2009 MERCEDES-BENZ E-CLASS COUPE Owners Manual

X
Insert bulbh older0047and turn it clockwise.
X Align housing cover 0046and turn it clock-
wise.
Main-beam headlamps (halogen head-
lamps)/cornering lamp* (Intelligent
Light System*) X
Switch off the lights.
X Open the bonnet.
X Turn housing cover 0046anti-clockwise and
remove it.
X Turn bulbh older0047anti-clockwise and
remove it.
X Remove the bulbf rom bulbholder0047.
X Insert the new bulbi nto bulbholder0047.
X Insert bulbh older0047and turn it clockwise.
X Align housing cover 0046and turn it clock-
wise.
Side lamp/parking lamp (halogen head-
lamps) X
Switch off the lights.
X Open the bonnet.
X Turn housing cover 0046anti-clockwise and
remove it.
X Pullo ut bulbh older0047.
X Remove the bulbf rom bulbholder0047.
X Insert the new bulbi nto bulbholder0047.
X Insert bulbh older0047.
X Align housing cover 0046and turn it clock-
wise.
Turn signal lamp (halogen headlamps) Due to their location, have the bulbs in the
left-hand headlamp changed at
aqualified
specialist workshop, e.g. aMercedes-Benz
Service Centre.
X Switch off the lights.
X Open the bonnet.
X Turn bulbh older0046anti-clockwise and
remove it.
X Turn the bulba nti-clockwise, applying
slight pressure, and remove it from bulb
holder 0046.
X Insert the new bulbi nto bulbholder0046and
turn it clockwise.
X Insert bulbh older0046and turn it clockwise. 262
Changing bulbsPractical advice
*o
ptional
207_AKB; 2; 3, en-GB
mkalafa
,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 262

Replacing the wiper blades
G
Ris
kofa ccident
The windscreen will not longer be wiped prop-
erl yift he wiper blades are worn. Thi scould
prevent yo ufrom observing the traffic condi-
tions ,thereby causing an accident. Replace
the wiper blades twice ayear, ideall yinspring
and autumn. G
Ris
kofa ccident
The wiper arm scould star tmoving and cause
an injury if yo uleave the windscreen wipers
switched on.
Remove the key from the ignition lock before
replacing the wiper blades.
! To avoid damaging the windscreen wiper
blades, make sure that yo utouch only the
wiper arm of the windscreen wiper. To remove
X Remove the key from the ignition lock or
turn the key to position 0(KEYLESS-GO).
X Fol dthe wiper arm away from the wind-
screen unti litengages.
X Set the wiper blad eatright angle stothe
wiper arm. X
Remove the wiper blad efrom the retainer
on the wiper arm in the direction of the
arrow. Fitting
X Slide the new wiper blad einto the retainer
on the wiper arm in the opposite direction
to the arrow.
X Turn the wiper blad eparalle ltot he wiper
arm.
X Fol dthe wiper arm back onto the wind-
screen. Flat tyre
Flat tyre equipmen
tvariants
Your vehicl emay be equipped with:
R aT IREFIT kit (Y page 207)
R a" Minispare" emergency spare wheel*
(Y page 208)
R the MOExtended run-flat sys-
tem* (Y page 272) Preparing the vehicle
i Vehicl epreparation is not necessary on
vehicles with MOE tyres*.
X Stop the vehicl easfar away as possible
from traffic on solid ,non-slipper yand level
ground.
X Switch on the hazard warning lamps.
X Firmly depres sthe parking brake.
X Vehicles with manual transmission:
engage firs torreverse gear.
X Vehicles with automati ctransmis-
sion*: move the selector lever to P.
X All occupants mus tget ou tofthe vehicle.
Make sure that they are not endangered as
they get ou tofthe vehicle.
X Make sure that no one is nea rthe danger
are aw hilst awheel is being changed .Any-
one wh oisnot directl yassisting in the
wheel change should, for example, stand
behind the barrier.
X Switch off the engine. Flat tyre
263Practical advice
*optional
207_AKB; 2; 3, en-GB
mkalafa
,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 263 Z

