2009 RENAULT TWINGO RS light

62B-44
MR-413-X44-62B000$506_eng.mif
V1
CLIMATE CONTROL
Fault finding - Status summary table

Vdiag No.: 44
62B
ET020
COMPRESSOR CONTROL
NOTESNone
This indicates the status of the compressor actuated by the injection computer.
If ET020 displays ACTIVE, the compressor activation request is authorised.
If ET020 displays INACTIVE, the compressor activation request is not authorised.
If the “AC” indicator light is lit and if ET020 displays INACTIVE, run fault finding on the injection computer
(see 13B, Diesel injection or 17B, Petrol injection) and UCH (see 87B, UCH).
AFTER REPAIRRepeat the conformity check from the start.
CLIM_V44_ET020

62B-51
MR-413-X44-62B000$598_eng.mif
V1
62B
CLIMATE CONTROL
Fault finding - Parameter summary table
Tool parameter Diagnostic tool title
PR001Interior temperature
PR002External temperature
PR004Coolant temperature
PR011Distribution flap position
PR012Mixing flap position
PR019Passenger compartment PWM* setting
PR045Current heating* resistor power
PR092Battery voltage
PR122Night lighting level

Vdiag No.: 44
MR-413-X44-62B000$598_eng.mif

62B-60
MR-413-X44-62B000$644_eng.mif
V1
CLIMATE CONTROL
Fault finding - Interpretation of parameters
Vdiag No.: 44
62B
PR122
NIGHT LIGHTING LEVEL
NOTESThe climate control computer receives the dimmer lighting level via the instrument
panel through the multiplex line.
This parameter indicates the dimmer lighting level as a percentage.
If this parameter appears inconsistent with the air conditioning control panel lighting, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.
CLIM_V44_PR122

62B-67
MR-413-X44-62B000$782_eng.mif
V1
CLIMATE CONTROL
Fault finding - Customer complaints62B
PASSENGER COMPARTMENT ODOURS
UNPLEASANT ODOURS IN PASSENGER COMPARTMENT ALP 11
WATER IN PASSENGER COMPARTMENT
WATER IS PRESENT IN PASSENGER COMPARTMENT ALP 12
CONTROL PANEL FAULT
NO CONTROL PANEL LIGHTING ALP 13
COMPRESSOR NOISES
COMPRESSOR NOISES ALP 14

62B-71
MR-413-X44-62B000$828_eng.mif
V1

Vdiag No.: 44CLIMATE CONTROL
Diagnostic - Fault finding chart62B
ALP 2
CONTINUED 1
With the distribution motor removed, manually
activate the distribution flaps by turning the centre of
the control fully from one side to the other.
Does the flap cover the whole range of
movement, without any areas of resistance?
YES
Remove the footwell vent ducts (lower ducts) to
check that the lower flap control linkages are
present and correctly fitted (they are connected to
the upper flaps).
Also ensure that lower flaps move when the
distribution flap manual control is operated.
Do the footwell (lower) distribution flaps move
when the distribution flaps are controlled?
YES
NORemove the dashboard in order to check
that there is nothing preventing the flaps
from moving (see MR 412, Bodywork,
57A, Interior accessories, Dashboard:
Removal - Refitting). Carry out any
repairs (eliminate any foreign bodies
which may be blocking the flaps and
lubricate the centre of the flap control).
Replace the distribution - ventilation unit if
it is not possible to repair it.
NOIf the mountings of the lower flap control
linkages are not damaged: resecure the
linkages and grease them slightly. If a
repair is not possible or if the mountings
are damaged: replace the distribution -
ventilation unit.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

