2009 RENAULT SCENIC diagram

2Transmission
V3 MR-372-J84-23A000$TOC.mif
V3
23A
"The repair procedures given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The procedures may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories from
which his vehicles are constructed."
V3
All rights reserved by Renault s.a.s.
Edition Anglaise
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault s.a.s.
© Renault s.a.s. 2009
AUTOMATIC TRANSMISSION
AJ0 BVA
Vdiag No.: 04, 05
Fault finding - Introduction 23A - 2
Fault finding - List and location of components 23A - 7
Fault finding - Role of components 23A - 9
Fault finding - Operating diagram 23A - 10
Fault finding - Role of components 23A - 12
Fault finding - Replacement of components 23A - 21
Diagnostics - Configuration and programming 23A - 25
Fault finding - Fault summary table 23A - 26
Fault finding - Interpretation of faults 23A - 28
Fault finding - Conformity check 23A - 114
Fault finding - Status summary table 23A - 115
Fault finding - Interpretation of statuses 23A - 116
Fault finding - Parameter summary table 23A - 134
Fault finding - Interpretation of parameters 23A - 135
Fault finding - Command summary table 23A - 145
Fault finding - Interpretation of commands 23A - 146
Fault finding - Customer complaints 23A - 155
Fault finding - Fault Finding Chart 23A - 156

AUTOMATIC TRANSMISSION
Fault finding - Introduction
23A
23A-2V3 MR-372-J84-23A000$045.mif
123A
AJ0 BVA
Vdiag No.: 04, 05AUTOMATIC TRANSMISSION
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type:
Fault finding procedures (this document):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM)
Type of diagnostic tools:
–CLIP
Special tooling required:
3. REMINDERS
Procedure
To perform fault finding on the vehicle's computers, switch on the ignition in fault finding mode.
Proceed as follows:
–vehicle's card in reader;
–press and hold the Start button (longer than 5 seconds) with start-up conditions not fulfilled,
–connect the diagnostic tool and perform the required operations.
To cut off the + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–press the Start button twice briefly (less than 3 seconds),
–ensure that the + after ignition feed has been cut off by checking that the computer indicator lights on the
instrument panel have gone out. Vehicle(s): SCENIC II ph2
Function concerned: Automatic transmissionName of computer: Automatic transmission
Vdiag No.: 04, 05
Special tooling required
Multimeter
Elé. 1681Universal bornier
AJ0_V04_PRELI/AJ0_V05_PRELI
MR-372-J84-23A000$045.mif

AUTOMATIC TRANSMISSION
Fault finding - Operating diagram
23A
23A - 10V3 MR-372-J84-23A000$180.mif
AJ0 BVA
Vdiag No.: 04, 05AUTOMATIC TRANSMISSION
Fault finding - Operating diagram
Line pressure
OIL PUMP
Hydraulic
distributor
Primary regulation valve (pressure regulating valve)
LS pressure regulation solenoid valve
Manual valve
Clutch
modulating
solenoid valve 1
Clutch
modulating
solenoid valve 2Clutch
modulating
solenoid valve 3Brake
modulating
solenoid valve 2Modulating solenoid
valve
lock-up/brake 1
Sequence
solenoid valve 1Sequence solenoid
valve 2
Clutch 1 Clutch 2 Clutch 3 Brake 2Brake
1Torque
converter
lock-up
Hydraulic receivers
MR-372-J84-23A000$180.mif

AUTOMATIC TRANSMISSION
Fault finding - Operating diagram
23A
23A - 11V3 MR-372-J84-23A000$180.mif
AJ0 BVA
Vdiag No.: 04, 05
Hydraulic distributor
Clutch modulating
solenoid
valve 1Clutch modulating
solenoid
valve 2Clutch modulating
solenoid
valve 3Brake modulating
solenoid
valve 2Modulating solenoid
valve, lock-up/brake 1
Sequence
solenoid valve 1Sequence solenoid valve 2
Clutch 1
pressure switchClutch 2
pressure switchClutch 3
pressure switchBrake pressure
switch 2Brake pressure
switch 1
Clutch 1 Clutch 2 Clutch 3 Brake 2 Brake 1Torque
converter
lock-up
Hydraulic receivers
Line pressure

