2009 RENAULT TWINGO Sequential Transmission Workshop Manual

21B-89
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET048
DRIVER'S DOOR STATUSES DETECTION
STATUS
DEFINITIONThis status indicates detection by the sequential gearbox computer of the driver's door
and has the specification "DONE" or "NOT DONE".
NOTESNone
Engine stopped, ignition on
ET048: "DONE"
In the event of a fault, refer to the interpretation of status ET027 "Driver's door open".
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET048

21B-90
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET049
HANDBRAKE POSITION RECOGNITION
STATUS
DEFINITIONThis status indicates detection by the sequential gearbox computer of the handbrake
position and has the specification "DONE" or "NOT DONE".
NOTESNone
Engine stopped, ignition on
ET049: "DONE"
In the event of a fault, refer to the interpretation of status ET028 “Handbrake”.
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET049

21B-91
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET053
VEHICLE SPEED SIGNAL DETECTION
STATUS
DEFINITIONThis status indicates detection by the sequential gearbox computer of the vehicle speed
and has the specification "DONE" or "NOT DONE".
NOTESNone
Engine stopped, ignition on
ET053: "DONE"
In the event of a fault, refer to the interpretation of the following faults:
●DF176 "Front right-hand wheel speed multiplex signal",
●DF175 "Front left-hand wheel speed multiplex signal",
●DF117 "Rear left-hand wheel speed multiplex signal",
●DF118 "Rear right-hand wheel speed multiplex signal".
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET053

21B-92
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET054
PUMP RELAY CONTROL
STATUS
DEFINITIONACTIVE: indicates that the pump is supplied to increase the pressure in the hydraulic
circuit.
INACTIVE: indicates that the pump is not being actuated.
NOTESNone
Engine running at idle speed
If parameter PR018 "Hydraulic pressure" is below 40 bar, ET054 is "ACTIVE" until PR018 = 50 bar is reached.
If parameter PR018 "Hydraulic pressure" is above 40 bar, ET054 is "INACTIVE".
In the event of a fault, refer to the interpretation of fault DF252 “Pump relay”.
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET054

21B-93
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET055
STARTER RELAY CONTROL
STATUS
DEFINITIONThis signal indicates the status of the starter control circuit and has the specification
"ACTIVE" or "INACTIVE".
NOTESNone
Engine stopped, ignition on
INACTIVE
"ACTIVE" when the starter is operating.
In the event of a fault, perform fault finding on the UCH (see 87B, Passenger compartment connection unit).
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET055

21B-94
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET056
CLUTCH SOLENOID VALVE CONTROL
STATUS
DEFINITIONThis signal indicates the status of the clutch solenoid valve and has the specification
"ACTIVE" or "INACTIVE".
NOTESNone
Engine stopped, ignition on
INACTIVE: engine stopped
In the event of a fault, consult the interpretation of fault DF071 “Clutch solenoid valve circuit”.
Engine warm at idle speed
INACTIVE: engine running
ACTIVE: when a gear is being selected
In the event of a fault, consult the interpretation of fault DF071 “Clutch solenoid valve circuit”.
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET056

21B-95
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET057
ENGAGEMENT SOLENOID VALVE 1 CONTROL
STATUS
DEFINITIONThis signal indicates the status of the control circuit of engagement solenoid valve 1 and
has the specification "ACTIVE" or "INACTIVE".
NOTESNone
Engine stopped, ignition on
INACTIVE, engine stopped
In the event of a fault, consult the interpretation of fault DF072 “Engagement solenoid valve 1 circuit”.
Engine warm at idle speed
INACTIVE, engine running, vehicle stopped
ACTIVE when each gear is selected
In the event of a fault, consult the interpretation of fault DF072 “Engagement solenoid valve 1 circuit”.
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET057

21B-96
MR-413-X44-21B000$649.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of statuses
Vdiag No: 04
21B
ET058
ENGAGEMENT SOLENOID VALVE 2 CONTROL
STATUS
DEFINITIONThis signal indicates the status of the control circuit of engagement solenoid valve 2 and
has the specification "ACTIVE" or "INACTIVE".
NOTESNone
Engine stopped, ignition on
INACTIVE, engine stopped
In the event of a fault, consult the interpretation of fault DF073 “Engagement solenoid valve 2 circuit”.
Engine warm at idle speed
INACTIVE, engine running, vehicle stopped
ACTIVE when each gear is selected
In the event of a fault, consult the interpretation of fault DF073 “Engagement solenoid valve 2 circuit”.
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
BVRJH1_V04_ET056