Page 83 of 241
85A-13
WIPING - WASHING
Windscreen wiper motor: Removal - Refitting
LEFT-HAND DRIVE
85A
aRefit:
-the mechanism drive linkage (4) , ensuring that it is
parallel to the axis connecting the two windscreen
wiper motor lower bolts (5) ,
-the windscreen wiper motor shaft nut.
III - FINAL OPERATION.
aRefit:
-the windscreen wiper mechanism (see 85A, Wi-
ping - Washing, Windscreen wiper mechanism:
Removal - Refitting, page 85A-10) ,
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior equi-
pment).
aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aRefit the front wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) .
104932
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
Page 84 of 241

85A-14
WIPING - WASHING
Windscreen wiper motor: Removal - Refitting
RIGHT-HAND DRIVE
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove:
-the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) ,
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior equi-
pment),
-the front windscreen wiper mechanism (see 85A,
Wiping - Washing, Windscreen wiper mecha-
nism: Removal - Refitting, page 85A-10) .II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the windscreen wiper motor shaft nut (1) .
aExtract the mechanism drive linkage from the winds-
creen wiper motor shaft.
aRemove:
-the bolts (2) from the windscreen wiper motor,
-the windscreen wiper motor (3) .
REFITTING
I - REFITTING PREPARATIONS OPERATION
aConnect:
-the windscreen wiper motor connector,
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) .
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aDisconnect:
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) ,
-the windscreen wiper motor connector. WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
125227
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
Page 85 of 241

85A-15
WIPING - WASHING
Windscreen wiper motor: Removal - Refitting
RIGHT-HAND DRIVE
85A
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the windscreen wiper motor,
-the windscreen wiper motor bolts.
aRefit:
-the mechanism drive linkage (4) , ensuring that it is
parallel to the axis connecting the two windscreen
wiper motor lower bolts (5) ,
-the windscreen wiper motor shaft nut.
III - FINAL OPERATION.
aRefit:
-the windscreen wiper mechanism (see 85A, Wi-
ping - Washing, Windscreen wiper mechanism:
Removal - Refitting, page 85A-10) ,
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior equi-
pment).
aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
aMove the wiper stalk from (0) to (1), then from (1) to
(0).aRefit the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) .
125227
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
Page 87 of 241
85A-17
WIPING - WASHING
Rear screen wiper arm: Removal - Refitting
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aVisually mark the position of the rear screen wiper
arm for the refitting operation.II - REMOVAL OPERATION FOR PART
CONCERNED
aOpen the rear screen wiper arm nut cover (1) .
aRemove:
-the nut (2) from the rear screen wiper arm,
-the rear screen wiper arm using the (Ele. 1552). Special tooling required
Ele. 1552Tool for removing rear screen
wiper arms.
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119520
119522
119523
Page 89 of 241

85A-19
WIPING - WASHING
Rear screen wiper motor: Removal - Refitting
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aRemove:
-the rear screen wiper arm (see 85A, Wiping -
Washing, Rear screen wiper arm: Removal - Re-
fitting, page 85A-17) ,
-the tailgate trim (see Tailgate trim: Removal - Re-
fitting) (MR 412, 73A, Non-side opening elements
trim).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the connector (1) from the rear screen
wiper motor.
aRemove:
-the rivets (2) from the rear screen wiper motor (see
Riveted connection: Description) (MR 400, 40A,
General information),
-the rear screen wiper motor (3) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the rear screen wiper motor ,
-the rear screen wiper motor rivets (see Riveted
connection: Description) (MR 400, 40A, General
information).
aConnect the rear screen wiper motor connector.
II - FINAL OPERATION.
aRefit the tailgate trim (see Tailgate trim: Removal -
Refitting) (MR 412, 73A, Non-side opening ele-
ments trim).
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aRefit the rear screen wiper arm (see 85A, Wiping -
Washing, Rear screen wiper arm: Removal - Re-
fitting, page 85A-17) . WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119425
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
Page 91 of 241
85A-21
WIPING - WASHING
Rain and light sensor: Removal - Refitting
LIGHTS + AUTOMATIC WINDSCREEN WIPER
85A
aUnclip:
-the clips (5) from the rain and light sensor's printed
circuit unit using the (Car. 1363).
aRemove the rain and light sensor's printed circuit
unit.
REFITTING
I - REFITTING PREPARATIONS OPERATION
a
1 - Replacing the rain and light sensor
aClean the windscreen using the (Car. 1363).
102446
124344
WARNING
Remove and refit the rain sensor in totally clean
conditions: any dust or cloth residue could cause
a malfunction.
Do not touch the electronic par t of the sensor. Fit
the sensor to the vehicle immediately after remo-
ving it from its packaging.
124346
Page 115 of 241

87B-1
PASSENGER COMPARTMENT CONNECTION UNIT
UCH: Removal - Refitting
87B
REMOVAL
I - OPERATION FOR REMOVAL OF PART
CONCERNED
aWhen replacing, carry out the necessary operations
using the Diagnostic tool (see Fault finding - Re-
placement of components) (MR 413, 87B, Pas-
senger compartment connection unit).
a
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of compo-
nents)(MR 413, 88C, Airbags and seat belt preten-
sioners).
aSwitch off the ignition.
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .aUnclip the dashboard lower trim (1)
aDisconnect the different connectors (2) from the
dashboard lower trim. Equipment required
Diagnostic tool
RIGHT-HAND DRIVE
IMPORTANT
To avoid any risk of triggering when working on
or near a pyrotechnic component (airbags or pre-
tensioners), lock the airbag computer using the
diagnostic tool.
When this function is activated, all the trigger
lines are inhibited and the airbag warning light on
the instrument panel lights up continuously (igni-
tion on).
IMPORTANT
Never handle the pyrotechnic systems (preten-
sioners or airbags) near to a source of heat or
naked flame - they may be triggered.
LEFT-HAND DRIVE
120278
119711
Page 120 of 241
87C-2
OPENING ELEMENT MANAGEMENT
Opening elements management: List and location of components87C
4 - Central door locking switch
To remove it (see 84A, Control - Signals, Hazard
warning lights and central door control: Removal -
Refitting, page 84A-10) .
5 - Tailgate opening switch
121084
120162