2009 SATURN VUE HYBRID display

Driver Information
Center (DIC)
Your vehicle has a Driver
Information Center (DIC).
All information appears in the DIC
display located in the instrument
panel cluster.
The DIC comes on when the
ignition is on. After a short delay,
the DIC displays the information that
was last displayed before the
engine was turned off.
The DIC displays trip, fuel, and
vehicle system information, and
warning messages if a system
problem is detected.
The DIC also displays the compass
direction, outside air temperature,
and shift position indicator at the top
of the DIC display. If there is a
problem with the system that controls
the temperature display, the
numbers will be replaced with
dashes. If this occurs, have the
vehicle serviced by your dealer/retailer. If an abnormal temperature
reading is displayed for an
extended period of time, consult
your dealer/retailer. Under certain
circumstances, especially when the
engine is idling, a delay updating the
temperature display is normal.
SeeDIC Compass on page 3-40
andAutomatic Transmission
Operation on page 2-20for more
information.
DIC Operation and
Displays
The DIC has different displays
which can be accessed by pressing
the DIC buttons located on the
instrument panel, below the
headlamp switch.
The DIC displays trip, fuel, and
vehicle system information, and
warning messages if a system
problem is detected.The DIC also allows some features
to be customized. SeeDIC Vehicle
Customization on page 3-49for more
information.
DIC Buttons
The buttons are the trip/fuel, vehicle
information, customization, and
set/reset buttons. The button
functions are detailed in the
following pages.
3(Trip/Fuel):Press this button
to display the odometer, trip
odometer, fuel range, average
economy, and instantaneous
economy. The compass and outside
temperature will also be shown in
the display. The temperature will be
shown in °F or °C depending on
the units selected.
3-36 Instrument Panel
ProCarManuals.com

T(Vehicle Information):Press
this button to display the oil life,
units, tire pressure readings
for vehicles with the Tire Pressure
Monitor System (TPMS), Remote
Keyless Entry (RKE) transmitter
programming, economy light on/off,
compass zone setting, and
compass recalibration on vehicles
with this feature.
U(Customization):Press this
button to customize the feature
settings on your vehicle. SeeDIC
Vehicle Customization on page 3-49
for more information.
V(Set/Reset):Press this button to
set or reset certain functions and
to turn off or acknowledge
messages on the DIC.
Trip/Fuel Menu Items
3(Trip/Fuel):Press this button
to scroll through the following
menu items:
Odometer
Press the trip/fuel button until
ODOMETER displays. This display
shows the distance the vehicle
has been driven in either miles (mi)
or kilometers (km). Pressing the
trip odometer reset stem will
also display the odometer.
To switch between English and
metric measurements, see “Units”
later in this section.
Trip Odometer
Press the trip/fuel button until TRIP
displays. This display shows the
current distance traveled in
either miles (mi) or kilometers (km)
since the last reset for the trip
odometer. Pressing the trip
odometer reset stem will also
display the trip odometer.The trip odometer can be reset to
zero by pressing the set/reset button
while the trip odometer is displayed.
You can also reset the trip
odometer while it is displayed by
pressing and holding the trip
odometer reset stem.
Fuel Range
Press the trip/fuel button until
FUEL RANGE displays. This
display shows the approximate
number of remaining miles (mi) or
kilometers (km) the vehicle can be
driven without refueling. The display
will show LOW if the fuel level is low.
The fuel range estimate is based on
an average of the vehicle’s fuel
economy over recent driving history
and the amount of fuel remaining
in the fuel tank. This estimate
will change if driving conditions
change. For example, if driving in
traffic and making frequent
stops, this display may read one
number, but if the vehicle is driven
on a freeway, the number may
change even though the same
Instrument Panel 3-37
ProCarManuals.com

amount of fuel is in the fuel tank.
This is because different driving
conditions produce different
fuel economies. Generally, freeway
driving produces better fuel
economy than city driving. Fuel
range cannot be reset.
If the vehicle is low on fuel, the
FUEL LEVEL LOW message will be
displayed. See “FUEL LEVEL
LOW” underDIC Warnings and
Messages on page 3-42.
Average Fuel Economy
Press the trip/fuel button until
AVERAGE FUEL ECONOMY
displays. This display shows the
approximate average miles per
gallon (mpg) or liters per
100 kilometers (L/100 km). This
number is calculated based on the
number of mpg (L/100 km)
recorded since the last time this
menu item was reset. To reset the
AVERAGE FUEL ECONOMY,
press and hold the set/reset button.
The display will show zero.Instantaneous Fuel Economy
If the vehicle has this display, press
the trip/fuel button until INSTANT
FUEL ECONOMY displays.
This display shows the current fuel
economy at a particular moment
and will change frequently as driving
conditions change. This display
shows the instantaneous fuel
economy in miles per gallon (mpg)
or liters per 100 kilometers
(L/100 km). Unlike average fuel
economy, this display cannot
be reset.
Blank Display
This display shows no information.Vehicle Information Menu
Items
T(Vehicle Information):Press
this button to scroll through the
following menu items:
Oil Life
Press the vehicle information button
until OIL LIFE REMAINING
displays. This display shows an
estimate of the oil’s remaining useful
life. If you see 99% OIL LIFE
REMAINING on the display, that
means 99% of the current oil
life remains. The engine oil life
system will alert you to change the
oil on a schedule consistent with
your driving conditions.
When the remaining oil life is low,
the CHANGE ENGINE OIL
SOON message will appear on the
display. See “CHANGE ENGINE
OIL SOON” underDIC Warnings
and Messages on page 3-42.
You should change the oil as soon
as you can. SeeEngine Oil on
page 5-11. In addition to the engine
3-38 Instrument Panel
ProCarManuals.com

