2009 MERCEDES-BENZ G-Class ignition

still adjusting could cause the driver to lose
control of the vehicle.
Heated steering wheel
The steering wheel heating warms up the
leather area of the steering wheel.
XSwitch on the ignition.XSwitching on: Turn switch at the tip of the
stalk in direction of arrow :.
Indicator lamp = comes on.
iThe steering wheel heating may be
suspended temporarily. However, indicator
lamp = remains on. The steering wheel
heating is suspended when the
temperature of the vehicle interior is above
86‡ (30†). It is also suspended when the
temperature of the steering wheel is above
95‡ (35†).
When these conditions do not apply
anymore, steering wheel heating
continues.
XSwitching off: Turn switch at the tip of
stalk in direction of arrow ;.
Indicator lamp = goes out.
iIndicator lamp = flashes or goes out in
case of power surge or undervoltage or if
the steering wheel heating malfunctions.
iThe steering wheel heating switches off
automatically when you remove the
SmartKey from the starter switch.
For more information on the steering wheel,
see “Multifunction steering wheel”
(Y page 97).
Mirrors
Notes
Adjust the interior and exterior rear view
mirrors before driving so that you have a good
view of the road and traffic conditions.
Interior rear view mirror
XAdjust the interior rear view mirror
manually.
Exterior rear view mirrors
GWarning!
Exercise care when using the passenger-side
exterior rear view mirror. The mirror surface
is convex (outwardly curved surface for a
wider field of view). Objects in mirror are
closer than they appear. Check your interior
rear view mirror and glance over your
shoulder before changing lanes.
XSwitch on the ignition.XPress button = for the driver’s side
exterior rear view mirror or button ; for
the passenger-side exterior rear view
mirror.
Mirrors69Controls in detail463_AKB; 2; 52, en-USd2ureepe,Version: 2.11.7.12008-12-02T10:52:11+01:00 - Seite 69Z

XPress adjustment button : up, down, left
or right according to the desired setting.
! If an exterior rear view mirror was forcibly
hit from the front, manually snap it back
into place.
iAt low ambient temperatures, the exterior
rear view mirrors will be heated
automatically.
Auto-dimming rear view mirrors
The exterior rear view mirror on the driver’s
side and the interior rear view mirror will
respond automatically to glare when the
ignition is switched on and incoming light
from headlamps falls on the sensor in the
interior rear view mirror.
The rear view mirrors will not react if the
automatic transmission is set to reverse gear
R or the interior lighting is switched on.
GWarning!
The auto-dimming function does not react if
incoming light is not aimed directly at sensors
in the interior rear view mirror.
The interior rear view mirror and the exterior
rear view mirror on the driver’s side do not
react, for example, when transporting cargo
which covers the rear window.
Light hitting the mirror(s) at certain angles
(incident light) could blind you. As a result,
you may not be able to observe traffic
conditions and could cause an accident.
Activating exterior rear view mirror
parking position
This feature is only available in Canada
vehicles.
Follow these steps to activate the mirror
parking position so that the passenger-side
exterior rear view mirror will be turned
downward to the stored position.
XMake sure you have stored a parking
position for the passenger-side exterior
rear view mirror (Y page 71).
XSwitch on the ignition.XPress button ; for the passenger-side
exterior rear view mirror.
XShift the automatic transmission into
reverse gear R.
The passenger-side exterior rear view
mirror will be turned downward to the
stored position.
The exterior rear view mirror returns to its
previously stored driving position
R10 seconds after you have put the gear
selector lever out of position reverse gear
R
Rimmediately once your vehicle exceeds a
speed of approximately 6 mph (10 km/h)
Rimmediately when you press button : for
driver’s side exterior rear view mirror
Memory function
Notes
With the memory function you can store up
to three different configurations per front
seat.
Each memory position button on the driver’s
side can store all of the following settings:
RSeat position
RMulticontour seat: previously saved setting
70Memory functionControls in detail
463_AKB; 2; 52, en-USd2ureepe,Version: 2.11.7.12008-12-02T10:52:11+01:00 - Seite 70

RSteering wheel position
RExterior rear view mirrors’ position
GWarning!
Do not activate the memory function while
driving. Activating the memory function while
driving could cause the driver to lose control
of the vehicle.
Each memory position button on the front
passenger side can store all of the following
settings:
RSeat position
RMulticontour seat: previously saved setting
Storing positions into memory
XAdjust the seats.XOn the driver’s side, additionally adjust the
steering wheel and exterior rear view
mirrors to the desired positions.
XPress memory button ;.XPress memory button ; once and within
3 seconds press one memory position
button : 1, 2 or 3.
All settings are stored to the selected
position.
Recalling positions from memoryXPress and hold desired memory position
button 1, 2 or 3 until the seat has
completely moved to the stored position.
On the driver’s side, also wait for the
steering wheel and exterior rear view
mirrors to move to the stored position.
iReleasing the memory position button
stops movement to the stored positions
immediately.
Storing exterior rear view mirror
parking position
This feature is only available in Canada
vehicles.
For easier parking, you can adjust the
passenger-side exterior rear view mirror so
that you can see the right rear wheel as soon
as you engage reverse gear R.
For information on activating the parking
position, see (Y page 70).
XStop the vehicle.XSwitch on the ignition.XPress button =.
The passenger-side exterior rear view
mirror is selected.
XAdjust the passenger-side exterior rear
view mirror with adjustment button : so
that you see the rear wheel and the road
curb.
Memory function71Controls in detail463_AKB; 2; 52, en-USd2ureepe,Version: 2.11.7.12008-12-02T10:52:11+01:00 - Seite 71Z

