2009 RENAULT TWINGO RS wheel

19A-56
COOLING
Engine cooling fan assembly: Removal - Refitting
K4M
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the engine undertray,
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the headlights (see Halogen headlight: Removal
- Refitting) (80B, Headlights),
-the bonnet catch (see Bonnet lock: Removal -
Refitting) (52A, Non-side opening element mecha-
nisms),
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (42A, Upper
front structure).
aRemove the air inlet pipe scoop (1) .II - REMOVAL OPERATION
aDisconnect:
-the engine cooling fan assembly resistor connector
(2) ,
-the engine cooling fan assembly connector (3) .
aUnclip:
-the engine cooling fan assembly wiring at (4) ,
-the cooling radiator top and bottom hose from the
engine cooling fan assembly.
aUnclip the engine cooling fan assembly from the ra-
diator at (5) by pushing it upwards to detach the
brackets holding it.
aRemove the engine cooling fan assembly upwards.
REFITTING
I - REFITTING OPERATION
aFit the engine cooling fan assembly:
aClip the engine cooling fan assembly to the cooling
radiator.
aClip:
-the cooling radiator top and bottom hose on the en-
gine cooling fan assembly,
-the engine cooling fan assembly wiring.
aConnect:
-the engine cooling fan assembly connector,
145934
132336

19A-57
COOLING
Engine cooling fan assembly: Removal - Refitting
K4M
19A
-the engine cooling fan assembly resistor connec-
tor.
II - FINAL OPERATION
aRefit:
-the air inlet pipe scoop,
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (42A, Upper
front structure),
-the bonnet catch (see Bonnet lock: Removal -
Refitting) (52A, Non-side opening element mecha-
nisms),
-the headlights (see Halogen headlight: Removal
- Refitting) (80B, Headlights),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the engine undertray.
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).

19A-58
COOLING
Coolant pump inlet pipe: Removal - Refitting
K9K
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aDisconnect the battery (see ) (MR 411, 80A, Bat-
tery).
aRemove:
-the engine cover,
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (MR 411, 85A, Wip-
ers - Washers),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior
equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (MR 412, 56A, Exterior equipment),
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the headlights (see Halogen headlight: Removal
- Refitting) (MR 411, 80B, Headlights),
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (MR 412,
42A, Upper front structure).
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) .
aRemove the engine tie-bar (see 19D, Engine
mounting, Lower engine tie-bar: Removal - Refit-
ting, page 19D-18) . Special tooling required
Mot. 1672Low er engine support.
Mot. 1448Remote operation pliers for
hose clips .
Tightening torquesm
subfame front bolt62 Nm
subframe rear bolt105 Nm
IMPORTANT
Consult the safety and cleanliness advice and oper-
ation recommendations before carrying out any
repair (see ) .
IMPORTANT
When working in the engine compartment, take
care as the radiator fan(s) may start up unexpect-
edly (risk of being cut).
To avoid any risk of serious burns when the engine
is hot:
-do not open the expansion bottle cap,
-do not drain the cooling system,
-do not open the bleed screw(s).
WARNING
Before the operation, protect the electrical accesso-
ries to prevent any risk of shor t circuiting and pro-
tect the belts to avoid damaging them.
WARNING
When carr ying out a repair that requires a complete
change, it is essential to flush the circuit with clean
water, blast compressed air through the circuit to
drive out the water, fill and bleed the circuit and
then measure the effective protection.
The cr iteria to be met are:
-protection down to -25˚C ±± ± ±
2 for cold and temper-
ate countries,
-protection down to -40˚C ±± ± ±
2 for "extreme cold"
countries.
WARNING
The coolant helps to keep the engine running prop-
erly (heat exchange).
The system must not operate using pure water.

