2009 RENAULT TWINGO RS warning

84A-10
CONTROL - SIGNALS
Hazard warning lights and central door control: Removal - Refitting84A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see MR 413 Fault finding, 88C, Airbags and pre-
tensioners, Fault finding - Replacement of com-
ponents).
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove:
-the instrument panel (see 83A, Instrument panel,
Instrument panel: Removal - Refitting, page
83A-1) ,
-the passenger front airbag (1) (see 88C, Air bag
and Pretensioners, Passenger's frontal airbag:
Removal - Refitting, page 88C-8) .
aUnclip the side trim from the driver's side dashboard
(2) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the dashboard central trim (3) .
aDisconnect the hazard warning light and central
door locking switch connector.
aUnclip the hazard warning light and central door loc-
king switch at (4) .
aRemove the hazard warning light and central door
locking switch (5) . Equipment required
Diagnostic tool
119517
119518
119539

84A-11
CONTROL - SIGNALS
Hazard warning lights and central door control: Removal - Refitting84A
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the hazard warning light and central door loc-
king switch.
aConnect the hazard warning light and central door
locking switch connector.
II - FINAL OPERATION.
aClip on:
-the dashboard central trim,
-the side trim from the driver's side dashboard.
aRefit:
-the passenger front airbag (see 88C, Air bag and
Pretensioners, Passenger's frontal airbag: Re-
moval - Refitting, page 88C-8) ,
-the instrument panel (see 83A, Instrument panel,
Instrument panel: Removal - Refitting, page
83A-1) .
aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
aUnlock the airbag computer using the Diagnostic
tool (see MR 413 Fault finding, 88C, Airbags and
pretensioners, Fault finding - Replacement of
components).

85A-6
WIPING - WASHING
Windscreen wiper arm: Removal - Refitting
LEFT-HAND DRIVE
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aVisually mark the position of the wiper arms (1) .II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the nut covers (2) .
aRemove nuts (3) .
aRemove the windscreen wiper arms (4) using the
(Ele. 1294-01) (5) . Special tooling required
Ele. 1294-01Tool for removing wiper arms.
Tightening torquesm
wiper arm nuts21 Nm
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119382
119385
119386
119387

85A-8
WIPING - WASHING
Windscreen wiper arm: Removal - Refitting
RIGHT-HAND DRIVE
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aVisually mark the position of the wiper arms (1) .II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the nut covers (2) .
aRemove nuts (3) .
aRemove the windscreen wiper arms (4) using the
(Ele. 1294-01) (5) . Special tooling required
Ele. 1294-01Tool for removing wiper arms.
Tightening torquesm
wiper arm nuts21 Nm
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119382
125228
125229
125230

85A-9
WIPING - WASHING
Windscreen wiper arm: Removal - Refitting
RIGHT-HAND DRIVE
85A
REFITTING
REFITTING OPERATION FOR PART CONCERNED
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aFit the windscreen wiper arms in the position marked
before the removal operation (1) .
aRefit the wiper arm nuts.
aTorque tighten the wiper arm nuts (21 Nm).
aRefit the wiper arm nut covers.WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119382

85A-10
WIPING - WASHING
Windscreen wiper mechanism: Removal - Refitting
LEFT-HAND DRIVE
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove:
-the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) ,
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior equi-
pment).
II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove:
-the front windscreen wiper mechanism bolts (1) ,
-the windscreen wiper mechanism.
aDisconnect the windscreen wiper motor connector.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aConnect the windscreen wiper motor connector.
aRefit:
-the windscreen wiper mechanism,
-the windscreen wiper mechanism bolts.
II - FINAL OPERATION.
aRefit the scuttle panel grille (see Scuttle panel
grille: Removal - Refitting) (MR 412, 56A, Exterior
equipment).
aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aRefit the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) . WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119389
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.

85A-11
WIPING - WASHING
Windscreen wiper mechanism: Removal - Refitting
RIGHT-HAND DRIVE
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove:
-the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) ,
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior equi-
pment).
II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove:
-the front windscreen wiper mechanism bolts (1) ,
-the windscreen wiper mechanism.aDisconnect the windscreen wiper motor connector
(2) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aConnect the windscreen wiper motor connector.
aRefit:
-the windscreen wiper mechanism,
-the windscreen wiper mechanism bolts.
II - FINAL OPERATION.
aRefit the scuttle panel grille (see Scuttle panel
grille: Removal - Refitting) (MR 412, 56A, Exterior
equipment).
aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aRefit the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) . WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
125232
125231
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.

85A-12
WIPING - WASHING
Windscreen wiper motor: Removal - Refitting
LEFT-HAND DRIVE
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove:
-the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) ,
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior equi-
pment),
-the front windscreen wiper mechanism (see 85A,
Wiping - Washing, Windscreen wiper mecha-
nism: Removal - Refitting, page 85A-10) .
II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the windscreen wiper motor shaft nut (1) .
aExtract the mechanism drive linkage from the winds-
creen wiper motor shaft.aRemove:
-the bolts (2) from the windscreen wiper motor,
-the windscreen wiper motor (3) .
REFITTING
I - REFITTING PREPARATIONS OPERATION
aConnect:
-the windscreen wiper motor connector,
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) .
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aDisconnect:
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) ,
-the windscreen wiper motor connector.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the windscreen wiper motor,
-the windscreen wiper motor bolts. WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119390
119391
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.