2009 SATURN VUE HYBRID display

Order of Play
Tracks recorded to the CD-R or
CD-RW are played in the following
order:
Play begins from the rst track in
the rst playlist and continues
sequentially through all tracks in
each playlist. When the last
track of the last playlist has
played, play continues from the
rst track of the rst playlist.
Play begins from the rst track in
the rst folder and continues
sequentially through all tracks in
each folder. When the last
track of the last folder has been
played, play continues from
the rst track of the rst folder.
When play enters a new folder, the
display does not automatically
show the new folder name unless
the folder mode is chosen as
the default display. The new track
name displays.File System and Naming
The song name that is displayed is
the song name that is contained
in the ID3 tag. If the song name is
not present in the ID3 tag, then
the radio displays the le name
without the extension (such as .mp3)
as the track name.
Track names longer than
32 characters or four pages are
shortened. Parts of words on the
last page of text and the extension
of the lename does not display.
Preprogrammed Playlists
Preprogrammed playlists that
were created by WinAmp™,
MusicMatch™, or Real Jukebox™
software can be accessed, however,
they cannot be edited using the
radio. These playlists are treated as
special folders containing
compressed audio song les.Playing an MP3
Insert a CD-R or CD-RW partway
into the slot (Single CD Player),
or press the
^button and wait for
the message to insert disc
(Six-Disc CD Player), label side up.
The player pulls it in, and the
CD-R or CD-RW should begin
playing.
If the ignition or radio is turned off
with a CD-R or CD-RW in the
player, it stays in the player. When
the ignition or radio is turned on,
the CD-R or CD-RW starts to
play where it stopped, if it was the
last selected audio source.
As each new track starts to play,
the track number and song title
displays.
ZEJECT:Press and release to
eject the CD-R or CD-RW that
is playing. A beep sounds
and Ejecting Disc displays. Once
the disc is ejected, Remove
Disc displays. The CD-R or CD-RW
can be removed. If the CD-R or
3-68 Instrument Panel
ProCarManuals.com

CD-RW is not removed, after
several seconds, the CD-R or
CD-RW automatically pulls back into
the player and begins playing.
For the Six-Disc CD player, press
and hold this button for two seconds
to eject all discs.
f(Tune):Turn to select MP3 les
on the CD-R or CD-RW currently
playing.
©SEEK¨:Press the left arrow
to go to the start of the current MP3
le, if more than ten seconds
have played. Press the right arrow
to go to the next MP3 le. If
either arrow is held or pressed
multiple times, the player continues
moving backward or forward
through MP3 les on the CD.
Sc(Previous Folder):Press
the pushbutton positioned under the
Folder label to go to the rst
track in the previous folder.
cT(Next Folder):Press the
pushbutton positioned under
the Folder label to go to the rst
track in the next folder.
sREV (Reverse):Press and
hold to reverse playback quickly
within an MP3 le. Sound is heard
at a reduced volume. Release
to resume playing the le. The
elapsed time of the le displays.
\FWD (Fast Forward):Press
and hold to advance playback
quickly within an MP3 le. Sound is
heard at a reduced volume.
Release to resume playing the le.
The elapsed time of the le
displays.RDM (Random):With the random
setting, the MP3 les on the
CD-R or CD-RW can be listened to
in random, rather than sequential
order, on one CD-R/CD-RW or
all discs in a six-disc CD player. To
use random, do one of the
following:
1. To play MP3 les from the CD-R
or CD-RW in random order,
press the pushbutton positioned
under the RDM label until
Random Current Disc displays.
Press the same pushbutton again
to turn off random play.
2. To play songs from all CDs
loaded in a six-disc CD player in
random order, press the
pushbutton positioned under the
RDM label until Randomize
All Discs displays. Press
the same pushbutton again to
turn off random play.
Instrument Panel 3-69
ProCarManuals.com

h(Music Navigator):Use the
music navigator feature to play MP3
les on the CD-R or CD-RW in order
by artist or album. Press the
pushbutton located below the music
navigator label. The player scans the
disc to sort the les by artist and
album ID3 tag information. It can
take several minutes to scan the disc
depending on the number of MP3
les recorded to the CD-R or
CD-RW. The radio can begin playing
while it is scanning the disc in the
background. When the scan is
nished, the CD-R or CD-RW begins
playing again.
Once the disc has been scanned, the
player defaults to playing MP3 les in
order by artist. The current artist
playing is shown on the second line
of the display between the arrows.
Once all songs by that artist are
played, the player moves to the next
artist in alphabetical order on the
CD-R/CD-RW and begins playing
MP3 les by that artist. To listen to
MP3 les by another artist, press the
pushbutton located below eitherarrow button. The disc goes to the
next or previous artist in alphabetical
order. Continue pressing either
button until the desired artist is
displayed.
To change from playback by artist to
playback by album, press the
pushbutton located below the Sort
By label. From the sort screen, push
one of the buttons below the album
button. Press the pushbutton below
the back label to return to the main
music navigator screen. Now the
album name is displayed on the
second line between the arrows and
songs from the current album begins
to play. Once all songs from that
album are played, the player moves
to the next album in alphabetical
order on the CD-R/CD-RW and
begins playing MP3 les from that
album.To exit music navigator mode, press
the pushbutton below the Back label
to return to normal MP3 playback.
BAND:Press to listen to the radio
while a CD is playing. The inactive
CD remains inside the radio for
future listening.
CD/AUX (CD/Auxiliary):Press to
play a CD while listening to the
radio. The CD icon and a message
showing disc and/or track number
displays while a CD is in the player.
Press this button again and the
system automatically searches for
an auxiliary input device such
as a portable audio player. If a
portable audio player is not
connected, “No Aux Input Device”
displays.
3-70 Instrument Panel
ProCarManuals.com