X
Vehicles withou tKEYLESS GO*:remove
the key from the ignition lock.
X Vehicles with KEYLES SGO*: openthe
driver' sdoor.
The on-board electronics have status 0,
which is the same as the key having been
removed.
X Ge toutof the vehicle.
X Close the driver' sdoor.
X Place the warning triangl e(Ypage 206) at
as uitabl edistance. Observe lega lrequire-
ments. Usin
gthe TIREFI Tkit
Yo uc an us ethe TIREFIT kit to sea lsmall
punctures, particularly thos einthe tyre tread.
Yo uc an us eTIREFIT at outsid etemperatures
dow nto- 20†. G
Risk of accident
In the following case syoursafety is especially
endangered, as tyre sealant is insufficient if:
R there are cuts or puncture sinthe tyre
greater than 4mm.
R the wheel rim is damaged.
R youh aved riven at very low tyre pressures
or on aflatt yre.
Do not drive any further. Consul taqualified
specialist worksho pwhich ha sthe necessary
specialist knowledg eand tool stocarryo ut
the work required.
Mercedes-Benz recommend sthat yo uuse a
Mercedes-Benz Service Centre for this pur-
pose. In particular, work relevant to safety or
on safety-related systems mus tbec arrie dout
at aq uali fied specialist workshop.
X Do not remove any foreign objects which
have penetrated the tyre ,e.g. screw sor
nails.
X Remove the TIREFIT kit, the accompanying
"max. 80 km/h "sticke rand the electri cair
pump from the stowag ewellu nderneath the luggage compartment floor
(Y
page 207). X
Affix part 0046of the sticke rwithin the driv-
er's field of vision.
X Affix part 0047of the sticke rnearthe valve
on the wheel with the defectiv etyre. G
Risk of injury
TIREFIT mus tnot come into contact with your
skin, eyes or clothing.
R If TIREFIT come sinto contact with your
eyes or skin, immediatel yrinse thoroughly
with clean water.
R Change ou tofclothing which ha scome into
contact with TIREFIT immediately.
R If an allergi creaction occurs, consult adoc-
tor immediately.
Kee pTIREFIT away from children.
R If TIREFIT is swallowed, immediatel yrinse
your mouth ou tthoroughly and drink plenty
of water.
R Do not induce vomiting. Consul tadoctor
immediately.
R Do not inhale TIREFIT fumes.
i If TIREFIT leaks out, allow it to dry .Itcan
then be removed like alayer of film.
If yo uget TIREFIT on your clothing, have it
cleane dassoona spossible with perchloro-
ethylene. 264
Flat tyrePractical advice
*o
ptional
207_AKB
;2;3,en-GB
mkalafa ,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 264

G
Risk of injury
Compl ywitht he manufacturer' ssafety
instructions shown on the sticke ronthe elec-
tric ai rpum p.
You rvehicle may be equipped with one of two
different ai rpum ps. Version 1can be identi-
fie dbyt he flap, behind which the hos ewith
the pressure gaug eand cable are located;
version 2hasap ressure gaug eintegrate din
the electri cairpump.
Version 1 X
Ope nflap 0047on the electri cairpump.
X Pull connector 0086with cable and ai rpump
hose 0087outoft he housing.
X Screw ai rpum phose 0087onto flange 006Eof
TIREFIT sealant fille rbottle 0046.
X Place TIREFIT sealant fille rbottle 0046head
downwards into recess 008Aof the electric
ai rp um p. X
Remove the cap from valve 0070on the faulty
tyre. X
Make sure pressure release screw 0071on
pressure gauge 0072is fully closed.
X Screw fille rhose 006Fonto valve 0070.
X Inser tconnector 0086into the socke tofthe
cigarette lighter* (Y page 173) or into a
12 Vp ower socke t(Ypage 174) in your
vehicle.
X Vehicles without KEYLES SGO*: turn the
key to position 2(Y page 65) in the ignition
lock.
X Vehicles with KEYLES SGO*: press the
Start/Stop button twice (position
2 (Y page 66)).
X Press on/off switch 0088on the electri cair
pump to I.
The electri cairpump is switched on. The
tyre is inflated.
i First, TIREFIT is pumpe dinto the tyre .The
pressure can briefl yrisetoa round 5bar.
Do no tswitcho ff the electric pump dur-
ing this phase.
X Let the electri cpum prun for five minutes.
The tyre shoul dthen have apressure of at
leas t1.8 bar.
! Do not operate the electri cairpump for
longer than eight minutes at atime without
ab reak. It may otherwise overheat.
The ai rpum pcan be operate dagain once
it ha scooled down. Flat tyre
265Practical advice
*optional
207_AKB
;2;3,en-GB
mkalafa ,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 265 Z