oil life system monitoring the
oil life, additional maintenance is
recommended in the Maintenance
Schedule in this manual. See
Scheduled Maintenance on page 6-3
for more information.
Units
Press the vehicle information button
until UNITS displays. This display
allows you to select between English
or Metric units of measurement.
Once in this display, press the
set/reset button to select between
ENGLISH or METRIC units. All
of the vehicle information will then
be displayed in the unit of
measurement selected.
Tire Pressure
If your vehicle has the Tire Pressure
Monitor System (TPMS), the
pressure for each tire can be viewed
in the DIC. The tire pressure will
be shown in either pounds per
square inch (psi) or kilopascals
(kPa). Press the vehicle information
button until the DIC displaysFRONT TIRES PSI (kPa) LEFT ##
RIGHT ##. Press the vehicle
information button again until the
DIC displays REAR TIRES PSI
(kPa) LEFT ## RIGHT ##.
If a low or high tire pressure
condition is detected by the system
while driving, a message advising
you to check the pressure in a
specic tire will appear in the
display. SeeInflation - Tire Pressure
on page 5-43andDIC Warnings
and Messages on page 3-42
for more information.
If the tire pressure display shows
dashes instead of a value, there
may be a problem with your vehicle.
If this consistently occurs, see
your dealer/retailer for service.Relearn Remote Key
This display allows you to match
Remote Keyless Entry (RKE)
transmitters to your vehicle. To
match an RKE transmitter to your
vehicle:
1. Press the vehicle information
button until PRESS
VTO
RELEARN REMOTE KEY
displays.
2. Press the set/reset button until
REMOTE KEY LEARNING
ACTIVE is displayed.
3. Press and hold the lock and
unlock buttons on the rst
transmitter at the same time for
about 15 seconds.
A chime will sound indicating
that the transmitter is matched
and REMOTE KEY LEARNING
COMPLETE will be shown
on the display.
Instrument Panel 3-39
ProCarManuals.com

4. To match additional transmitters
at this time, repeat Step 3.
Each vehicle can have a
maximum of eight transmitters
matched to it.
5. To exit the programming mode,
you must cycle the key to
LOCK/OFF.
Compass Zone Setting
This display allows for setting the
compass zone. SeeDIC Compass
on page 3-40for more information.
Compass Recalibration
This display allows for calibrating
the compass. SeeDIC Compass on
page 3-40for more information.
ECO (Economy) Light On/Off
This display allows you to turn the
ECO light in the cluster on and
off. SeeFuel Economy Light
on page 3-35for more information.
Press the vehicle information
button until PRESS
VSET ECO
displays. This display will onlybe available when the vehicle is in
P (Park). Once in the display,
press the set/reset button to select
ON or OFF.
Blank Display
This display shows no information.
DIC Compass
Your vehicle may have a
compass in the Driver Information
Center (DIC).
Compass Zone
The zone is set to zone eight upon
leaving the factory. Your dealer/
retailer will set the correct zone for
your location.
Under certain circumstances, such
as during a long distance
cross-country trip or moving to a
new state or province, it will
be necessary to compensate for
compass variance by resetting the
zone through the DIC if the zone
is not set correctly.Compass variance is the difference
between the earth’s magnetic
north and true geographic north. If
the compass is not set to the
zone where you live, the compass
may give false readings. The
compass must be set to the variance
zone in which the vehicle is
traveling.
To adjust for compass variance, use
the following procedure:
Compass Variance (Zone)
Procedure
1. Do not set the compass zone
when the vehicle is moving.
Only set it when the vehicle is in
P (Park).
Press the vehicle information
button until PRESS
VTO SET
COMPASS ZONE: ## displays.
3-40 Instrument Panel
ProCarManuals.com