Fixed Mast Antenna
The xed mast antenna can
withstand most car washes without
being damaged as long as it is
securely attached to the base. If the
mast becomes slightly bent,
straighten it out by hand. If the mast
is badly bent, replace it.
Occasionally check to make sure
the antenna is tightened to its base.
If tightening is required, tighten
by hand.
XM™ Satellite Radio
Antenna System
The XM Satellite Radio antenna is
located on the roof of the vehicle.
Keep the antenna clear of
obstructions for clear radio
reception.
If the vehicle has a sunroof, the
performance of the XM system may
be affected if the sunroof is open.
Chime Level Adjustment
The radio may be used to adjust
the vehicle’s chime level. If the radio
can be used to change the volume
level of the chime, press and
hold the sixth FAV softkey with the
ignition on and the radio power
off. The volume level changes
between Normal and Loud. The
selected volume level appears on
the radio display.
Removing the radio and not
replacing it with a factory radio or
chime module will disable vehicle
chimes.
3-84 Instrument Panel
ProCarManuals.com

attempt to free it. SeeRocking Your
Vehicle to Get It Out on page 4-17
andIf Your Vehicle is Stuck in Sand,
Mud, Ice, or Snow on page 4-17for
more information.
The TCS/StabiliTrak
®button is
located on the instrument panel.
Press and release this button to turn
off TCS. The TCS warning light
will be displayed on the instrument
panel. The traction control system
can be turned back on by pressing
the TCS/StabiliTrak button.
If the system is limiting wheel spin
when the button is pressed, the
system will not turn off until there is
no longer a current need to limit
wheel spin. The system can
be turned back on at any time by
pressing the button again. If the
TCS light does not come on,TCS may not be functioning
properly and the vehicle should be
serviced at your dealer/retailer.
Adding non-dealer/non-retailer
accessories can affect the vehicle’s
performance. SeeAccessories
and Modifications on page 5-3for
more information.Steering
Electric Power Steering
If the engine stalls while driving, the
power steering assist system will
continue to operate until you
are able to stop the vehicle. If power
steering assist is lost because the
electric power steering system is not
functioning, the vehicle can be
steered but it will take more effort.
If you turn the steering wheel in
either direction several times until it
stops, or hold the steering wheel
in the stopped position for an
extended amount of time, you maynotice a reduced amount of power
steering assist. The normal
amount of power steering assist
should return shortly after a
few normal steering movements.
The electric power steering system
does not require regular
maintenance. If you suspect
steering system problems and/or the
Service Vehicle Soon light comes
on, contact your dealer/retailer
for service repairs.Steering Tips
It is important to take curves at a
reasonable speed.
Traction in a curve depends on the
condition of the tires and the
road surface, the angle at which the
curve is banked, and vehicle
speed. While in a curve, speed is
the one factor you can control.
If there is a need to reduce speed,
do it before entering the curve,
while the front wheels are straight.
Driving Your Vehicle 4-9
ProCarManuals.com

At the same time a message to
check the pressure in a specic tire
appears on the Driver Information
Center (DIC) display. The low tire
pressure warning light and the DIC
warning message come on at each
ignition cycle until the tires are
inated to the correct ination
pressure. Using the DIC, tire
pressure levels can be viewed by the
driver. For additional information and
details about the DIC operation and
displays seeDIC Operation and
Displays on page 3-36andDIC
Warnings and Messages on
page 3-42.
The low tire pressure warning light
may come on in cool weather
when the vehicle is rst started, and
then turn off as you start to drive.
This could be an early indicator that
the air pressure in the tire(s) are
getting low and need to be inated
to the proper pressure.A Tire and Loading Information label
shows the size of your vehicle’s
original equipment tires and
the correct ination pressure for
your vehicle’s tires when they
are cold. SeeLoading the Vehicle
on page 4-18, for an example of the
Tire and Loading Information
label and its location on your
vehicle. Also seeInflation - Tire
Pressure on page 5-43.
Your vehicle’s TPMS system can
warn you about a low tire pressure
condition but it does not replace
normal tire maintenance. SeeTire
Inspection and Rotation on
page 5-50andTires on page 5-38.Notice:Using non-approved tire
sealants could damage the
Tire Pressure Monitor System
(TPMS) sensors. TPMS sensor
damage caused by using an
incorrect tire sealant is not
covered by the vehicle warranty.
Always use the GM approved
tire sealant available through your
dealer/retailer.
Your vehicle, when new, included a
factory-installed Tire Inator Kit.
This kit uses a GM approved liquid
tire sealant. Using non-approved
tire sealants could damage the
TPMS sensors. See Tire Sealant
and Compressor Kit for information
regarding the inator kit materials
and instructions.
Service and Appearance Care 5-47
ProCarManuals.com