62B-77
MR-413-X44-62B000$828_eng.mif
V1

Vdiag No.: 44CLIMATE CONTROL
Diagnostic - Fault finding chart62B
ALP 5 No passenger compartment ventilation
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Special notes:
The intermediate connector is located on the distribution-ventilation unit and the
passenger compartment blower unit control module is located slightly higher up,
below the heater matrix pipes.
Use the W iring Diagram Technical Note for the New Twingo.
Using the diagnostic tool, check that the passenger compartment
blower control setting given by the computer varies from 0 to 100 % by
checking parameter PR019 PASSENGER COMPARTMENT BLOWER
PWM SETTING (refer to the interpretation of this parameter).
Does the value vary?
Check that the control voltage (PWM) from the passenger compartment blower power module varies between 0
and 12 V (from 0 to 100 %) by measuring this voltage between connection 38LR of component 1023 and earth
MAN (connector disconnected).
Does the voltage vary correctly?
NOYES
Check the insulation and continuity of connection 38LR between components 419
and 1023.
If the connection is faulty (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for the repair), repair the wiring, otherwise replace the wiring.
Before ignition feed, check for + 12 V accessories feed on connection SP3 of
component 1023 in relation to the chassis earth.
●Check the continuity of connection MAN between the intermediate connector and
component 1023.
●Check the continuity of connection MAN between the intermediate connector and
the chassis earth.
If the connection is faulty (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for the repair), repair the wiring, otherwise replace the wiring.
If there is no +12 V accessories feed, check the condition and position of fuse F28 (30A)
in the passenger compartment fuse box. Consult section 81C Fuses.
If the checks do not reveal any faults, carry out conformity check on component 1016
and component 1428 if the vehicle is fitted with electric windows.
NOContact the
Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
CLIM_V44_ALP5

62B-79
MR-413-X44-62B000$874_eng.mif
V1
62B
CLIMATE CONTROL
Diagnostic - Fault finding chart
Preliminary cold loop efficiency test
ALP 8 No cold air
NOTESOnly deal with this customer complaint after a full check with the diagnostic tool
(fault reading and configuration checks).
Check that the engine speed is greater than 750 rpm and that the exterior
temperature is above 3 ˚C.
Check that the fuses are sound.
Use a multimeter and a 21 W test light.
Use the Wiring Diagram Technical Note, NEW TWINGO.
Engine running, air conditioning in maximum cold
position and maximum ventilation speed. After
10 minutes, is the high pressure pipe at the
compressor outlet hot, and the low pressure pipe at
the evaporator outlet cold and iced up?
NO
Check the cleanliness of the condenser. Touch the
pipes: are they warmer at the inlet than the outlet?
YES
Is the dehydrator reservoir pipe hot at the inlet and
outlet?
YES
Is the expansion valve pipe hot at the inlet and
outlet?
NO
Is the evaporator pipe hot at the inlet and outlet?
NO
1
YES2
NOReplace the condenser (see MR 411
Mechanical, 62A, Air conditioning,
Condenser: Removal - Refitting).
NOReplace the dehydrator reservoir
(see MR 411 Mechanical, 62A, Air
conditioning, Dehydrator reservoir:
Removal - Refitting).
YESReplace the expansion valve (see MR 411
Mechanical, 62A, Air conditioning,
Expansion valve: Removal - Refitting).
YESReplace the evaporator (see MR 411
Mechanical, 62A, Air conditioning,
Evaporator: Removal - Refitting).
AFTER REPAIRCarry out a complete check with the diagnostic tool.

Vdiag No.: 44
MR-413-X44-62B000$874_eng.mif

62B-82
MR-413-X44-62B000$874_eng.mif
V1

Vdiag No.: 44CLIMATE CONTROL
Diagnostic - Fault finding chart62B
ALP 8
CONTINUED 3
Carry out fault finding on the injection system to ensure that no fault is present (if faults are displayed by the injection
computer, engagement of the air conditioning may be inhibited). If there are present or stored faults, carry out the necessary
repairs (see 13B, Diesel injection or 17B, Petrol injection).
Check that the refrigerant fluid pressure is correct (neither too low nor too high) using the PR037 Refrigerant fluid
pressure parameter (see Conformity check, Cold loop sub-function).
Check that the engine cooling fan assembly is at speed 1 by
viewing the following status on the cold loop sub-function
screen:
- Status ET022 Low-speed fan assembly request should
display ACTIVE.
Note:
These statuses are not displayed by all types of injection
(see Conformity check, Cold loop sub-function).
Does the engine cooling fan operate at low speed?
YES
NO
Using the diagnostic tool, run command
AC154 Low speed fan assembly relay.
Does the engine cooling fan operate at
low speed?
NO YES
Connector of component 321 disconnected. Connect a test
light between connection 49L of component 321 and the
chassis earth and run command AC154 Low speed fan
assembly relay.
Does the test light illuminate?
YES NO
Carry out fault finding
on the injection
system (sub-function:
cold loop and engine
cooling for low speed
fan assembly
activation).
Measure the resistance of component 321, between connections
49L and 49B of component 321. If the resistance measured is
infinite, replace the fan assembly resistor (component 321).D
AFTER REPAIRCarry out a complete check with the diagnostic tool.