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 28V3 MR-372-J84-23A000$405.mif
AJ0 BVA
Vdiag No.: 04, 05AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
DF023
PRESENT
OR
STOREDGEARBOX OIL TEMPERATURE SENSOR CIRCUIT
1.DEF: Open circuit or short circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–in the event of open circuit or short circuit+:
–+ after ignition feed,
–oil temperature ≤ - 40 ˚C,
–vehicle speed > 6 mph (10 km/h).
–in the event of short circuit-:
–+ after ignition feed,
–oil temperature > 180 ˚C,
–vehicle speed > 6 mph (10 km/h).
–accelerator pedal > 12.5 % and engine speed > 305 rpm.
(detection time in the event of short circuit- is 10 minutes).
Effect on system:
–in the event of open circuit or short circuit+:
Gear change quality is reduced.
lock-up is inhibited.
–in the event of short circuit-:
The transmission operates as if the temperature had increased.
Customer complaint:
–in the event of open circuit or short circuit+:
If the fault occurs while driving, the transmission engages fixed 5th gear.
Restarting is in 3rd gear.
Gear change quality is reduced.
Fault warning light on
–in the event of short circuit-:
Fault warning light on
Use the Wiring Diagrams Technical Note, SCENIC II ph2.
Check that the coolant temperature (see 13B, Diesel injection, EDC16, CP33 M9R 721 Conformity check)
is ≥ - 40 ˚C (the transmission oil temperature sensor is within its operating range).
If the oil temperature ≤ - 40 ˚C, move on to step 1.
If the oil temperature is ≥ - 40 ˚C, deal with the fault; move on to step 2.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.
AJ0_V04_DF023/AJ0_V05_DF023
MR-372-J84-23A000$405.mif

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 31V3 MR-372-J84-23A000$405.mif
AJ0 BVA
Vdiag No.: 04, 05
DF038
PRESENT
OR
STOREDTURBINE SPEED SENSOR CIRCUIT
1.DEF: Open circuit or short circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–+ after ignition feed,
–with the engine running,
–vehicle speed > 24 mph (40 km/h),
–engine speed > 1500 rpm,
–turbine speed < 600 rpm and accelerator pedal > 0 %.
Effect on system:
Impossible to calculate gear.
Customer complaint:
Gear on which fault occurred is fixed. Restarting in fixed 3rd gear (no more gear
changes). Manual mode is inhibited. Fault warning light comes on.
Use the Wiring Diagrams Technical Note, SCENIC II ph2.
Look for any damage to the wiring harness, and check the condition and connection of the transmission
computer and the turbine speed sensor.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + after ignition feed on connection AP4 of component 1060.
Is the + after ignition feed still present?
If YES, move on to step 1.
If NO, move on to step 2.
Step 1:
Check the continuity and insulation of the following connections:
●Connection code 5HN.
●Connection code 5DA.
Between components 119 and 1060.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the intermediate connector R22, if the fault is still present, replace component 1060.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.
AJ0_V04_DF038/AJ0_V05_DF038

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 33V3 MR-372-J84-23A000$405.mif
AJ0 BVA
Vdiag No.: 04, 05
If the fault is stored:DF067
PRESENT
OR
STORED
LEVER POSITION SWITCH CIRCUIT
1.DEF: Open circuit or short circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–in the event of open circuit or short circuit-:
–+ after ignition feed and change of lever position.
–in the event of short circuit+:
–+ after ignition feed, initial lever position: Position "P", "R", "N" or "D".
Effect on system:
The lever value is held at its previous valid position until the fault is confirmed. Then
the lever position becomes DRIVE (internal software variable) irrespective of the fault.
–If the fault is present and the lever in position "P", the transmission is in "N", hydraulic
neutral.
–If the fault is present and the lever in position "R", the transmission is in "R", hydraulic
reverse.
–If the fault is present and the lever in position "N", the transmission is in "N", hydraulic
neutral.
–If the fault is present and the lever in position "D", the transmission is in "D", hydraulic
forward gear.
lock-up is inhibited.
Customer complaint:
No lever position display on the instrument panel following fault confirmation and
starting impossible.
If the engine is already running when the fault occurs, there is jolting when shifting from
"P" or "N" to "R" or "D".
Fault warning light comes on.
Use the Wiring Diagrams Technical Note, SCENIC II ph2.
Note:
It is possible to produce this fault if the driver or operator voluntarily keep the lever between two normal positions
for longer than 2 seconds.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.
AJ0_V04_DF067/AJ0_V05_DF067

AUTOMATIC TRANSMISSION
Fault finding - Interpretation of faults
23A
23A - 36V3 MR-372-J84-23A000$405.mif
AJ0 BVA
Vdiag No.: 04, 05
DF084
PRESENT
OR
STOREDMULTIPLEX NETWORK
1.DEF: No multiplex frameworks or invalid values (signal producing computer
problem or CAN connection fault).
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after + APC.
Effect on system:
Engine does not start.
No lever position display on the instrument panel.
Note: the effects of the fault disappear immediately after the multiplex line bus is
re-established.
Customer complaint:
Engine does not start.
No lever position display on the instrument panel.
Jolting during gear changes.
Note: the effects of the fault disappear immediately after the multiplex line bus is
re-established.
Use the Wiring Diagrams Technical Note, SCENIC II ph2.
Run a multiplex network test (see 88B, Multiplex).
Check the continuity and insulation against earth of the following connections:
●Connection code 3MS.
●Connection code 3MT.
Between components 119 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition, wait 1 minute and carry out a road test followed by another
check with the diagnostic tool.
AJ0_V04_DF084/AJ0_V05_DF084