2009 Seat Exeo ST Owner's manual

If and when271
Safety First
Controls and equipment
Practical tips
Technical Data
Changing the side light bulb (inside of vehicle)
The procedure for changing the bulbs on the front
passenger's side is the same as on the driver's side.
– Switch off the ignition and the lights.
– Raise the bonnet.
– Move the brace ⇒fig. 214 in the direction of the arrow and
remove the rigid cover, separating the brace side and then
removing the two tabs from the other end of the cover.
– Remove the bulb and the bulb holder by pulling on the bulb holder wiring.
– Separate the bulb from the bulb holder by pulling both pieces anti-clockwise.
– Fit the new bulb by pressing on the bulb holder.
– Insert the bulb into the socket so that the side of the bulb holder grip is vertical ⇒fig. 215 and press on it.
– Fit the cover, first inserting the side tabs and then closing the cover and the brace. Make sure that the gasket sits well on the
casing cover during the operation.
– Check whether the new bulb is working.Changing bulbs. Bi-Xenon AFS headlightsTypes of bulbsYou must only replace a bulb with a bulb of the same type. The name can be
found on the base of the bulb.
Fig. 214 Side light bulb
(inside of vehicle)Fig. 215 Side lights. Bulb
holder grip in vertical
position
A1
ExeoST_EN.book Seite 271 Donnerstag, 3. September 2009 12:24 12

If and when
272
WARNING
•Take particular care when working on components in the engine
compartment if the engine is warm - risk of burns!•Bulbs are highly sensitive to pressure. The glass can break when you
touch the bulb, causing injury.•The high voltage element of gas discharge lamps* (xenon light) must
be handled correctly. Otherwise, there is a risk of death.•When changing bulbs, please take care not to injure yourself on sharp
parts in the headlight housing.Caution
•Remove the ignition key before working on the electric system. If not, a
short circuit could occur.•Switch off the lights or parking lights before you change a bulb.For the sake of the environment
Please ask your specialist retailer how to dispose of used bulbs in the proper
manner.
Note
•Depending on weather conditions (cold or wet), the front lights, the fog
lights, the rear lights and the indicators may be temporarily misted. This does not affect the useful life of the lighting system. By switching on the lights, the
area through which the beam of light is projected will quickly be demisted.
However, the edges may continue to be misted.
•Please check at regular intervals that all lighting (especially the exterior
lighting) on your vehicle is functioning properly. This is not only in the interest
of your own safety, but also in that of all other road users.•Before changing a bulb, make sure you have the correct new bulb.•Do not touch the glass part of the bulb with your bare hands, use a cloth
or paper towel instead. Otherwise, the fingerprints left on the glass will
vaporise as a result of the heat generated by the bulb, be deposited on the
reflector and impair its surface.Removing the air duct
The air duct has to be removed to gain access to the bulbs for
the right-side headlight.
Bulb
Type
Xenon bulbs
12 V/35 W (D1S)
DRL (day light)
12 V/21 W (P21W SLL)
Indicator light
12 V/21 W (PY21W)
Side lights
12 V/5 W (W5W blue LL)
Fig. 216 Air duct on right
side of vehicle
ExeoST_EN.book Seite 272 Donnerstag, 3. September 2009 12:24 12

If and when273
Safety First
Controls and equipment
Practical tips
Technical Data
–Unscrew bolts ⇒ page 272, fig. 216.
– Detach air duct from guide and take it out.Fitting the air duct
Once the bulb(s) for the right-side headlight have been
changed, the air duct must be re-installed.– Place the air duct in the correct position.
– First turn the two screws in lightly, then tighten both screws.
– Push air duct into guide .
Bi-Xenon AFS headlight bulbs
Indicator light
Xenon headlight (dipped-beam/main beam)
Side lights
DRL light (day light)
AA
AB
Fig. 217 Air duct on right
side of vehicle
AAAB
Fig. 218 Bi-Xenon AFS
headlight bulbs
AAABACAD
ExeoST_EN.book Seite 273 Donnerstag, 3. September 2009 12:24 12

If and when
274Changing the DRL light bulb (day light)
The procedure for changing the bulbs on the front
passenger's side is the same as on the driver's side.– Switch off the ignition and the lights.
– Raise the bonnet.
– Turn the bulb holder anti-clockwise, pulling it by the grip
⇒fig. 219 and removing the bulb holder and the bulb.
– Replace the blown bulb in the bulb holder (press and turn anti- clockwise to remove) with a new bulb (press and turn clockwise
to insert).
– Installation is in the reverse order. Note
Although it is not necessary, previously remove the rigid cover
⇒page 276,
fig. 222 for easier day light bulb changes.
Fig. 219 DRL light (day
light)
ExeoST_EN.book Seite 274 Donnerstag, 3. September 2009 12:24 12

