2009 SKODA OCTAVIA lock

Fuel
222
RefuellingThe filler flap is automatically unlocked or locked* with the central locking. Opening the fuel filler cap – Press onto the left side of the fuel filler flap
⇒
fig. 205
.
– The fuel filler cap on the fuel fille
r tube must be unlocked to the left
using the vehicle key (only valid for
vehicles which do not have auto-
matic unlocking of the fuel filler flap).
– Unscrew the fuel filler cap anti-clo
ckwise and place the fuel filler cap
from above on the fuel filler flap
⇒
fig. 206
.
Closing fuel filler cap – Screw on the fuel filler cap by turning it to the right until it is heard to
click.
– The fuel filler cap on the fuel filler tube must be locked to the right
using the vehicle key (only valid for
vehicles which do not have auto-
matic locking of the fuel filler flap).
– Close the fuel filler flap until it locks.The correct grade of fuel for your vehicle as
well as the tyre size and inflation pres-
sures are stated on a sticker affixed to the inside of the fuel filler flap. Further infor- mation on fuel
⇒page 219.
The fuel tank has a capacity of
about 55°litres or 60 litres
19).
WARNING
Pay attention to any legal requirements if
you do carry a spare canister in the
vehicle. We do not recommend carrying any fuel canisters in your vehicle for safety reasons. The canister can be da
maged in the event of an accident and
fuel may leak out.
Caution
•
Before refuelling it is necessary to switch off the auxiliary heating system (auxil-
iary heating and ventilation) *.•
Remove any fuel which has spilled onto
the paintwork of your vehicle immedi-
ately - risk of paint damage!•
On vehicles fitted with
a catalytic converter, never let the fuel tank run
completely empty. An irregular supply of fu
el to the engine can result in misfiring
Fig. 205 Right rear side of the vehicle: Open fuel filler flapFig. 206 Fuel filler flap with cap unscrewed
19)Valid for Octavia Combi 4x4 and Octavia Scout.
se0.1.book Page 222 Frida
y, April 10, 2009 3:19 PM

Inspecting and replenishing
224
Inspecting and replenishingEngine compartmentBonnet remote releaseBonnet remote release – Pull the unlocking lever below the
dash panel on the driver's side
⇒
fig. 207
.
The bonnet jumps out of its lock as a result of the spring force. A locking lever appears at the same time in the radiator grille.
Opening and closing the bonnet.Opening the bonnet – Unlock the bonnet
⇒
fig. 207
.
– Ensure that the arms of the windsc
reen wipers are correctly in place
against the windscreen
before opening
the bonnet otherwise
damage could occur to the paintwork.
Fig. 207 Bonnet release lever
Fig. 208 Radiator grille: Lever of the locking buttonFig. 209 Securing the bonnet with the bonnet support
se0.1.book Page 224 Frida
y, April 10, 2009 3:19 PM

Inspecting and replenishing
225
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– Pulling on the locking lever
⇒
page 224, fig. 208
will unlock the
bonnet fully.
– Grip with the hand under
the radiator grille and lift up the bonnet.
– Take the bonnet support out of its holder and set it in the opening
designed for it
⇒
page 224, fig. 209
.
Closing the bonnet – Lift the bonnet slightly and unhook the bonnet support. Press the
bonnet support into the hold
er designed to hold it.
– Allow the bonnet to drop from a height of about 20 cm into the lock -
bonnet
do not press down on it
!
WARNING
•
Never open the bonnet if you see that steam or coolant is flowing out of
the engine compartment - risk of scaldi
ng! Wait long enough until the steam
or coolant has stopped escaping.•
For safety reasons, the bonnet must always be properly closed when
driving. One should therefore check that
the lock has in fact engaged prop-
erly after closing the bonnet.•
Stop your vehicle immediately while driv
ing if you notice that the lock is
not properly engaged and close the bonne
t properly - risk of an accident!
Caution
Never open the bonnet using the locking lever - danger of causing damage.Working in the engine compartment Particular care is required when carrying out any work in the engine compartment!There is a risk of injuries, scalding,
accidents and fire when working in the
engine compartment, e.g. inspecting and replenishing oil and other fluids. For
this reason, it is essential to comply with the warning instructions stated below and with the general applicable
rules of safety. The engine compart-
ment of your car is a hazardous area
⇒
.
WARNING
•
Never open the bonnet if you see that steam or coolant is flowing out of
the engine compartment - risk of scaldi
ng! Wait long enough until the steam
or coolant has stopped escaping.•
Switch off the engine and pull out the ignition key.
•
Apply the handbrake firmly.
•
If your vehicle is fitted with a ma
nual gearbox, move the gearshift lever
into Neutral, or if it is fitted with
automatic gearbox, move the selector lever
into position P.•
Allow the engine to cool down.
•
Keep children clear of the engine compartment.
•
Never spill oil and other fluids over the hot engine. Such fluids (e.g. the
antifreeze contained in the coolant) may ignite!•
Avoid short circuits in the electrical system - particularly on the battery.
•
Never place your hand into the radiator fan as long as the engine is still
warm. The fan might suddenly start running!•
Never open the cap of the coolant expa
nsion bottle as long
as the engine
is still warm. The cooling system is pressurized!•
Cover over the cap of the coolant expansion reservoir with a large cloth
when opening it as protection for your
face, hands and arms from hot steam
or hot coolant.•
Do not let objects, such as e.g cleani
ng cloth or tools lie in the engine
compartment.•
If you wish to work under the vehicle, you must secure the vehicle from
rolling away and support it with suitab
le supporting blocks
; the lifting jack*
is not sufficient for this - risk of injury!•
In cases where it be necessary to carry out inspection work when the
engine is running there is an additional risk from rotating parts (e.g. the V-
se0.1.book Page 225 Frida
y, April 10, 2009 3:19 PM

