2009 Peugeot 607 Dag bulb
[x] Cancel search: bulbPage 23 of 182
1
26
Anti-lock braking system
(ABS) warning light
This is linked to the warn-
ing light on the instrument
panel.
Display of this warning light is ac-
companied by an audible signal and a
message on the multifunction display.
If the warning light remains on, or
c o m e s o n a t o v e r 8 m p h ( 1 2 k m / h ) , t h i s
indicates a malfunction of the ABS.
H o w e v e r , t h e v e h i c l e r e t a i n s c o n v e n -
t i o n a l s e r v o - a s s i s t e d b r a k i n g .
Consult a PEUGEOT dealer.
Automatic headlamp
adjustment warning light
Display of this warning light
is accompanied by an audi-
ble signal and a message on
the multifunction display.
It comes on if there is a malfunction of
t h e s y s t e m o n v e h i c l e s fi t t e d w i t h x e -
non bulbs.
Consult a PEUGEOT dealer. Electronically controlled
suspension warning light
Display of this warning light
is accompanied by an audi-
ble signal and a message on
the multifunction display.
It comes on when there is a malfunc-
tion of the electronically controlled
suspension.
Select the automatic mode and contact
a PEUGEOT dealer.
P a r t i c u l a t e e m i s s i o n fi l t e r
saturation warning light
(Diesel)
Display of this warning light
is accompanied by an audi-
ble signal and a message on
the multifunction display.
When it comes on with the engine
running, this indicates the start of
saturation of the particulate emission
fi l t e r ( e x c e p t i o n a l l y l o n g p e r i o d s o f
t o w n t y p e d r i v i n g c o n d i t i o n s : r e d u c e d
speed, long tailbacks...).
T o r e g e n e r a t e t h e fi l t e r , y o u a r e a d -
v i s e d t o d r i v e a s s o o n a s p o s s i b l e
a n d w h e n t r a f fi c c o n d i t i o n s p e r m i t a t
a speed of 35 mph (60 km/h) or more
f o r a t l e a s t fi v e m i n u t e s ( u n t i l t h e w a r n -
ing light goes out).
If the light remains on, contact a
PEUGEOT dealer.
W h e n i t c o m e s o n w h e n t h e v e h i c l e i s
m o v i n g , i t i n d i c a t e s a l a c k o f d i e s e l a d -
d i t i v e i n t h e r e s e r v o i r f o r b u r n i n g o f t h e
particles.
Consult a PEUGEOT dealer.
Note: after prolonged operation of
t h e v e h i c l e a t a v e r y l o w s p e e d o r a t
idle, you may sometimes notice steam
coming from the exhaust during ac-
celeration. This has no effect on the
p e r f o r m a n c e o f t h e v e h i c l e o r o n t h e
e n v i r o n m e n t .
Page 80 of 182
5
70
AUTOMATIC HEADLAMP
ADJUSTMENT
In cases of malfunction , the
warning light comes on on
the instrument panel display,
accompanied by an audible
signal and a message on the
multifunction display. The system places
your headlamps to the low position.
Do not touch the xenon bulbs. Consult
a PEUGEOT dealer.
When stationary with the ignition
on , the system automatically corrects
the height of the beam, whatever the
load of the vehicle. The driver is then
assured of having optimum lighting
and not causing a nuisance to other
road users.
WINDSCREEN WIPER STALK
Windscreen wipers
2 Fast wipe (heavy rain).
1 Normal wipe (moderate rain).
I Intermittent wipe
0 Off
Automatic wipe then single sweep.
In the Intermittent position, the wiping
speed is in proportion to the speed of
the vehicle.
In the AUTO position, no further action
on your part is required.
The automatic wiping must
be reactivated if the ignition
has been switched off for more
than one minute, by pressing
the stalk down .
Maintenance position
This position enables the wiper blades
to be removed.
In the minute following switching off of
the ignition, any action on the wipers
stalk positions the wipers at the top
of the windscreen (parking in winter,
cleaning, replacement of the blades).
To reposition the wipers after this has
been done, switch on the ignition and
operate the stalk.
Windscreen and headlamp wash
Pull the windscreen wiper stalk to-
wards you. The windscreen wash then
the windscreen wipers operate for a
fi x e d p e r i o d .
The headlamp wash is also activated,
if the headlamps are on.
Screenwash/headlampwash low When the minimum level of
the reservoir is reached, this
warning light comes on, ac-
companied by an audible
signal and a message on the
multi-function display.
N e x t t i m e y o u s t o p , fi l l t h e s c r e e n -
wash/headlamp wash reservoir.
If the reservoir is empty, the warning
light comes on when the ignition is
switched on, or every time the stalk is
o p e r a t e d , u n t i l t h e r e s e r v o i r i s fi l l e d .
Page 81 of 182
5
70
AUTOMATIC HEADLAMP
ADJUSTMENT
In cases of malfunction , the
warning light comes on on
the instrument panel display,
accompanied by an audible
signal and a message on the
multifunction display. The system places
your headlamps to the low position.
