2009 SKODA OCTAVIA TOUR weight

Transporting children safely
126
This applies particularly to children if they are not transported in accordance with legal requirements. The child is protected when seated in a child safety seat matching its age. Adequate room is available between th
e child and the deployment area of the side airbag and
head airbag. The airbag offers optimal protection.
WARNING
•
It is essential to always switch off the front passenger airbag and possibly
the side airbag* when attaching a child safety seat on the front passenger seat where the child is seated with its back facing in direction of travel (in some countries also when the child is facing the direction of travel) ⇒ page 120. If this is not done, there is a risk of the child suffering severe or even fatal injuries if the front passen
ger airbag is deploy
ed. In certain coun-
tries national legal provisions also re
quire that the side
airbags be deacti-
vated. When transporting a child on the front passenger seat, please comply with the appropriate national regulations regarding the use of child safety seats.•
When transporting a child on the fr
ont passenger seat, please comply
with the appropriate national regulations regarding the use of child safety seats.•
Children must never be seated with their head in the deployment area of
the side airbag - risk of injury!•
Do not place any objects within the deployment area of the side airbag -
risk of injury!Child seatClassification of child seats into groups Only child safety seats which have an official approval and are suit- able for the child, may be used.ECE-R 44 standard applies to child safety seats. ECE-R means: Standard Economic Commission of Europe - Regulation.
Child safety seats which have been tested for conformity to ECE-R 44 standard have a non-detachable test seal (a large E within a circle and below this the test number) attached to the seat. Child safety seats are classified in 5 groups: Children of more than 150 cm in height may use the seat belts fitted to the vehicle without a seat bolster.Use of child safety seatsAn overview of the usefulness of child se
ats on each of the seats according to the
EG guidelines 77/541 and ECE 44 standard:
Universal category - seat is suitable for all approved types of child safety seats. The seat can be fitted with
fixing eyes for the “
ISOFIX
*”system.
Group
Weight
0
0 - 10 kg
⇒page 127
0+
up to 13 kg
⇒page 127
1
9 - 18 kg
⇒page 127
2
15 - 25 kg
⇒page 128
3
22 - 36 kg
⇒page 128
Child seat of the group
Front passenger
seat
Rear seat outside
Rear seat middle
0


0+


1


2 and 3
AUA+
AUA+
AU
AUA+
AUA+
AU
AUA+
AUA+
AU
AU
AU
AU
AUA+
s2g8.b.book Page 126 Tuesday, April 7, 2009 8:53 AM

Transporting children safely
127
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Child seats of group 0/0+The optimal solution for babies of up to
about 9 months old weighing up to 10 kg
or babies up to about 18 mont
hs old weighing up to 13
kg is a child safety seat
which can be adjusted into the reclining position
⇒fig. 133
.
In view of the fact that such child seats are installed that the child is seated with its back facing the direction of travel, they
must not be used on the front passenger
seat
⇒page 124, “Use of child safety seats on the front passenger seat”.WARNING
•
It is essential to always switch off the front passenger airbag (airbags)
when attaching in exceptional circumstances a child safety seat on the front passenger seat where the child is seated
with its back facing in direction of
travel (in some countries also when the child is facing the direction of travel).
− in a specialist garage − or by using the switch for the front passenger airbag*
⇒page 121.
•
In certain countries national legal provisions require that besides the
front passenger airbag also the front passenger side airbag is deactivated. Please comply with any differing national legal regulations regarding the use of child safety seats.
•
If this is not done, a child seated on
the front passenger seat may suffer
severe or even fatal injuries if the
front passenger airbag or airbags are
deployed.•
You should have the front passenger ai
rbag (or airbags) reactivated just
as soon as you no longer use a child sa
fety seat on the front passenger seat.
Child safety seats in Group 1Child seats in Group 1 are for babies and sm
all children up to 4 years of age with a
weight of between 9 and 18 kilograms. It is
best for children in the lower range of
this group, to use a child seat which allows
the child to sit with its back to the direc-
tion of travel. It is best for children in the upper range of the Group 0+, to use a child seat which allows the child to sit
⇒fig. 134
in the direction of travel.
Child safety seats in which the child is seat
ed with its back facing the direction of
travel, must not be used on the front passenger seat
⇒page 124, “Use of child
safety seats on the front passenger seat”.
WARNING
•
It is essential to always switch of
f the front passenger airbag (airbags)
when attaching in exceptional circumstances a child safety seat on the front
Fig. 133 Child seats of group 0/0+
WARNING (continued)
Fig. 134 Child seat with padded table in Group 1 installed on rear seat bench facing the direction of travel
s2g8.b.book Page 127 Tuesday, April 7, 2009 8:53 AM

