2009 RENAULT TWINGO RS change time

86A-9
MR-413-X44-86A000$504_eng.mif
V1
86A
RADIO
Anti-theft code
The radio is protected by a four digit code. This code must be entered via the control satellite or the radio keypad
each time the battery is disconnected.
Entering the code with the control on the steering wheel:
Press the lower button on the control to confirm an entry.
Entering the code using the radio:
Enter the digits using buttons 1, 2, 3 and 4, and then confirm with button 6.
If the code is entered incorrectly, the radio will be locked (1 minute for the first error, 2 minutes for the second error,
4 minutes for the third error, etc. 32 minutes maximum).
Some configurations must be programmed after the code has been entered for the first time (see configuration -
settings). These settings are stored when the battery is disconnected.
Reminder:
The radio will operate for approximately 2 minutes in scrambled mode without the code having been entered (with
regular warning bleeps).
If the vehicle is equipped with a CD changer in the front panel, a code is exchanged between the CD changer and
the radio.
–If a new CD changer is fitted, the radio code is programmed when the battery or CD changer is connected.
–If the radio is replaced, enter the security code of the old radio connected to the CD changer. The CD changer is
programmed with the code for the new radio.
–If the old radio code is lost, the changer code can be cleared using the clearing code. The clearing code is sent by
the Techline.
Note:
If there is a configuration error, you can return to scrambled mode by pressing the 2 and 5 buttons at the same
time as switching the power on. Then wait 2 minutes.
Note:
The CD changer is supplied uncoded. When it is installed in the vehicle, the CD changer is programmed with the
radio supply code.
Reminder:
The radio will operate for approximately 2 minutes in scrambled mode without the code having been entered
(with regular warning bleeps).
MR-413-X44-86A000$504_eng.mif

86A-14
MR-413-X44-86A000$693_eng.mif
V1
86A
RADIO
Self-test procedure
The self-test procedure mode of the previous generation radios (PN0-6) allows certain main functions to be tested:
●by pressing buttons 2 and 4 at the same time, the speakers can be tested. They are supplied one by one; the
display enables the connections and signals from each speaker to be checked,
●by pressing buttons 1 and 6 at the same time, the reception level can be tested (after frequency is displayed),
–9 or letter: good reception,
–
–less than 3: poor reception,
–if 2: total loss of stereo.
The self-test procedure mode of the new generation radios (NR4/5) enables certain main functions to be tested
using the combination of buttons 1, 6 and i. The messages will be displayed in the following way:
●Radio pre-code (one letter/three digits) displayed to avoid the need to remove the radio,
●speaker test with two beeps (bass - treble) from the speakers, with the tested speakers shown on the display
(front left-hand H01, front right-hand H02, rear right-hand H03, rear left-hand H04),
●displays the frequencies and levels of the tuner sensors,
●software version displayed, displays fault finding for the connected aerial if the aerial is supplied by a coaxial
cable; in this case, the display shows H15 with X = 0, 1 or 2 depending on the aerial status (0: open circuit,
1: short circuit to earth, 2: power consumption),
●audio test loudness OFF (H08), cuts any loudness for an audio test.
Note:
The source usage times in 1/6ths of an hour is also displayed (Tuner (H09)/CD (H10)/cassette (H11)/CD changer
(H12)/auxiliary (13)/MP (H14)/Total (H15)).
MR-413-X44-86A000$693_eng.mif

86A-31
MR-413-X44-86A000$819_eng.mif
V1
RADIO
Fault finding chart86A
*SDVC: Speed-dependent volume control.
ALP 7 The volume does not increase with the vehicle speed.
The SDVC* function does not work.
Check the radio configuration (Expert mode).
Set the “SPEED” curve to 5 and run a test when
driving at a speed greater than 48 mph (80 km/h).
Does the volume vary?
YES
The fault has been rectified.
Reset the control to: CURVE 2.
NOCheck the signal on connection 47F
(See Wiring Diagrams Technical Note New
Twingo, code 261) with a multimeter in the
frequency meter position or with an
oscilloscope.
The frequency should change with the speed.
Does the signal frequency change with the
speed?
NO YES
Replace the radio.
The fault is linked to the speed signal
(see 38C, Anti-lock braking system,
conformity check).

86A-32
MR-413-X44-86A000$819_eng.mif
V1
RADIO
Fault finding chart86A
ALP 8 Lighting does not change when the vehicle lights are switched on
Lighting does not change when the vehicle lights
are switched on.
Switch on the lights and check for + 12 V on the
following connections:
–LPD between components 1016 and 261,
–LPD between components 1016 and 653.
Is there + 12 V?NO
YES
Replace the radio.
The fault is not associated with the audio
equipment. Check the continuity and
insulation of the LPD connection with a
multimeter (see Wiring Diagrams Technical
Note for New Twingo, code 261).
YESIs the test OK?
NO
If there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring, otherwise replace it.