Do not touch the xenon bulbs. Consult
a PEUGEOT dealer.
When stationary with the ignition
on , the system automatically corrects
the height of the beam, whatever the
load of the vehicle. The driver is then
assured of having optimum lighting
and not causing a nuisance to other
road users.
WINDSCREEN WIPER STALK
Windscreen wipers
2 Fast wipe (heavy rain).
1 Normal wipe (moderate rain).
I Intermittent wipe
0 Off
Automatic wipe then single sweep.
In the Intermittent position, the wiping
speed is in proportion to the speed of
the vehicle.
In the AUTO position, no further action
on your part is required.
The automatic wiping must
be reactivated if the ignition
has been switched off for more
than one minute, by pressing
the stalk down .
Maintenance position
This position enables the wiper blades
to be removed.
In the minute following switching off of
the ignition, any action on the wipers
stalk positions the wipers at the top
of the windscreen (parking in winter,
cleaning, replacement of the blades).
To reposition the wipers after this has
been done, switch on the ignition and
operate the stalk.
Windscreen and headlamp wash
Pull the windscreen wiper stalk to-
wards you. The windscreen wash then
the windscreen wipers operate for a
fi x e d p e r i o d .
The headlamp wash is also activated,
if the headlamps are on.
Screenwash/headlampwash low When the minimum level of
the reservoir is reached, this
warning light comes on, ac-
companied by an audible
signal and a message on the
multi-function display.
N e x t t i m e y o u s t o p , fi l l t h e s c r e e n -
wash/headlamp wash reservoir.
If the reservoir is empty, the warning
light comes on when the ignition is
switched on, or every time the stalk is
o p e r a t e d , u n t i l t h e r e s e r v o i r i s fi l l e d .
Page 119 of 182
1010
103
CHANGING A BULB
2 - Main beam headlamps: H1-55 W.
Turn the protective cover of the
faulty bulb a quarter of a turn and
remove it.
Disconnect the connector.
Press the end of the securing clip
to free it. Change the bulb.
W h e n fi t t i n g t h e n e w b u l b , e n s u r e
that the direction notches are po-
sitioned correctly and the securing
c l i p i s fi x e d p r o p e r l y .
Reconnect the connector.
R e fi t t h e p r o t e c t i v e c o v e r . 3 - S i d e l i g h t s : W 5 W .
Pull the socket rearwards.
Remove the bulb and change it.
Front foglamps: H1-55 W.
Handle the bulbs with a dry
cloth.
T h e h e a d l a m p s a r e fi t t e d w i t h
polycarbonate glass with a
protective coating. Do not clean them
with a dry or abrasive cloth, nor with a
detergent or solvent product.
Use a soft, damp cloth with soapy water.
In the engine compartment, remove
the style cover secured by one or two
b u t t e r fl y s c r e w s , a p l a s t i c r e t a i n e r c l i p
and two quarter turn screws.
On the left-hand side, remove the par-
tition by lifting it to gain access to the
lights.
W h e n y o u h a v e fi n i s h e d , d o n o t f o r g e t
to put everything back correctly.
W A R N I N G : R I S K O F E L E C -
TROCUTION
Xenon bulbs must be replaced
by a PEUGEOT dealer.
Front lights 1 - D i p p e d b e a m h e a d l a m p s : X e n o n b u l b . 4 - D i r e c t i o n i n d i c a t o r s :
PY 21 W (amber).
Turn the bulb holder a quarter turn
and remove it.
Remove the bulb and change it.
R e fi t t h e s t y l e c o v e r .
H i g h p r e s s u r e w a s h i n g
When using this type of washing on
stubborn dirt, do not persist on the
headlamps, the lights and their sur-
rounds to avoid damaging their var-
nish and their seal.
In certain climatic conditions
(low temperature, humidity),
condensation on the inside
surface of the glass of the
headlamps and rear lights is normal;
it disappears a few minutes after the
lights are switched on.
Page 120 of 182
1010
104
Integrated direction indicator
repeaters Amber coloured bulbs, such
as the direction indicators and
side repeaters, must be re-
placed with bulbs of identical
s p e c i fi c a t i o n a n d c o l o u r . Rear lights
R e m o v e t h e t w o b u t t e r fl y n u t s s e -
curing the light.
Remove the eyelet.
Take out the lamp.
Unclip the bulb holder.
Change the faulty bulb.
Clip the bulb holder.
W h e n r e fi t t i n g i t , e n s u r e t h a t t h e l a m p
is correctly positioned and secured.
1. D i r e c t i o n i n d i c a t o r s : H p 1 6 .
2. Brake lights/side lights: Hp16.
Detach the luggage net.
Lift the boot carpet with the lifting
hook. Secure this hook behind the
boot seal.
Unclip the lower part of the sill trim,
then dislodge it by pulling upwards.