Inspecting and replenishing
230
Losses can only occur through the pressure
relief in the cap of the coolant expan-
sion bottle which is completely free of leak
s if the coolant boils as a result of over-
heating and is forced out of the cooling system.
WARNING
Read and observe the warning notes
⇒page 225, “Working in the engine
compartment” before working in the engine compartment.
Caution
One should contact a specialist garage as soon as possible if the source of over-heating itself cannot be
determined and removed, since there may be grave
damage to the engine.Replenishing the coolant– Switch the engine off. – Allow the engine to cool down. – Place a cloth over the cap of the coolant expansion reservoir
⇒
page 229, fig. 212
and unscrew the cap
carefully
by turning it to the
left
⇒
.
– Top up the coolant. – Screw the cap tight until it is heard to lock.The coolant which you use for replenishing the system, must comply with one specific specification
⇒page 228. Do not use an alternative additive if the coolant
additive G12 PLUS is not available in exceptional cases. Just top up the system with water and as soon as possible arrange ad
justment to correct the mixing ratio of
water and coolant additive again by a specialist garage. Only use fresh coolant for topping up the system.
Do not fill up over the “MAX” marking! Excess coolant which is heated up is forced out of the cooling system through the pressure relief valve in the cap of the coolant compensation bottle. Wait until the engine has cooled down for a system which has suffered a major loss of coolant before pouring in coolant. This is necessary to avoid engine damage.
WARNING
•
The cooling system is pressurized! Do not open the cap of the coolant
expansion bottle if the engine is
still hot - risk of scalding!
•
The coolant additive and thus all of the coolant is harmful to your health.
Avoid contact with the coolant. Coolant vapours are also harmful to the health. It is important, therefore, to always safely store any coolant additive in its original container out of the reach of children - risk of poisoning!•
If any splashes of coolant get into yo
ur eyes, rinse out
your eyes immedi-
ately with clear water and contact a doctor as soon as possible.•
You should also consult a doctor without delay if you have inadvertently
swallowed coolant.
Caution
Do not continue your journey if for some reason it is not possible under the conditions prevailing to top up with coolant. Switch of the engine and contact

and obtain professional assistance from a specialist garage.
For the sake of the environment
Do not re-use coolant if it is necessary to
drain the coolant in the system. It should
be collected and disposed of in comp
liance with environmental protection
regulations.
se0.1.book Page 230 Frida
y, April 10, 2009 3:19 PM

Inspecting and replenishing
232
We recommend that you have the brake fluid replaced by a
Škoda Service Partner

as part of an Inspection Service.
WARNING
•
Using old brake fluid can result in seve
re stress on the brakes because of
the formation of vapour bubbles in the brake system. This greatly impairs the braking efficiency and thus also the safety of your vehicle.•
Brake fluid is toxic! It must therefore be kept safely in closed original
containers and well aw
ay from children and unauthorized persons.
Caution
Brake fluid damages the pa
intwork of the vehicle.
For the sake of the environment
In view of the problems involved with prop
er disposal of brake fluid, the special
tools and the professional knowledge required, you should have the brake fluid replaced by a Škoda Service Partner.BatteryWorking on the battery
The battery is located in the engine
compartment in a polyester cover or
in a plastic cover*. – Open the battery cover in direction of arrow
⇒
fig. 214
or press the
interlock on the side of the battery cover
⇒
fig. 215
, fold the cover up
and remove the battery.
– The installation of the battery cov
er takes place in the reverse order.
Removal and installation of the battery
is not recommended since it can, under
certain circumstances, lead to major
damage. Contact a specialist garage.
There is a risk of injuries, scalding, acci
dents and burns when carrying out any work
on the battery and on the electrical system. For this reason, it is essential to comply with the warning instructions
⇒
stated below and with the general applicable
rules of safety.
WARNING
•
The battery acid is strongly corros
ive and must, therefore, be handled
with the greatest of care. Always we
ar protective gloves, eye and skin
protection when handling batteries. Corrosive fumes in the air irritate the air passages and lead to conjunctivitis and inflammation of the air passages in the lungs. Battery acid corrodes dental enamel and creates deep wounds after contact with the skin which take a long time to heal. Repeated contact with diluted acids causes skin diseases (inflammations, ulcers, slin cracks).
Fig. 214 Engine compart- ment: Polyester cover of the vehicle battery
Fig. 215 Engine compart-ment: Plastic cover of the vehicle battery
se0.1.book Page 232 Frida
y, April 10, 2009 3:19 PM

