2009 RENAULT TWINGO RS Trim And Upholstery Workshop Manual

71A-14
BODY INTERNAL TRIM
Rear panel lining: Removal - Refitting
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPull the rear seats down or remove the rear bench
seatback (depending on equipment level) (see 76A,
Rear seat frames and mechanisms, Rear bench
seatback: Removal - Refitting, page 76A-5) .
aRemove the rear parcel shelf side trim (see 71A,
Body internal trim, Rear parcel shelf side trim:
Removal - Refitting, page 71A-15) .
aPartially remove the front side door seal.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the clip (1) .aRemove the bolt (2) .
aUnclip the rear panel trim.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aFit the rear panel trim.
aRefit:
-the bolt (2) ,
-the clip (1) .
II - FINAL OPERATION.
aRefit:
-the front side door seal,
-the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-15) .
aPull the rear seats down or refit the rear bench seat-
back (depending on equipment level) (see 76A,
Rear seat frames and mechanisms, Rear bench
seatback: Removal - Refitting, page 76A-5) .
121069
121075

71A-15
BODY INTERNAL TRIM
Rear parcel shelf side trim: Removal - Refitting
71A
REMOVAL
OPERATION FOR REMOVAL OF PART
CONCERNED
aPartially remove the tailgate seal.
aRemove the bolts (1) .
aDetach the rear parcel shelf side trim.
aDisconnect the luggage compartment light.
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aConnect the luggage compartment light.
aClip on the rear parcel shelf side trim.
aRefit:
-the bolts (1) ,
-the tailgate seal.
121066

71A-16
BODY INTERNAL TRIM
Rear loading trim: Removal - Refitting
G44
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the clips (1) ,
-the rear parcel shelf (2) ,
-the luggage compartment carpet.aTilt the front seat backrest.
aRemove:
-the bolts (3) ,
-the partition panel.
aPartially remove the tailgate seal.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the bolts (4) ,
122850
122849
122845

71A-17
BODY INTERNAL TRIM
Rear loading trim: Removal - Refitting
G44
71A
-the retaining hooks.
aRemove:
-the bolts (5) ,
-the clip (6) .
aRemove:
-the bolts (7) ,
-the rear panel trim,
-the rear floor attached to the front section (see
Raised rear floor, front section: Removal - Re-
fitting) (MR 412, 41D, Rear lower structure).REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the rear floor attached to the front section (see
Raised rear floor, front section: Removal - Re-
fitting) (MR 412, 41D, Rear lower structure),
-the rear panel trim,
-the bolts (7) ,
-the clip (6) ,
-the bolts (5) ,
-the retaining hooks,
-the bolts (4) .
II - FINAL OPERATION.
aRefit:
-the tailgate seal,
-the partition,
-the bolts (3) ,
-pull down the front seat backrest,
-the luggage compartment carpet,
-the rear parcel shelf (2) ,
-the clips (1) .
122846
122853

72A-1
SIDE OPENING ELEMENT TRIM
Front side door trim: Removal - Refitting
72A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aUnclip door mirror trim.
aRemove (depending on equipment level):
-the cover (1) ,
-the bolt (2) .aRemove (depending on equipment level):
-the clip (3) using a screwdriver,
-the front side door manual window winder handle.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the bolt (4) .
119276
119497
124797
119274

72A-2
SIDE OPENING ELEMENT TRIM
Front side door trim: Removal - Refitting
72A
aRemove the bolts (5) .
aUnclip:
-the front side door trim using a pair of unclipping
pliers (protect the door box section),
-the interior door handle cable using a flat-blade
screwdriver.
aDisconnect the supply connectors (depending on
equipment level).
REFITTING
I - REFITTING PREPARATIONS OPERATION
aReplace the clips on the front side door trim if neces-
sary.
II - REFITTING OPERATION FOR PART
CONCERNED
aConnect the supply connectors (depending on equi-
pment level).
aClip on:
-the interior door handle cable,
-the front side door trim.
aRefit:
-the bolts (5) ,
-the bolt (4) .III - FINAL OPERATION.
aRefit (depending on equipment level):
-the bolt (2) ,
-the cover (1) ,
-the front side door manual window winder handle,
-the clip (3) using a screwdriver.
aClip on the door mirror trim piece.
aCarry out a function test.
119277

73A-1
NON-SIDE OPENING ELEMENTS TRIM
Tailgate trim: Removal - Refitting
73A
REMOVAL
OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the bolt (1) .
aUnclip the tailgate trim.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aReplace the tailgate trim clips if necessary.
II - REFITTING OPERATION FOR PART
CONCERNED
aClip the tailgate trim in place.
aRefit the bolt (1) .
119287

75A-1
FRONT SEAT FRAMES AND MECHANISMS
Front seat base frame: Removal - Refitting
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the compete front seat (see 75A, Front seat fra-
mes and mechanisms, Complete front seat: Re-
moval - Refitting, page 75A-8) ,
-the front seatback trim (see 77A, Front seat trim,
Front seatback trim: Removal - Refitting, page
77A-4) ,
-the front seat cushion trim (see 77A, Front seat
trim, Front seat base trim: Removal - Refitting,
page 77A-1) ,
-the front side (chest-level) airbag (depending on
the equipment level) (see Front (chest-level) side
airbag: Removal - Refitting) (MR 411, 88C, Air-
bags and seat belt pretensioners),
-the front buckle pretensioner (see Front buckle
pretensioner: Removal - Refitting) (MR 411,
88C, Airbags and seat belt pretensioners).II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the front seatback frame (see 75A, Front seat fra-
mes and mechanisms, Front seatback frame:
Removal - Refitting, page 75A-2) ,
-the front seat runners (see 75A, Front seat frames
and mechanisms, Front seat runner: Removal -
Refitting, page 75A-6) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the front seatback frame (see 75A, Front seat fra-
mes and mechanisms, Front seatback frame:
Removal - Refitting, page 75A-2) ,
-the front seat runners (see 75A, Front seat frames
and mechanisms, Front seat runner: Removal -
Refitting, page 75A-6) .
II - FINAL OPERATION.
aRefit:
-the front buckle pretensioner (see Front buckle
pretensioner: Removal - Refitting) (MR 411,
88C, Airbags and seat belt pretensioners),
-the front side (chest-level) airbag (depending on
the equipment level) (see Front (chest-level) side
airbag: Removal - Refitting) (MR 411, 88C, Air-
bags and seat belt pretensioners),
-the front seat cushion trim (see 77A, Front seat
trim, Front seat base trim: Removal - Refitting,
page 77A-1) ,
-the front seatback trim (see 77A, Front seat trim,
Front seatback trim: Removal - Refitting, page
77A-4) ,
-the entire front seat (see 75A, Front seat frames
and mechanisms, Complete front seat: Remo-
val - Refitting, page 75A-8) .
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (MR 413, 88C, Airbags and seat belt preten-
sioners). Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.