Driving and the Environment
141
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Avoid driving short distances Short distances result in an above-average high fuel consumption.– Avoid driving a distance of no more than 4 km if the engine is cold.The engine and catalytic converter mu
st first have reached their optimal
operating
temperature
in order to effectively reduce fu
el consumption and pollutant emis-
sions. The cold engine vehicle consumes approx. 15 - 20 litres/100 km of fuel immediately after starting. Fuel co
nsumption drops to 10 litres/100 km after just 1 kilometre. The
engine reaches its operating temperat
ure (outside temperature and engine
dependent) only after about
4 to 10
kilometres and the fuel consumption then
stabilizes. You should therefore avoid driving short distances whenever possible. An important factor in this connection is also the
ambient temperature
. The
⇒ fig. 143
shows the different fuel consumptions for the same distance, on the one
hand at +20°C and on the other hand at
-10°C. Your vehicle has a higher fuel
consumption in winter than in summer.Checking tyre inflation pressures Tyres which are correctly inflated save fuel.Always ensure that your tyres are inflated
to the correct pressure at all times. The
rolling resistance will be increased if the tyre filling pressure is too low. This will not
only increase fuel consumption but also
tyre wear and the driving behaviour will
worsen. Always check the inflation pressure of the tyres when
cold
.
Do not drive with
winter tyres
all year round for this costs about 10 % more fuel.
Winter tyres are also louder.No unnecessary ballast Transporting ballast costs fuel.The fact that every kilogram of extra
weight
increases your fuel consumption
means that it is worth taking a look in the luggage compartment to avoid trans- porting any unnecessary ballast. It is particularly in town traffic, when one
is accelerating quite often, that the vehicle
weight will have a significant effect upon
the fuel consumption. A rule of thumb
here is that an increase in weight of 100
kilograms will cause an increase in fuel
consumption of about 1
litre/100 kilometres.
You may frequently also leave a
roof rack fitted
on just out of convenience,
although you no longer need it. The incr
eased aerodynamic drag of your vehicle
causes it to use about 10% more fuel th
an normal at a speed of 100 - 120 km/h,
even when you are not carr
ying a load on the roof.
Saving electricity Generating electricity costs fuel.– Switch off electrical components as
soon as you no longer need them.
When the engine is running, the alternator
generates and supplies
electrical power.
The greater the load on the alternator as a result of having a large number of elec-trical components switched on, the more
fuel will be consumed for operating the
alternator.
Fig. 143 Fuel consumption in litres/100 km at different temperatures
s2g8.b.book Page 141 Tuesday, April 7, 2009 8:53 AM

