2009 RENAULT SCENIC brake

AUTOMATIC TRANSMISSION
Fault finding - Role of components
23A
23A - 19V3 MR-372-J84-23A000$225.mif
AJ0 BVA
Vdiag No.: 04, 05
"SHIFT LOCK" FUNCTION:
Purpose of this function:
Shift-lock: locking the gear lever in position "P" and blocking the transmission to immobilise the vehicle while
stationary.
To release the gear lever from position "P", the vehicle must be stationary and the brake pedal depressed.
"Lever selection"
function
"Shift-lock"
function"Shift-lock" solenoid
Vehicle speed"Instrument panel
display" function
Turbine speed
+ After ignition feed

AUTOMATIC TRANSMISSION
Fault finding - Role of components
23A
23A - 20V3 MR-372-J84-23A000$225.mif
AJ0 BVA
Vdiag No.: 04, 05
"INSTRUMENT PANEL DISPLAY" FUNCTION:
Purpose of this function:
The purpose of this function is to manage the transmission of multiplex line signals required for the instrument panel
display.
"Lever selection"
function
"Instrument
panel display"
functionCAN–Fault warning light
–"Shift-lock" warning
light
"Fault finding" function
"Shift-lock" function "EOBD",function
Brake pedal action

AUTOMATIC TRANSMISSION
Fault finding - Replacement of components
23A
23A-22V3 MR-372-J84-23A000$270.mif
AJ0 BVA
Vdiag No.: 04, 05
Tool fault Diagnostic tool title Defect modes
DF236Invalid engine speed multiplex signal No defect mode.
DF238Signal: raw engine torque multiplex
signal*If the fault occurs while driving, the gearbox
engages fixed 5
th gear.
Restarting is in 3rd gear.
DF256Erratic gear jumping – If caused by brake 2 solenoid valve, system
switches to fixed 3
rd or 5th gear safe mode.
–If caused by clutch 2 solenoid valve, system
switches to fixed 2
nd or 6th gear safe mode.
–If caused by clutch 3 solenoid valve, system
switches to fixed 2
nd, 3rd or 5th gear safe
mode.
–If caused by clutch 1 solenoid valve, system
switches to fixed 3
rd, 5th or 6th gear safe
mode.
In all cases, restarting is in 3
rd gear.
DF273Clutch 1 solenoid valve circuit If the fault occurs while driving, the
transmission engages fixed 5
th gear.
Restarting in fixed 5th gear (no more gear
changes).
DF274Clutch 2 solenoid valve circuit – in the event of open circuit or short circuit+:
No defect mode.
–in the event of short circuit-:
If the fault occurs while driving, the
transmission engages fixed 5
th gear.
Restarting in fixed 3rd gear (no more gear
changes)
DF275Clutch 3 solenoid valve circuit – in the event of open circuit or short circuit+:
No defect mode.
–in the event of short circuit-:
If the fault occurs while driving, the
transmission engages fixed 5
th gear.
Restarting in fixed 5th gear (no gear change)
DF289Automatic transmission multiplex
signalNo defect mode.
DF290Multiplexed ABS signal No defect mode.
DF298Gear shifts – If caused by brake 2 solenoid valve, system
switches to fixed 6
th gear safe mode.
–If caused by clutch 2 solenoid valve, system
switches to fixed 5
th gear safe mode.
Restarting in 3rd gear.
–If caused by clutch 3 solenoid valve, system
switches to fixed 5
th gear safe mode.

AUTOMATIC TRANSMISSION
Fault finding - Replacement of components
23A
23A-23V3 MR-372-J84-23A000$270.mif
AJ0 BVA
Vdiag No.: 04, 05
Tool fault Diagnostic tool title Defect modes
DF300Brake 2 solenoid valve circuit – in the event of open circuit or short circuit+:
No defect mode.
–in the event of short circuit-:
If the fault occurs while driving, the
transmission engages fixed 5
th gear.
Restarting in fixed 3rd gear (no gear change)
DF301Clutch 1 pressure switch circuit No defect mode.
DF302Clutch 2 pressure switch circuit No defect mode.
DF303Clutch 3 pressure switch circuit No defect mode.
DF304Brake 1 pressure switch circuit No defect mode.
DF305Brake 2 pressure switch circuit No defect mode.
DF306Lock-up/brake 1 solenoid valve circuit Fixed 5
th gear engaged.
Restarting in fixed 3rd gear (no gear change).
DF307Engine braking No defect mode.
DF308Computer earth Fixed 5
th gear engaged.