2. Find the vehicle’s current
location and variance zone
number on the map.
Zones 1 through 15 are
available.
3. Press and hold the set/reset
button to scroll through and
select the appropriate
variance zone.
4. Press the trip/fuel button until the
vehicle heading, for example,
N for North, is displayed in
the DIC.5. If calibration is necessary,
calibrate the compass. See
“Compass Calibration Procedure”
following.
Compass Calibration
The compass can be manually
calibrated. Only calibrate the
compass in a magnetically clean
and safe location, such as an open
parking lot, where driving the
vehicle in circles is not a danger. It
is suggested to calibrate away
from tall buildings, utility wires,
manhole covers, or other industrial
structures, if possible.
If CAL should ever appear in the
DIC display, the compass should be
calibrated.
If the DIC display does not show a
heading, for example, N for
North, or the heading does not
change after making turns, there
may be a strong magnetic eld
interfering with the compass. Such
interference may be caused by
a magnetic CB or cell phoneantenna mount, a magnetic
emergency light, magnetic note pad
holder, or any other magnetic
item. Turn off the vehicle, move the
magnetic item, then turn on the
vehicle and calibrate the compass.
To calibrate the compass, use
the following procedure:
Compass Calibration Procedure
1. Before calibrating the compass,
make sure the compass is set
to the variance zone in which the
vehicle is located. See
“Compass Variance (Zone)
Procedure” earlier in this section.
Do not operate any switches
such as window, sunroof, climate
controls, seats, etc. during the
calibration procedure.
2. Press the vehicle information
button until PRESS
VTO
CALIBRATE COMPAS
(Compass) displays.
Instrument Panel 3-41
ProCarManuals.com

3. Press the set/reset button to start
the compass calibration.
4. The DIC will display
CALIBRATING COMPASS:
TURN IN CIRCLES. Drive the
vehicle in tight circles at less than
5 mph (8 km/h) to complete the
calibration. The DIC will display
COMPASS CALIBRATION
COMPLETE for a few seconds
when the calibration is complete.
The DIC display will then return to
the previous menu.
DIC Warnings and
Messages
Messages are displayed on the DIC
to notify the driver that the status
of the vehicle has changed and that
some action may be needed by
the driver to correct the condition.
Multiple messages may appear one
after another.
Some messages may not require
immediate action, but you can press
any of the DIC buttons, or the trip
odometer reset stem on theinstrument panel cluster to
acknowledge that you received the
messages and to clear them
from the display.
Some messages cannot be cleared
from the DIC display because they
are more urgent. These messages
require action before they can be
cleared. Take any messages that
appear on the display seriously and
remember that clearing the
messages will only make the
messages disappear, not correct the
problem.
The following are the possible
messages that can be displayed
and some information about them.
BATTERY SAVER ACTIVE
This message displays when
the charging system detects that the
battery is being drained. You may
notice that the vehicle attempts
to reduce the drain for you by
turning off accessories, such as
interior fans, rear defogger,
and heated seats. Turn off allaccessories. If the vehicle is not
running, start and run the engine for
at least 10 minutes to allow the
battery to recharge. If the engine is
running and the condition persists,
see your dealer/retailer immediately.
CALIBRATING COMPASS:
TURN IN CIRCLES
This message displays when
calibrating the compass. Drive the
vehicle in circles at less than
5 mph (8 km/h) to complete the
calibration. SeeDIC Compass on
page 3-40.
CHANGE ENGINE OIL SOON
This message displays when service
is required for the vehicle. See
your dealer/retailer. SeeEngine Oil
on page 5-11andScheduled
Maintenance on page 6-3for more
information.
3-42 Instrument Panel
ProCarManuals.com

Acknowledging this message will
not reset the OIL LIFE REMAINING
display. That must be done at
the OIL LIFE screen. See “OIL LIFE”
underDIC Operation and Displays
on page 3-36andEngine Oil
Life System on page 5-14for more
information.
CHANGE TRANSMISSION
FLUID
Notice:Use of the incorrect
automatic transmission uid may
damage the vehicle, and the
damages may not be covered by
the vehicle’s warranty. Always
use the automatic transmission
uid listed inRecommended
Fluids and Lubricants on
page 6-11.
This message displays when the life
of the transmission uid has
expired and it should be changed.
SeeScheduled Maintenance
on page 6-3andRecommended
Fluids and Lubricants on page 6-11
for the proper uid and change
intervals.
CHECK TIRE PRESSURE
On vehicles with the Tire Pressure
Monitor System (TPMS), this
message displays when the
pressure in one or more of the
vehicle’s tires needs to be checked.
This message also displays LEFT
FRONT, RIGHT FRONT, LEFT
REAR, or RIGHT REAR to indicate
which tire needs to be checked.
You can receive more than one tire
pressure message at a time. To
read the other messages that may
have been sent at the same
time, press the set/reset button. If a
tire pressure message appears
on the DIC, stop as soon as
you can. Have the tire pressures
checked and set to those shown on
the Tire Loading Information
label. SeeTires on page 5-38,
Loading the Vehicle on page 4-18,
andInflation - Tire Pressure on
page 5-43. The DIC also shows the
tire pressure values. SeeDIC
Operation and Displays on
page 3-36. If the tire pressure islow, the low tire pressure warning
light comes on. SeeTire Pressure
Light on page 3-29.
COMPASS CALIBRATION
COMPLETE
This message displays when the
compass calibration is complete.
SeeDIC Compass on page 3-40.
CRUISE CONTROL SET
TO XXX
This message displays whenever
the cruise control is set. SeeCruise
Control on page 3-9for more
information.
DRIVER DOOR OPEN
This message displays when the
driver door is not closed properly.
Close the door completely.
Instrument Panel 3-43
ProCarManuals.com