Towing a trailer
144
Towing a trailerTo w i n g a t r a i l e rTechnical requirements The towing device must satisfy
certain technical requirements.
Your vehicle is designed primarily for tr
ansporting persons and luggage. It can,
however, also be used for towing a traile
r - provided certain te
chnical equipment is
fitted. If your vehicle has already been supplied with a
factory-fitted
towing device then
everything that is necessary
for towing a trailer in technical terms, and in terms of
the law, has already been taken into account. Your vehicle is fitted with a 13-pin po
wer socket for the electrical connection
between the vehicle and trailer. If th
e trailer which you wish to tow has a
7-pin
connector
, you can use a suitable adapter
5) from Škoda original accessories.
This work must be carried out in accordan
ce with the manufacturer's specifications
if a towing device is retrofitted. Specialist garages are familiar with details
relating to retrofitting a towing device
and for any necessary modifications to the cooling system.
WARNING
We recommend that you have the towing device from Škoda original acces-sories installed by a specialist garage.
He is familiar with all the relevant
details relating to retrofitting such equi
pment. There is a risk of an accident
if the towing device is not properly fitted!
General Maintenance There are a number of points to
pay attention to when towing a
trailer.Trailer load The permissible trailer load must
on no account be exceeded.
You can negotiate appropriatel
y steeper inclines and desc
ents if you do not make
full use of the perm
issible trailer load.
The trailer loads specified only apply for
altitudes
up to 1 000 metres above mean
sea level. The fact that the engine power ou
tput drops with increasing height due to
a lowering of air pressure and thus the abil
ity to climb, means that the towed weight
must be reduced by 10% for every further increase of 1 000 metres in height above sea level. The towed weight is the weight of the (laden) vehicle and the (laden) trailer together. One should take this into account before driving up to higher alti- tudes. The trailer and drawbar load information on the type plate of the towing device are merely test data for the tow
ing device The data relating to your
vehicle, which is often less than this test data, can be found in your vehicle registration documents. Distribution of the load Distribute the load in the trailer in such a way that any heavy items are located as close as possible to the axle. Secure
the items to prevent them slipping.
Tyre inflation pressure Select the tyre inflation pressure on your vehicle for that of “fully laden”, ⇒ page 173. The inflation pressure of the tyres fitted to the trailer adjust in accord- ance with the manufacturer's recommendation. Exterior mirrors You have to have additional
exterior mirrors fitted if you are not able to see the
traffic behind the trailer with the standard rear-view mirrors. Both exterior mirrors
5)In some countries the adapter is
supplied with the towing device.
s2g8.b.book Page 144 Tuesday, April 7, 2009 8:53 AM

Towing a trailer
145
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
should be attached to folding arms. Adjust
the mirrors so that they provide you with
an adequate field of view to the rear. Headlights Before starting off with a hitched trailer, also check the setting of the headlights. Alter the setting as necessary with th
e aid of the headlight beam adjuster
⇒ page 51. Detachable ball head The ball rod is detachable on vehicles which feature a factory-fitted towing device. It is stowed together with separate fitting instructions in the spare wheel well in the luggage compartment of the vehicle. Further information on the towing device
⇒page 146.
Note
•
We recommend that you also have yo
ur vehicle inspected between service
intervals if you tow a trailer frequently.•
The handbrake on the towing vehicle
must be put on when coupling and
decoupling the trailer.Driving Tips Particular caution is required when towing a trailer.– Do not, as far as possible, drive
with your vehicle unladen and the
trailer laden.
– Do not make full use of the legal maximum speeds. This applies in
particular to downhill sections.
– Apply the brakes in good time.– Keep a check on the coolant temper
ature gauge if the outside temper-
ature is high.
Distribution of weight The distribution of the weight is very poor
if your vehicle is
unladen and the trailer
is laden. Maintain a particularly low speed if you cannot avoid driving with this combination. Driving speed Do not drive faster than 80 km/hour for safety reasons. This also applies for coun- tries in which higher speeds are allowed. The fact that the driving stability of the vehicle + trailer combination reduces with increasing speed means that the legally allowed speed should not be used when there are unfavourable road, weather or wind
conditions, particul
arly near accident
black spots. You must always reduce your speed immedi
ately as soon as you detect even just
the
slightest swaying
of the trailer. On no account attempt to stop the trailer from
“swaying” by
accelerating.
Apply the brakes in good time! If the trailer is fitted with a
trailer brake
, apply the
brakes gently at first and then brake firmly
. This will avoid brake jolts resulting from
the trailer wheels locking. Shift down gears
in good time before negotiating a down-
hill section to allow the engine to also act as a brake. Engine overheating Please keep a check on the coolant temperature gauge if you have to negotiate a lengthy slope in a low gear at a high engine speed when the outside temperature is very high
⇒page 16.
If the needle of the coolant temperature gauge moves into the right-hand area or even the red area of the scale, reduce yo
ur speed immediately. Stop and switch off
the engine if the warning light
 in the instrument cluste
r begins flashing. Wait a
few minutes and check the level of coolant in the coolant expansion bottle ⇒ page 165, “Inspecting the coolant level”. Please refer to the following guidelines
⇒page 30, “Coolant temperature/ Coolant
quantity
”.
The coolant temperature can be reduced by switching on the heating.Any increase in the cooling effect of the coolant fan through shifting down a gear and increasing the engine speed is not possible since the fan speed is independent
s2g8.b.book Page 145 Tuesday, April 7, 2009 8:53 AM