19A-60
COOLING
Coolant pump inlet pipe: Removal - Refitting
K9K
19A
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) .
aRemove the (Mot. 1672).
aRefit:
-the new subframe front bolt,
-the new subframe rear bolt.
aTorque tighten:
-the subfame front bolt (62 Nm),
-the subframe rear bolt (105 Nm).
aRefit the engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) .
aFill the cooling system (see 19A, Cooling, Cooling
system: Draining - Refilling, page 19A-9) .
aRefit:
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (MR 412,
42A, Upper front structure),
-the headlights (see Halogen headlight: Removal
- Refitting) (MR 411, 80B, Headlights),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (MR 412, 56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior
equipment),
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (MR 411, 85A, Wip-
ers - Washers),
-the engine cover.
aConnect the battery (see ) (MR 411, 80A, Battery).

19A-64
COOLING
Expansion bottle: Removal - Refitting
D4F or D7F or K4M or K9K
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).
aRemove the front engine cover.
aRemove the oil filler neck.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the bolts (1) from the expansion bottle.
aMove the expansion bottle aside following the ar-
rows (2) and (3) .
aFit the tool (Ms. 583) on the expansion bottle hoses.
aUsing the (Mot. 1448) or (Mot. 1202-01) or (Mot.
1202-02) remove:
-the clip of the expansion bottle top hose,
-the clip of the expansion bottle bottom hose.
aDisconnect:
-the expansion bottle top hose,
-the expansion bottle bottom hose.
aRemove the expansion bottle.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aConnect:
-the expansion bottle bottom hose,
-the expansion bottle top hose.
aUsing the (Mot. 1448) or (Mot. 1202-01) or (Mot.
1202-02) fit:
-the clip of the expansion bottle bottom hose,
-the clip of the expansion bottle top hose. Special tooling required
Ms. 583Pipe clamps .
Mot. 1448Remote operation pliers for
hose clips .
Mot. 1202-01Clip pliers for hose clips
(large size).
Mot. 1202-02Clip pliers for hose clips
(small size)
K9K
D4F
120514

19A-65
COOLING
Expansion bottle: Removal - Refitting
D4F or D7F or K4M or K9K
19A
aRemove the tool (Ms. 583) from the expansion bottle
hoses.
aRefit the expansion bottle.
II - FINAL OPERATION
aTop up the coolant level in the expansion bottle.
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
aRefit the engine cover.
aRefit the oil filler neck. K9K
D4F

19C-5
TANK
Fuel tank: Removal - Refitting
D4F or D7F or K4M or K9K
19C
aDisconnect:
-the fuel level sensor module connector (2) ,
-the fuel level sensor module pipe union (3) .
aRemove the rear wheels (see Wheel: Removal -
Refitting) (35A, Wheels and tyres).
aRemove the rear brake drums (see Rear brake
drum: Removal - Refitting) (33A, Rear axle com-
ponents).
aUnclip:
-the handbrake cable from the secondary brake
shoe,
-the handbrake cable from the flange.aRemove:
-the clip (4) between the catalytic converter and the
rear silencer,
-the exhaust pipe rubber mounting bush bolt (5) .
119691
WARNING
To prevent impurities from entering the circuit,
place protective plugs on all fuel circuit compo-
nents exposed to the open air.
D4F or D7F or K9K
D4F or D7F or K9K
119689

19C-10
TANK
Fuel tank: Removal - Refitting
D4F or D7F or K4M or K9K
19C
aRefit:
-the heat shield under the tank,
-the heat shield clips under the tank
aTighten to torque:
-the exhaust pipe rubber mounting bush bolt (21
N.m),
-the clip between the catalytic converter and the
rear silencer (21 N.m).
aClip:
-the handbrake cable onto the flange,
-the handbrake cable onto the secondary brake
shoe.
aRefit the rear brake drums (see Rear brake drum:
Removal - Refitting) (33A,Rear axle components).
aRefit the rear wheels (see Wheel: Removal - Refit-
ting) (35A, Wheels and tyres).
aConnect:
-the fuel level sensor module pipe union,
-the fuel level sensor module connector.
aRefit the access flap for the fuel level sensor mod-
ule.
aRefit the rear bench seat.
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery). D4F or D7F or K9K