2009 RENAULT TWINGO RS Engine And Peripherals Workshop Manual

11A-44
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
REFITTING
I - REFITTING PREPARATION OPERATION
aparts always to be replaced: Timing belt
aparts always to be replaced: Timing belt tension-
ing rollerII - REFITTING OPERATION FOR PART
CONCERNED
aRefit a new timing tensioning roller.
aCheck that:
-the lug (20) of the tensioning roller is in place in the
groove (21) of the cylinder head,
-the high pressure pump mark (22) is one tooth to
the right from the vertical axis (23) ,
-the crankshaft is resting on the tool (Mot. 1489)
(the cotter (24) of the crankshaft timing sprocket
upwards).
109042
109043

11A-45
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
aRemove a bolt from the camshaft pulley wheel (25) .
aLoosen the two other camshaft pulley wheel bolts by
one turn.
14489
109042

11A-46
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
aFit the timing belt, starting with the crankshaft
sprocket, aligning the marks on the belt with those
on the crankshaft sprockets, the camshaft and the
high-pressure pump. There should be 19 tooth spac-
es between the sprocket marks and 51 tooth spaces
between the crankshaft sprockets and the high pres-
sure pump.
aBring the tensioning roller adjustable index (26) op-
posite the lug (27) using a 6 mm Allen key, turning
anti-clockwise.
aTighten the tensioning roller bolt.
109044
19658

11A-47
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
aCheck that the camshaft pulley hub bolts are not ful-
ly up against the camshaft pulley wheel.
aRefit the camshaft pulley wheel bolt.
aTighten the camshaft pulley wheel bolts.aRemove:
-the TDC setting pin (Mot. 1489),
109047
109045

11A-48
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
-the camshaft pulley timing pin (Mot. 1430).
aRotate the crankshaft twice clockwise (timing end)
before the camshaft pulley hole (28) is opposite the
cylinder head hole (29) .
aScrew tool (Mot. 1489) into the cylinder block.
aBring the crankshaft slowly and smoothly into con-
tact with the tool (Mot. 1489).
aSet the camshaft pulley using the (Mot. 1430).aIf the (Mot. 1430) does not fit in, loosen the camshaft
pulley wheel bolts by up to one turn.
aTurn the camshaft pulley hub using an offset span-
ner to set the camshaft pulley hub.
aDo not tighten the camshaft pulley wheel bolts.
107270
109049
109048

11A-49
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
aCheck that the crankshaft timing sprocket collet (30)
is positioned vertically at the top.
109045
Note:
After two turns, the tension wheel index markers
may be in two different positions.
The rotation of the tension wheel eccentric
depends on the position.

11A-50
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
1 - First position
aLoosen the tensioning roller bolt by up to one turn,
holding it with a 6 mm Allen key.
aGradually align the adjustable index (31) in the mid-
dle of the timing window (32) , turning the key anti-
clockwise.2 - Second position
aLoosen the tensioning roller bolt by up to one turn,
holding it with a 6 mm Allen key.
aGradually align the adjustable index (33) in the mid-
dle of the timing window (34) , turning the key clock-
wise.
aTorque tighten the tensioning roller bolt (27 N.m).
aTorque tighten the camshaft pulley wheel bolts
(14 N.m).
111083
111081111082
111081

11A-51
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
aRemove:
-the (Mot. 1489),
-the (Mot. 1430).
aRotate the crankshaft twice clockwise (timing end)
before the camshaft pulley hole is opposite the cylin-
der head hole.
aScrew tool (Mot. 1489) into the cylinder block.
aBring the crankshaft slowly and smoothly against the
TDC setting pin.
aSet the camshaft pulley using the (Mot. 1430).
aIf this is not possible, repeat the operation for refit-
ting the timing belt.
aRemove:
-the (Mot. 1489),
-the (Mot. 1430).
III - FINAL OPERATION
aRefit the TDC pin plug, coating the thread with SILI-
CONE ADHESIVE SEALANT (see Vehicle: Parts
and consumables for the repair) (04B, Consum-
ables - Products).
aTorque tighten the TDC setting pin plug (25 N.m).
aRefit the cylinder head suspended mounting .
aTorque tighten the cylinder head suspended
mounting bolts (25 Nm).aRefit the lower timing cover, positioning the tab (35)
in the opening (36) of the inner timing cover.
aRefit:
-the upper timing cover,
-the camshaft position sensor (see 13B, Diesel in-
jection, Camshaft position sensor: Removal -
Refitting, page 13B-14) ,
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) ,
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (42A, Upper
front structure),
-the halogen headlights (see Halogen headlight:
Removal - Refitting) (80B, Headlights),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
109049
19659