Technical Data
201
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Technical DataTechnical DataGeneral informationThe details given in the official vehicle
registration document
s always take prece-
dence over the details in th
e Owner's Manual. Please refe
r to the official vehicle
registration documents or consult a specia
list garage concerning the engine with
which your vehicle is equipped.Used abbreviationsPerformancesThe listed performance values were determined without performance-reducing equipment, e.g. air
conditioning system.
WeightThe loading capacity is reduced in line with the range of the special equipment. The unloaden weight contains a fu
el tank topped up to 90%. A driver with a weight of
75 kg is also included in the value.Identification detailsVehicle data sticker The vehicle data sticker
⇒fig. 188
is located on the floor of the luggage compart-
ment and is also stated in the Service schedule. The vehicle data sticker co
ntains the following data:
Vehicle identificati
on number (VIN)
Vehicle type
Abbreviation
Importance
kW
Kilowatt, measuring unit for the engine output
rpm
Engine revolutions per minute
Nm
Newton meter, measuring unit for the engine torque
CO2 in g/km
discharged quantity of carbon dioxide in grams per driven kilom- eter
RON
Research octane number, measur
ing unit for the knocking resist-
ance of petrol
M5
5-speed manual gearbox
PD
Unit injector engine
Fig. 188 Vehicle data sticker
A1A2
s2g8.b.book Page 201 Tuesday, April 7, 2009 8:53 AM

Technical Data
205
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Capacities (in liter) Weight (in kg)Fuel tank capacity/of which spare
55/7
Reservoir for windscreen washer system/ with headlight cleaning system
3/5,5
Engine oil
a)
a)Oil capacity with oil filter change. Inspect oil
level according to filling - see Owner's Manual.
3,2
Cooling system of the vehicle
5,5
OCTAVIA - M5
COMBI - M5
Permissible gross weight
1750
1770
Unloaden weight ready for work
1230
1245
Loading capacity
520
525
Loading capacity when using the TLC
470
475
Permissible front axle load
1000
1000
Permissible rear axle load
990
1000
Permissible trailer loads, trailer braked
850
a)/850
b)
a)For uphills up to 12%.b)Only country specific up to 8% uphill.
850
a)/850
b)
Permissible trailer loads, trailer unbraked
500
500
s2g8.b.book Page 205 Tuesday, April 7, 2009 8:53 AM

Technical Data
207
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Capacities (in liter) Weight (in kg)Fuel tank capacity/of which spare
55/7
Reservoir for windscreen washer system/ with headlight cleaning system
3/5,5
Engine oil
a)
a)Oil capacity with oil filter change. Inspect oil
level according to filling - see Owner's Manual.
4,5
Cooling system of the vehicle
7,0
OCTAVIA - M5
CO M B I - M 5
Permissible gross weight
1790
1805
Unloaden weight ready for work
1260
1275
Loading capacity
530
530
Loading capacity when using the TLC
470
470
Permissible front axle load
1000
1000
Permissible rear axle load
990
1000
Permissible trailer loads, trailer braked
1200
a)/1400
b)
a)For uphills up to 12%.b)Only country specific up to 8% uphill.
1200
a)/1400
b)
Permissible trailer loads, trailer unbraked
500
500
s2g8.b.book Page 207 Tuesday, April 7, 2009 8:53 AM