until it locks securely into position.
– Insert the mobile phone into the adapter (as specified in manufacturer's
instructions).
Removing the mobile phone with the adapter– Press simultaneouly the side locks of the mount and remove the mobile phone and
adapter
⇒fig. 127
.
Note
Please operate your mobile phone exclusively with a suitable adapter in order to keep a low radiation in the vehicle.Operation of the telephone on the multifunction steering wheel*The driver can set the basic functions of th
e telephone by simply operating the buttons
located on the steering wheel so that he can concentrate on the traffic situation without being distracted as little as
possible by operating the telephone
⇒fig. 128
.
This applies only if your vehicle has been equipped with the telephone preinstallation at the factory. If the side lights are switched on, the buttons on the multifunction steering wheel are illuminated. Overview of the different functions in contrast to the multifunction steering wheel without mobile phone operation
⇒page 126.
Fig. 127 Universal preparation for the phone
AA
AA
Button
Action
Operation
press briefly
Activation/deactivation button for voice control
(button PTT)

 turn upwards
Increase volume

 turn down- wards
Decrease volumeFig. 128 Multifunction steering wheel: Control buttons for the telephone
A1A1A1
sgg.6.book Page 131 Thursday, September 24, 2009 2:32 PM

Communication
132
The buttons operate the functions for the
operating mode of the current telephone.
Operate the telephone via the information display*The display of texts in the menu
Phone
is possible in the following languages:
Czech, English, German, French,
Italian, Spanish and Russian.
If you select the menu point
Phone
on the information display with the aid of the
handwheel , you can change to the following menus:„
Phone book
„
Last calls
„
Received calls
„
Missed calls
Phone book In the menu point
Phone book
is the list of the loaded
contacts from the telephone
memory and the SIM card of the mobile phone. In the phone phonebook there are 1 500 free memory locations available.Voice control of the telephoneIntroductionFig. 129 Illustration image: Single
-button adapter / two-button adapter
On vehicles which are factory-fitted with a na
vigation system with voice control*, it is
only possible to operate the voice control via the navigation system*. The description on how to operate the voice control can be fo
und in the operating instructions of your
navigation system*. The voice control of the telephone is
activated by pressing the button
 (button push
to talk) on the adapter*
⇒fig. 129
or by briefly pressing the button on the multi-
function steering wheel*
⇒page 131, fig. 128
.
Aside from the PTT button, the SOS butt
on can be found on certain adapters*
⇒ fig. 129
. This button is without function.
Note
The adapters illustrated
are only prime examples.

 press briefly
Accept call, terminate call,
entry in the main menu of the telephone

 press button for a long time
Reject call,
entry in the main menu of the telephone

 press briefly
Reach one level higher in the menu

 press button for a long time
Return in the main menu

press briefly
Confirm menu selection

press button for a long period of
time
Confirm menu selection,
the following initial letters in the telephone book

 turn upwards
Previous menu point

 turn down- wards
Next menu point
Button
Action
Operation
A2A2A3A3A4A4A4A4
A4
A1
sgg.6.book Page 132 Thursday, September 24, 2009 2:32 PM

Communication
136
Load CDs– Hold the button pressed and guide the CDs one after the other (maximum
6 CDs) into the CD case . The LEDs in
the buttons are no longer flashing.
Loading a CD to one definite position– Press on the button . The LEDs in the
buttons light up at the memory spaces,
which are already assigned and flash in the case of free memory spaces.
– Touch the desired button and
guide the CD into the CD-case .
Ejecting a CD– Briefly press on the button , in order to eject a CD. For assigned memory spaces,
now the LEDs light up in the buttons .
– Touch the corresponding bu
tton . The CD is ejected.
Ejecting all CDs– Hold the button pressed for more than 2
seconds, in order to eject the CDs. All
CDs in the CD-changer are ejected consecutively.Note
•
Always guide the CD into the CD-case
with the printed side pointing upwards.
•
Never push the CD with force into the CD-case as the insertion is performed auto-
matically.•
After loading a CD into the CD-changer, yo
u must wait until the LED of the corre-
sponding button lights up. Then the CD
-case is free to load the next CD.
•
If you have selected a position, on which
a CD is already located, this CD will be
ejected. Take out the ejected CD and load the desired CD.
AA
AB
AD
AA
AD
AD
AB
AC
AD
AD
AC
AB
AD
AB
sgg.6.book Page 136 Thursday, September 24, 2009 2:32 PM