2009 MERCEDES-BENZ G-Class ignition

As an added safety feature, your vehicle has
been equipped with a tire pressure monitoring
system (TPMS) that illuminates a low tire
pressure telltale when one or more of your
tires are significantly underinflated.
Accordingly, when the low tire pressure
telltale illuminates, you should stop and check
your tires as soon as possible, and inflate
them to the proper pressure. Driving on a
significantly underinflated tire causes the tire
to overheat and can lead to tire failure.
Underinflation also reduces fuel efficiency
and tire tread life, and may affect the vehicle’s
handling and stopping ability. Please note that
the TPMS is not a substitute for proper tire
maintenance, and it is the driver’s
responsibility to maintain correct tire
pressure, even if underinflation has not
reached the level to trigger illumination of the
TPMS low tire pressure telltale.
USA only:
Your vehicle has also been equipped with a
TPMS malfunction indicator to indicate when
the system is not operating properly. The
TPMS malfunction indicator is combined with
the low tire pressure telltale. When the
system detects a malfunction, the telltale will
flash for approximately 1 minute and then
remain continuously illuminated. This
sequence will continue upon subsequent
vehicle start-ups as long as the malfunction
exists. When the malfunction indicator is
illuminated, the system may not be able to
detect or signal low tire pressure as intended.
TPMS malfunctions may occur for a variety of
reasons, including the installation of
replacement or alternate tires or wheels on
the vehicle that prevent the TPMS from
functioning properly. Always check the TPMS
malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function
properly.
iUSA only:
If a condition causing the TPMS to
malfunction develops, it may take up to
10 minutes for the system to signal a
malfunction using the TPMS telltale
flashing and illumination sequence.
The telltale extinguishes after a few
minutes driving if the malfunction has been
corrected.
Tire pressure inquiries are made using the
multifunction display. The current tire
inflation pressure for each tire appears in the
multifunction display after a few minutes of
driving.
iPossible differences between the
readings of a tire pressure gauge of an air
hose, e.g. gas station equipment, and the
vehicle’s control system can occur. The tire
pressure displayed by the control system
apply to sea level. In high-altitude
locations, the reading on a tire pressure
gauge will be higher than the reading issued
by the vehicle’s control system. Do not
reduce the tire inflation pressure under
such circumstances.
XSwitch on the ignition.XPress button V or U on the
multifunction steering wheel repeatedly
until the standard display appears in the
multifunction display (Y page 99).
XPress button & or * until the current
inflation pressure for each tire appears in
the multifunction display.
When the vehicle has been parked for longer
than 20 minutes, the message Tire
158Tires and wheelsOperation
463_AKB; 2; 52, en-USd2ureepe,Version: 2.11.7.12008-12-02T10:52:11+01:00 - Seite 158

vehicle damage not covered by the
Mercedes-Benz Limited Warranty.
Maintenance service indicator
message
The maintenance service indicator message
will notify you when the next maintenance
service is due.
Service A In XXXXX Miles (km)
Service A In XXX Days
Service A Due Now
The type of maintenance service due is
indicated in the multifunction display:
¯Basic service (A)±Extended service (B)
Refer to Maintenance Booklet for a listing of
maintenance services and intervals they need
to be performed at.
Clearing the maintenance service
indicator message
The maintenance service indicator message
is cleared automatically
Rafter approximately 10 seconds when you
switch on the ignition
Rafter approximately 10 seconds when
reaching the service threshold while driving
Rafter approximately 30 seconds, once the
suggested maintenance service term has
passed
XClearing the maintenance service
indicator message manually: Press reset
button : on the instrument cluster.
The standard display appears in the
multifunction display.
Maintenance service term exceeded
If you have exceeded the suggested
maintenance service term, you will see the
following message in the multifunction
display:
Service A Exceeded By XXXXX Miles
(Km)
In addition, a signal sounds when the
message appears.
Any authorized Mercedes-Benz Center will
reset the maintenance service indicator
following a completed maintenance service.
Calling up the maintenance service
indicator display
iThe menu overview can be found on
(Y page 99).
You can call up the maintenance service
indicator display at any time to check when
the next maintenance service is due.
XSwitch on the ignition.XPress button V or U on the
multifunction steering wheel repeatedly
186MaintenanceOperation
463_AKB; 2; 52, en-USd2ureepe,Version: 2.11.7.12008-12-02T10:52:11+01:00 - Seite 186

XInsert the bulb socket back into side
marker lamp housing ;.
XReinstall dust cover =.XReinstall side marker lamp housing ;.XInstall and tighten securing screws :.
iDo not overtighten securing screws :.
Otherwise side marker lamp housing ;
could be damaged.
Replacing bulbs for rear lamps
Before you start to replace a bulb for a rear
lamp, do the following:
XSwitch off the ignition.XTurn the exterior lamp switch to position
$.
Removing/installing rear lamp guard
(G 55 AMG only)
XRemove screws ;.XSwivel rear lamp guard : outward. Make
sure the guard does not strike painted
surfaces.
XSwivel rear lamp guard : back after
replacing bulbs and fasten it with
screws ;.
Tail lamp unit
XG 55 AMG only: Remove the rear lamp
guard.
Example illustration: Left tail lamp lens (right taillamp lens laterally reversed)
XLoosen and remove securing screws :.XRemove tail lamp lens ;.
Example illustration: Left tail lamp unit (right taillamp unit laterally reversed)
=Turn signal lamp bulb?Brake, tail, parking and standing lamp
bulb
ATail, parking and standing lamp bulbXGently press onto respective bulb =, ?,
or A and turn counterclockwise out of its
bulb socket.
XGently press the new bulb into the bulb
socket and turn clockwise until it engages.
XReinstall tail lamp lens ;.XInstall and tighten securing screws :.230Replacing bulbsPractical hints
463_AKB; 2; 52, en-USd2ureepe,Version: 2.11.7.12008-12-02T10:52:11+01:00 - Seite 230