Wheels and Tyres
243
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
cautious style of driving as the tyre is no
longer able to provide optimal grip and
handling in such a situation. This particul
arly important on wet roads. Please refer
to the notes
⇒page 247, “Spare wheel*”.
You should have the defective tyre replac
ed as soon as possible and restore the
correct direction of rotation on all tyresSnow chainsSnow chains must only be mounted on the front wheels. When driving on wintry roads, snow chains improve not only traction, but also the braking performance. For technical reasons, it is only permissi
ble to fit snow chains with the following
wheel/tyre combinations: Remove the
full wheel trims
if you wish to fit snow chains to the wheels.
Observe the national legal requirements relating to the maximum vehicle speed with snow chains.
WARNING
Please pay attention to the information in the supplied fitting instructions of the snow chain manufacturer.
Caution
You must take the chains off as soon as you drive on roads which are free of snow. They adversely affect the handling of your vehicle, damage the tyres and are rapidly destroyed.
Note
We recommend that you use snow chains
from the Škoda genuine accessories.
Wheel size
Depth (D)
Tyre s iz e
6J x 15
a)
a)Only fit snow chains with links an
d locks not larger than 15 mm.
47 mm
195/65
6.5J x 15
a)
50 mm
195/65
6J x 16
a)
50 mm
205/55
6J x 17
b)
b)Only fit snow chains with links
and locks not larger than 9 mm.
45 mm
205/50
se0.1.book Page 243 Frida
y, April 10, 2009 3:19 PM

Breakdown assistance
245
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Breakdown assistanceBreakdown assistanceFirst-aid box* and Warn
ing triangle* (Octavia)
The first-aid box* is attach
ed by a strap to the right-
hand side of the luggage
compartment The warning triangle can be at
tached to the trim panel of the rear wall with rubber
straps
⇒fig. 221
.
If you wish to equip your ve
hicle additionally with a warning triangle, please contact
a specialist garage.
Note
Pay attention to the use-by-date of the contents of the first-aid box.
First-aid box* and warning triangle* (Estate car)For vehicles of the type es
tate car the first-aid box and the warning triangle are
housed in a compartment on the right si
de in the luggage compartment. You can
open the compartment by turning the locks in the direction of arrow
⇒fig. 222
.
If you wish to equip your ve
hicle additionally with a warning triangle, please contact
a specialist garage.
Note
Pay attention to the use-by-date of
the contents of the first-aid box.
Fire extinguisher*The fire extinguisher is attached with straps in a holder under the driver seat. Please read carefully the
instructions which are atta
ched to the fire extin-
guisher.
Fig. 221 Placing of the warning triangle (Octavia)
Fig. 222 Placing of the warning triangle (Estate car)
se0.1.book Page 245 Frida
y, April 10, 2009 3:19 PM

Breakdown assistance
246
The fire extinguisher must
be checked by an authoris
ed person or company annu-
ally (please observe the differing legal requirements).
WARNING
If the fire extinguisher is not correc
tly attached, in case of sudden manoeu-
vres or an accident it can be “thrown” through the interior compartment and cause injuries.
Note
•
The fire extinguisher must comply with
the relevant and valid legal require-
ments.•
Pay attention to the expiration date of the fire extinguisher. If the fire extin-
guisher is used after the expiration date,
its proper function is
no longer assured.
•
The fire extinguisher is only supplied in
certain countries within the scope of
delivery.Vehicle tool kitThe vehicle tool kit and the lifting jack*, on which a note sticker is affixed, are stored in a box in the spare wheel*
⇒fig. 223
. There is also space here for the removable
ball for the trailer towing device*. The bo
x is attached with a strap on the spare
wheel. The vehicle tool kit contains
the following parts (depen
ding on equipment fitted):
•
Wire clamps for removing the full wheel trims,
•
Plastic clip for a wheel bolt cover,
•
Wheel wrench*,
•
To w i n g e y e ,
•
Adapter for the wheel bolts lock.*
•
Screwdriver* for removing the front fog lights
20).
After using the lifting jack*, screw in the arm of the lifting jack fully before placing it back in its storage area.
WARNING
•
The factory-supplied liftin
g jack* is only intended for your model of
vehicle. On no account attempt to lift a heavier vehicle or other loads - risk of injury!•
Ensure that the vehicle tool kit is
safely attached in the luggage compart-
ment.
Note
Ensure that the box is alwa
ys secured with the strap.
Tyre repair kit*The tyre repair kit is intended for the repair of minor tyre defects. The tyre repair kit contains a compressor, inflation bottle, operating instructions and accessories. The repair with the
tyre repair kit is
not at all intended to replace
a permanent
repair on the tyre, this repair only serves
to reach the next specialist garage. The
Fig. 223 Luggage compart- ment: storage compartment for vehicle tool kit
20)Valid for Octavia RS and Octavia Scout.
se0.1.book Page 246 Frida
y, April 10, 2009 3:19 PM