Remove the plastic retainer clip
s e c u r i n g t h e s i d e t r i m t o t h e fl o o r .
Unclip the side trim.
Push the repeater forwards and re-
lease it.
Remove the repeater and change it.
This can be obtained from a PEUGEOT
dealer. Rear wing lights
Page 121 of 182
1010
104
Integrated direction indicator
repeaters Amber coloured bulbs, such
as the direction indicators and
side repeaters, must be re-
placed with bulbs of identical
s p e c i fi c a t i o n a n d c o l o u r . Rear lights
R e m o v e t h e t w o b u t t e r fl y n u t s s e -
curing the light.
Remove the eyelet.
Take out the lamp.
Unclip the bulb holder.
Change the faulty bulb.
Clip the bulb holder.
W h e n r e fi t t i n g i t , e n s u r e t h a t t h e l a m p
is correctly positioned and secured.
1. D i r e c t i o n i n d i c a t o r s : H p 1 6 .
2. Brake lights/side lights: Hp16.
Detach the luggage net.
Lift the boot carpet with the lifting
hook. Secure this hook behind the
boot seal.
Unclip the lower part of the sill trim,
then dislodge it by pulling upwards.
Remove the plastic retainer clip
s e c u r i n g t h e s i d e t r i m t o t h e fl o o r .
Unclip the side trim.
Push the repeater forwards and re-
lease it.
Remove the repeater and change it.
This can be obtained from a PEUGEOT
dealer. Rear wing lights
Page 122 of 182
1010
105
Remove the three plastic retainer
clips securing the cover trim (those
nearest to the lamp).
Move aside the trim.
Disconnect the lamp harness.
Extract the lamp from its housing.
R e m o v e t h e fl a t s e a l .
Unclip the bulb holder.
Change the faulty bulb.
Clip the bulb holder.
P u t t h e fl a t s e a l b a c k i n p l a c e .
W h e n r e fi t t i n g i t , e n s u r e t h a t t h e l a m p
is correctly positioned and secured.
N u m b e r p l a t e l i g h t s : W 5 W.
Remove the transparent cover using
a screwdriver blade.
Change the faulty bulb.
Boot lid lights
1. Reversing lights: Hp16.
2. S i d e l i g h t s : H p 1 6 .
3. Fog lamps: Hp16.
I f y o u e n c o u n t e r a n y d i f fi c u l t i e s ,
contact a PEUGEOT dealer.
Page 132 of 182
1010
113
TOWING A TRAILER,
CARAVAN, BOAT, ETC...
We recommend the use of original
PEUGEOT towbars and their harnesses
which have been tested and approved
from the design stage of your vehicle and
t h a t y o u e n t r u s t t h e fi t t i n g o f t h e t o w b a r t o
a PEUGEOT dealer.
I f t h e t o w b a r i s n o t fi t t e d b y a P E U G E O T
d e a l e r , i t i s i m p e r a t i v e t h a t i t i s fi t t e d u s -
ing the electrical pre-equipment installed
at the rear of the vehicle, in accordance
with the manufacturer's instructions.
Note: in certain cases of par-
ticularly arduous use (towing
the maximum load in high
temperatures on a steep
slope), the engine automatically lim-
its its power and selects the appropri-
ate automatic gearbox gear in manual
mode. In this case, cutting off the air
conditioning allows the engine power
to be recovered, and therefore the
towing capacity to be increased. A u t o m a t i c a d j u s t m e n t
To avoid causing a nuisance to other
road users, this system automatical-
ly corrects the height of the beam of
xenon bulbs in relation to the vehicle
load after approximately 2 minutes.
The driver is then assured of having
optimum lighting.
D r i v i n g a d v i c e
D i s t r i b u t i o n o f l o a d s : distribute the
load in the trailer so that the heavi-
est loads are as close as possible to
the axle and the nose weight is close
to the maximum authorised without,
however, exceeding it.
Lighting
Tyres: check the tyre pressures of the
towing vehicle (label on the central
door pillar on the driver's side) and of
the trailer towed, observing the recom-
mended pressure.
If the coolant temperature
warning light comes on, stop
the vehicle and switch off the
engine as soon as possible.
I n t h e c a s e o f v e h i c l e s fi t t e d w i t h a n
HDI engine, it is advisable, following
intensive use (towing on a motorway,
prolonged driving, ...), to leave the en-
gine running at idle for approximately
20 seconds before switching off the
ignition. This limits any increase in the
temperature of the engine after it has
been switched off.
In all cases, pay attention to the coolant
temperature.
Brakes: towing increases the braking
distance. Drive at a moderate speed,
change down early and brake gradually.
S i d e w i n d : sensitivity to side wind is
increased. Drive smoothly and at a
moderate speed.
Cooling: towing a trailer on a slope in-
creases the coolant temperature.
As the fan is electrically controlled, its
cooling capacity is not dependent on
the engine speed.