AUTOMATIC TRANSMISSION
Fault finding - Replacement of components
23A
23A-24V3 MR-372-J84-23A000$270.mif
AJ0 BVA
Vdiag No.: 04, 05
Replacing the transmission computer:
Remove the automatic transmission computer (see MR 370 mechanical, 23A, Automatic transmission,
Automatic transmission computer, Removal - Refitting).
Refit the automatic transmission computer (see MR 370 mechanical, 23A, Automatic transmission,
Automatic transmission computer, Removal - Refitting).
Establish dialogue with the diagnostic tool.
Use command VP001 Enter VIN.
Run command VP009 Write last After-Sales Service operation date.
Do not carry out any automatic programming if replacing the automatic transmission computer. Automatic
programming is finalised when the vehicle is driven.
In order to optimise the automatic programming before delivering the vehicle to the customer, apply the
"Programming procedure" shown below.
Replacing the hydraulic distributor:
Remove the transmission hydraulic distributor (see MR 370 mechanical, 23A, Automatic transmission,
Hydraulic distributor, Removal - Refitting).
Refit the transmission hydraulic distributor (see MR 370 Mechanical, 23A, Automatic transmission, Hydraulic
distributor, Removal - Refitting).
Replacing the automatic transmission
Remove the transmission (see MR 370,Mechanical, 23A, Automatic transmission, Removal - Refitting).
Refit the transmission (see MR 370, Mechanical, 23A, Automatic transmission, Removal - Refitting).
Establish communication with the diagnostic tool.
Initialise all the programming, use the command RZ009 Self-adapting clearing (Vdiag05 only).
Run command VP009 Write last After-Sales Service operation date.
The self-programming functions are performed when the vehicle is being driven.
In order to optimise the automatic programming before delivering the vehicle to the customer, apply the
"Programming procedure" shown below.
* APV: After-SalesPROGRAMMING PROCEDURE:
Programming conditions:
The automatic gearbox oil temperature should be between 60˚C and 100˚C.
Stationary, engine running, brake pedal depressed:
Engage neutral at least 5 times to consolidate the programming.
While driving:
Engage the same gear at least 5 times (i.e. in the same conditions) to consolidate the programming.
Note:
Gear changes are slow and harsh the first few times the vehicle is driven, until the automatic transmission computer
has carried out its automatic programming.
During upshifts and downshifts, the system analyses variations in oil pressure, components (play in the brakes and
clutches, changes to spring stiffness due to ageing) and input torque, then corrects them in order to maintain the
quality of gear changes.
The system analyses the turbine speed during the 3 phases of drag reduction (selection of Neutral when stationary,
regulation during drag reduction and deselection of Neutral) and corrects this speed by adjusting the converter
lock-up solenoid valve pressure.

AUTOMATIC TRANSMISSION
Fault finding - Fault summary table
23A
23A - 26V3 MR-372-J84-23A000$360.mif
AJ0 BVA
Vdiag No.: 04, 05AUTOMATIC TRANSMISSION
Fault finding - Fault summary table
*signal: signal
*EVS1 = sequence solenoid valve 1
*EVS2 = sequence solenoid valve 2
*LS = line pressure regulation solenoid valveTool fault Associated DTC Diagnostic tool title
DF023710 Transmission oil temperature sensor circuit
DF038715 Turbine speed sensor circuit
DF067705 Lever position switch circuit
DF084C073 Multiplex network
DF0851753 EVS1* shift solenoid circuit
DF0861758 "ESV2"* shift solenoid circuit
DF091748 "LS"* pressure regulation solenoid valve circuit
DF093826 Manual sequential controls circuit
DF095928 Gear lever lock electromagnet circuit
DF097740 Converter lock-up
DF1085300 Effective average torque multiplex signal
DF171720 Vehicle speed sensor circuit
DF1785600 Accelerator pedal position
DF183C140 No UCH multiplex signal
DF186C100 No injection multiplex signal
DF230C415 Invalid vehicle speed multiplex signal
DF236725 Invalid engine speed multiplex signal
DF2384073 Invalid raw engine torque multiplex signal*
DF256730 Erratic gear jumping
DF273753 Clutch 1 solenoid valve circuit
DF274763 Clutch 2 solenoid valve circuit
DF275768 Clutch 3 solenoid valve circuit
DF2891840 Automatic transmission multiplex signal
DF290C121 Multiplexed ABS signal
DF298893 Gear shifts
DF300758 Brake 2 solenoid valve circuit
DF301751 Clutch 1 pressure switch circuit
MR-372-J84-23A000$360.mif

AUTOMATIC TRANSMISSION
Fault finding - Fault summary table
23A
23A - 27V3 MR-372-J84-23A000$360.mif
AJ0 BVA
Vdiag No.: 04, 05
Tool fault Associated DTC Diagnostic tool title
DF302761 Clutch 2 pressure switch circuit
DF303766 Clutch 3 pressure switch circuit
DF304741 Brake 1 pressure switch circuit
DF305756 Brake 2 pressure switch circuit
DF306743 Lock-up/brake 1 solenoid valve circuit
DF307780 Engine braking
DF3081560 Computer earth

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 50V3 MR-372-J84-23A000$405.mif
AJ0 BVA
Vdiag No.: 04, 05
DF095
PRESENT
OR
STOREDSELECTOR LEVER LOCK ELECTROMAGNET CIRCUIT
1.DEF: Open circuit or short circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
Lever in position "P" (without pressing the brake pedal), "R", "N", "D" or "M".
Customer complaint:
–in the event of open circuit or short circuit+:
The shift-lock solenoid valve cannot be activated: therefore the lever is placed in
position "P", blocking it. Unlocking is a manual operation.
–in the event of a CCM:
The shift-lock solenoid valve is always activated: therefore, no locking of lever.
Use the Wiring Diagrams Technical Note, SCENIC II ph2.
Look for any damage to the harness and check the condition and connection of the connectors on the automatic
transmission computer and on the shift pattern control.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + after ignition feed on connection AP* of component 129.
Check for earth on connection N+ of component 129.
Check the insulation to earth and continuity of the following connection:
●Connection code 5DU, between components 119 and 129.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
In the event of a fault, replace the shift pattern control.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.
AJ0_V04_DF095/AJ0_V05_DF095