If and when275
Safety First
Controls and equipment
Practical tips
Technical Data
Changing the turn signal bulb
The procedure for changing the bulbs on the front
passenger's side is the same as on the driver's side.
– Switch off the ignition and the lights.
– Raise the bonnet.
– Pull the rubber cap ⇒fig. 220 to remove it.
– Remove the bulb holder by pulling on the grip and turning it anti- clockwise ⇒fig. 221 .
– Replace the blown bulb in the bulb holder (press and turn anti- clockwise to remove) with a new bulb (press and turn clockwise
to insert).
– Insert the bulb holder into the socket with the tab facing upwards and the grip horizontal. Press it against the socket and turn
clockwise. When changing the bulb, you can check the position
of the bulb through the headlight glass.
– Fit the rubber cap and tighten, making sure it fit properly into the headlight casing.
– Check whether the new bulb is working.
Fig. 220 Indicator bulbFig. 221 Indicator bulb
ExeoST_EN.book Seite 275 Donnerstag, 3. September 2009 12:24 12

If and when
276Changing the side light bulb
The procedure for changing the bulbs on the front
passenger's side is the same as on the driver's side.
– Switch off the ignition and the lights.
– Raise the bonnet.
– Move the brace ⇒ fig. 222 in the direction of the arrow and
remove the rigid cover, separating the brace side and then
removing the two tabs from the other end of the cover.
– Remove the bulb holder by pulling on the grip ⇒fig. 223 (it can
also be removed by pulling on the bulb holder wires).
– Separate the bulb from the bulb holder by pulling both pieces anti-clockwise.
– Fit the new bulb by pressing on the bulb holder.
– Insert the bulb into the socket and press on the bulb holder grip.
– Fit the cover, first inserting the side tabs and then closing the cover and the brace. Make sure that the gasket sits well on the
casing cover during the operation.
– Check whether the new bulb is working.Changing the xenon bulbThe procedure for changing the bulbs on the front passenger's side is the
same as on the driver's side.
WARNING
This type of bulb should be changed at a qualified workshop.
Fig. 222 Side lightFig. 223 Side light
A1
ExeoST_EN.book Seite 276 Donnerstag, 3. September 2009 12:24 12

If and when277
Safety First
Controls and equipment
Practical tips
Technical Data
Changing bulbs for rear lights (in side panel)Overview of rear lightsRear lights in side panel•Brake lights and rear lights•Indicator light
Removing rear light
To change the bulbs you must remove the rear light assembly.
Removing the light requires a certain degree of practical skill.
F ig. 224 O ver vie w of rear
lights
Fig. 225 Luggage
compartment: Location of
the bolt securing the rear
lightFig. 226 Removing rear
light from side panel
ExeoST_EN.book Seite 277 Donnerstag, 3. September 2009 12:24 12

If and when
278
A special retaining screw is used to secure and guide the rear light.
– Check which of the bulbs is defective.
–Open the tailgate.
– Take the screwdriver out of the vehicle's tool kit ⇒ page 251.
– Use the flat-blade side of th e reversible screwdriver insert.
– Prise off the cover with a screwdriver in the slot ⇒page 277,
fig. 225 and remove the cover (with the retaining clips) from
the opening.
– Carefully loosen the screw located behind the cover with the screwdriver, turning it anti-clockwise (arrows) .
– Gradually ease the rear light out of the housing ( ⇒page 277,
fig. 226 positions and ) by pulling alternately in positions
and .
– Remove the bulb holder ⇒page 278.
CautionWhen removing or installing the rear light, take care not to cause any
damage.•Removing the rear light in particular can lead to the paintwork or rear light
becoming damaged. This is another reason why we recommend having the
bulbs changed by a qualified workshop.Note
Make sure you have a soft cloth ready to place under the glass on the rear
light, to avoid any scratches.
Removing the bulb holder
When changing a bulb, you must first remove the bulb holder.There are four securing tabs on the inside of the rear light unit.
– Release the retaining tabs ⇒fig. 227.
– Lift the bulb carrier off in the direction of the arrow .
– Change the defective bulb ⇒page 279.
A1
A2
A3
A4
A1
A2
Fig. 227 Retaining tabs
on reverse side of rear
light
AA
AB
ExeoST_EN.book Seite 278 Donnerstag, 3. September 2009 12:24 12