High beam XTurn the exterior lamp switch to position
L (Y page 72).
XSwitching on: Push the combination
switch in direction of arrow :.
The high-beam headlamp indicator lamp
K in the instrument cluster comes on.
XSwitching off: Pull the combination switch
in direction of arrow ; to its original
position.
High-beam flasher
XSwitching on: Pull the combination switch
briefly in direction of arrow ;.
Turn signals
XPress the combination switch in direction
of arrow : or ;.
The corresponding turn signal indicator
lamp ! or # in the instrument
cluster flashes.
The combination switch resets automatically
after major steering wheel movements.
iTo signal minor directional changes such
as changing lanes, press combination
switch only to point of resistance and
release. The corresponding turn signal
lamps will flash three times.
Hazard warning flasher
The hazard warning flasher can be switched
on at all times, even with the SmartKey
removed from the starter switch.
The hazard warning flasher comes on
automatically when an air bag deploys.
XSwitching on: Press hazard warning
flasher switch :.
All turn signal lamps are flashing.
iWith the hazard warning flasher activated
and the combination switch set for either
left or right turn, only the respective left or
right turn signals will operate when the
ignition is switched on.
XSwitching off: Press hazard warning
flasher switch : again.
iIf the hazard warning flasher has been
activated automatically, press hazard
warning flasher switch : to switch it off.
Headlamp cleaning system
Lighting75Controls in detail463_AKB; 2; 52, en-USd2ureepe,Version: 2.11.7.12008-12-02T10:52:11+01:00 - Seite 75Z

Switching cargo compartment lamps
off and on with the tailgate open
GWarning!
To prevent possible personal injury, always
keep hands and fingers away from the cargo
compartment opening when closing the
tailgate. Be especially careful when small
children are around.
GWarning!
Make sure the tailgate is closed when the
engine is running and while driving. Among
other dangers, deadly carbon monoxide (CO)
gases may enter vehicle interior resulting in
unconsciousness and death.
! To prevent the vehicle battery from being
discharged, switch off the cargo
compartment lamps if the tailgate should
remain open for a longer period of time.
Switching off
XOpen the tailgate (Y page 61).XPress door lock : down in direction of
arrow until it engages.
! Do not close the tailgate if the lock is
engaged in down position. The lock could
otherwise be damaged.
When locking the tailgate, it is important
that the door lock be in the same original
position as shown in the illustration.
To return door lock : to its original
position, press lock cylinder ;.
Switching onXPress lock cylinder ; to activate the cargo
compartment lamps again.
The cargo compartment lamps will come
on.
Wipers
Notes
! Do not operate the wipers when the
windshield/rear window is dry. Dust that
accumulates on a windshield/rear window
might scratch the glass and/or damage the
wiper blades when wiping occurs on a dry
windshield/rear window. If it is necessary
to operate the wipers in dry weather
conditions, always operate the wipers with
washer fluid.
Combination switch
:Single wipeWiping with washer fluid;Switching on windshield wipersXSwitch on the ignition.
Windshield wipers
Switching on/off
0Windshield wipers offIIntermittent wipingWipers79Controls in detail463_AKB; 2; 52, en-USd2ureepe,Version: 2.11.7.12008-12-02T10:52:11+01:00 - Seite 79Z