TPMS Malfunction Light and
Message
The TPMS will not function properly if
one or more of the TPMS sensors
are missing or inoperable. When the
system detects a malfunction, the
low tire warning light ashes for
about one minute and then stays on
for the remainder of the ignition
cycle. A DIC warning message is
also displayed. The low tire warning
light and DIC warning message
come on at each ignition cycle until
the problem is corrected. Some of
the conditions that can cause the
malfunction light and DIC message
to come on are:
The TPMS sensor matching
process was started but not
completed or not completed
successfully after rotating the
vehicle’s tires. The DIC message
and TPMS malfunction light
should go off once the TPMS
sensor matching process is
performed successfully. See
“TPMS Sensor Matching Process”
later in this section.
One or more TPMS sensors are
missing or damaged. The DIC
message and the TPMS
malfunction light should go
off when the TPMS sensors
are installed and the sensor
matching process is performed
successfully. See your dealer/
retailer for service.
Replacement tires or wheels do
not match your vehicle’s original
equipment tires or wheels. Tires
and wheels other than those
recommended for your vehicle
could prevent the TPMS from
functioning properly. SeeBuying
New Tires on page 5-51.
Operating electronic devices or
being near facilities using radio
wave frequencies similar to the
TPMS could cause the TPMS
sensors to malfunction.
If the TPMS is not functioning it
cannot detect or signal a low tire
condition. See your dealer/retailer for
service if the TPMS malfunction light
and DIC message comes on and
stays on.
TPMS Sensor Matching
Process
Each TPMS sensor has a unique
identication code. Any time
you replace one or more of the
TPMS sensors or rotate the
vehicle’s tires, the identication
codes need to be matched to the
new tire/wheel location. The sensors
are matched, to the tire/wheel
locations, in the following order:
driver side front tire, passenger side
front tire, passenger side rear
tire, and driver side rear tire using a
TPMS diagnostic tool. See your
dealer/retailer for service.
The TPMS sensors can also be
matched to each tire/wheel position
by increasing or decreasing the
tire’s air pressure. When increasing
the tire’s pressure, do not exceed
the maximum ination pressure
indicated on the tire’s sidewall. To
decrease the tire’s air-pressure
use the pointed end of the valve
cap, a pencil-style air pressure
gage, or a key.
5-48 Service and Appearance Care
ProCarManuals.com

When you go to your dealer/retailer
for service, trained and supported
service technicians will perform
the work using genuine parts.
To purchase service information,
seeService Publications Ordering
Information on page 7-13.
Owner Checks and Services on
page 6-8tells what should be
checked, when to check it, and what
can easily be done to help keep
the vehicle in good condition.
The proper replacement parts,
uids, and lubricants to use
are listed inRecommended Fluids
and Lubricants on page 6-11
andMaintenance Replacement
Parts on page 6-12. When the
vehicle is serviced, make sure these
are used. All parts should be
replaced and all necessary repairs
done before you or anyone else
drives the vehicle. We recommend
the use of genuine parts from
your dealer/retailer.Scheduled Maintenance
When the Change Engine Oil
light displays, service is required for
the vehicle. Have the vehicle
serviced as soon as possible within
the next 600 miles (1 000 km). It
is possible that, if driving under the
best conditions, the engine oil
life system may not indicate that
vehicle service is necessary for over
a year. However, the engine oil
and lter must be changed at least
once a year and at this time the
system must be reset. Your
dealer/retailer has trained service
technicians who will perform
this work using genuine parts and
reset the system.If the engine oil life system is ever
reset accidentally, service the
vehicle within 3,000 miles
(5 000 km) since the last service.
Remember to reset the oil life
system whenever the oil is changed.
SeeEngine Oil Life System on
page 5-14for information on
the Engine Oil Life System and
resetting the system.
When the Change Engine Oil light
appears, certain services, checks,
and inspections are required.
Required services are described in
the following for “MaintenanceI”
and “MaintenanceII.” Generally, it is
recommended that the rst service
be MaintenanceI, the second
service be MaintenanceII, and then
alternate MaintenanceIand
MaintenanceIIthereafter. However,
in some cases, MaintenanceII
may be required more often.
Maintenance Schedule 6-3
ProCarManuals.com