:Override switch (Y page 49);Left front door window=Right front door window?Right rear door windowALeft rear door windowXSwitch on the ignition.XOpening/closing: Press or pull and hold
switch ; to A to the resistance point.
The corresponding door window will move
downwards or upwards until you release
the switch.
XExpress opening: Press switch ; to A
past the resistance point and release.
The corresponding door window opens
completely.
XStopping during express opening: Press
or pull the respective switch again.
Summer opening feature
When the weather is warm, you can ventilate
the vehicle before driving off by
simultaneously
Ropening the windows
Ropening the tilt/sliding sunroof
The summer opening feature can only be
activated via the remote control of the
SmartKey. The SmartKey must be in close
proximity to the driver’s outside door handle.
XAim transmitter eye of the SmartKey at the
driver’s outside door handle.
XPress and hold button % on the
SmartKey until the windows and the tilt/
sliding sunroof have reached the desired
position.
The vehicle unlocks.
XRelease button % on the SmartKey to
interrupt the opening procedure.
Convenience closing feature
When locking the vehicle, you can
simultaneously close the windows and the
tilt/sliding sunroof.
GWarning!
When closing the windows and the tilt/sliding
sunroof, make sure there is no danger of
anyone being harmed by the closing
procedure.
If potential danger exists, proceed as follows:
RRelease button & to stop the closing
procedure. To open, press and hold button
%. To continue the closing procedure
after making sure that there is no danger of
anyone being harmed by the closing
procedure, press and hold button &.
The SmartKey must be in close proximity to
the driver’s outside door handle.
XAim transmitter eye of the SmartKey at the
driver’s outside door handle.
XPress and hold button & on the
SmartKey until the windows and the tilt/
sliding sunroof are completely closed.
XRelease button & on the SmartKey to
interrupt the closing procedure.
Driving and parking
Safety notes
GWarning!
Make sure absolutely no objects are
obstructing the pedals’ range of movement.
Keep the driver’s footwell clear of all
obstacles. If there are any floormats or
82Driving and parkingControls in detail
463_AKB; 2; 52, en-USd2ureepe,Version: 2.11.7.12008-12-02T10:52:11+01:00 - Seite 82

RTurn the SmartKey in the starter switch to
position 0 and remove the SmartKey from
the starter switch.
RTake the SmartKey with you and lock the
vehicle when leaving.
Parking brake
GWarning!
Engaging the parking brake while the vehicle
is in motion can cause the rear wheels to lock
up. You could lose control of the vehicle and
cause an accident. In addition, the vehicle’s
brake lights do not light up when the parking
brake is engaged.
GWarning!
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it with
you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. Children could
release the parking brake and/or shift the
automatic transmission out of park position
P, either of which could result in an accident
and/or serious personal injury.
XReleasing: Pull up slightly on parking brake
lever : and press release button ;.
XPush parking brake lever : down to its
original position.
When the ignition is switched on or the
engine is running, the brake warning lamp
$ (USA only) or J (Canada only) in
the instrument cluster goes out.
XEngaging: Pull up parking brake lever :
firmly.
When the engine is running, the brake
warning lamp $ (USA only) or J
(Canada only) in the instrument cluster
comes on.
Turning off the engine
GWarning!
Do not turn off the engine before the vehicle
has come to a complete stop. With the engine
not running, there is no power assistance for
the brake and steering systems. In this case,
it is important to keep in mind that a
considerably higher degree of effort is
necessary to brake and steer the vehicle.
XShift the automatic transmission into park
position P.
XEngage the parking brake.
iAlways engage the parking brake in
addition to shifting the automatic
transmission into park position P.
When parked on an incline, also turn the
front wheels towards the road curb.
XTurn the SmartKey in the starter switch to
position 0.
XRemove the SmartKey from the starter
switch.
The immobilizer is activated.
The SmartKey can only be removed from the
starter switch with the automatic
transmission in park position P.
86Driving and parkingControls in detail
463_AKB; 2; 52, en-USd2ureepe,Version: 2.11.7.12008-12-02T10:52:11+01:00 - Seite 86

XPress button & or *.
The stored messages will now be displayed
in the order in which they have occurred.
For malfunction and warning messages,
see “Vehicle status messages in the
multifunction display” (Y page 196).
iAfter you have scrolled through all
recorded status messages, the first
recorded message appears again.
Should the vehicle’s system record any
conditions while driving, the number of
messages will reappear in the multifunction
display when the SmartKey in the starter
switch is turned to position 0 or removed
from the starter switch.
Except for high-priority messages, the vehicle
status message memory will be cleared when
you switch off the ignition.
Settings menu
Introduction
In the Settings menu there are two
functions: The function To reset: Press
reset button for 3 secs., with which you
can reset all the settings to the original
factory settings and a collection of submenus
with which you can make individual settings
for your vehicle.
The following settings and submenus are
available in the Settings menu:
RResetting to factory settings
(Y page 103)
RSubmenus in the Settings menu
(Y page 104)
RInstrument cluster submenu
(Y page 104)
RLighting submenu (Y page 106)
RVehicle submenu (Y page 108)
RConvenience submenu (Y page 108)
Resetting to factory settings
You can reset the functions of all submenus
to the factory settings.
For safety reasons, the function Headlamp
Mode in the Lighting submenu cannot be
reset while driving.
The following message appears in the
multifunction display: Cannot be
completely reset to factory
settings while driving.
XPress button V or U repeatedly until
the Settings menu appears in the
multifunction display.
XPress the reset button in the instrument
cluster (Y page 95) for approximately
3 seconds.
The request to press the reset button once
more to confirm appears in the
multifunction display.
XPress the reset button once more.
The functions of all the submenus will be
reset to factory settings.
Control system103Controls in detail463_AKB; 2; 52, en-USd2ureepe,Version: 2.11.7.12008-12-02T10:52:11+01:00 - Seite 103Z