If
ap ressure of 1. 8bar is not reached
after fiv eminutes:
X Switch off and disconnect th eelectric air
pump and driv ethe vehicle forwards or
backwards approximately 10 m.
This distributes th eTIREFI Tmoree venly.
X Pump up th etyrea gain. G
Ris
kofa ccident
If ap ressur eof1.8bar is no tachieve dafter
fiv em inutes, th etyreist oobadly damaged.
Do no tdrivea ny further. Consult aqualified
specialist worksho pwhichh as th enecessary
specialist knowledge and tools to carry out
th ew ork required .Mercedes-Ben zrecom-
mends that you use aMercedes-Ben zService
Centr efor this purpose. In particular, work
relevan ttosafety or on safety-related sys-
tems must be carried out at aqualified spe-
cialist workshop.
When atyrep ressure of at leas t1.8bar
is reached:
X Press on/off switch 0088on th eelectric air
pump to 0.
The electric air pump is switched off.
X Remove th eTIREFI Tkit from th ewheel.
! Afte ruse, exces sTIREFI Tmay run out of
th ef ille rhose. This may caus estains.
Therefore, plac ethe fille rhoseint heplastic
whic hcontai nedt he TIREFI Tkit.
X Stow away th eTIREFI Tkit,t he electric air
pump and th ewarning triangle.
X Pul lawa yimm ediately.
X Stop after driving for approximately ten
minute sand check th etyrep ressur ewith
th ee lectric air pump. G
Ris
kofa ccident
If th etyrep ressur eisnowlower than 1. 3bar,
th et yreist oobadly damaged. Do no tdrive
any further. Consult aqualified specialist
worksho pwhichh as th enecessary specialist
knowledge and tools to carry out th ework required
.Mercedes-Ben zrecommends that
you use aMercedes-Ben zServic eCentr efor
this purpose. In particular, work relevan tto
safety or on safety-related systems must be
carried out at aqualified specialist workshop.
X If th etyrep ressur eisstill at least 1. 3bar,
correct it (see fuel fille rflap for values).
To increase th etyrep ressure: switch on
th ee lectric air pump.
To reduce th etyrep ressure: open pres-
sure release screw 0071on pressure
gauge 0072.
X Drive to th eneares tworksho pand have the
tyr ec hanged there.
X Hav ethe TIREFI Tkit replace dassoonas
possible at aqualified specialist workshop,
e.g. at aMercedes-Ben zServic eCentre. G
Ris
kofa ccident
Do no texcee dt he maximum spee dof
80 km/h.
The "max .80km/h" label must be affixe din
th ed river' sfieldofv ision.
The vehicle's handlin gcharacteristic smay be
affected. H
Environmental note
Hav ethe used TIREFI Tkit disposed of profes-
sionally, e.g. at aMercedes-Ben zService
Centre.
X Hav ethe TIREFI Tkit replace devery four
years at aqualified specialist workshop,
e.g. aMercedes-Ben zServic eCentre. 266
Flat tyrePractical advice
207_AKB
;2;3,en-GB
mkalafa ,V ersion: 2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 266

Versio
n2 X
Pull connector 0088with cable and ai rpump
hose 0086outoft he housing.
X Screw ai rpum phose 0086onto flange 0087of
TIREFIT sealant fille rbottle 0046.
X Place TIREFIT sealant fille rbottle 0046 head
downwards into recess 0047of the electric
ai rp um p. X
Remove the cap from valve 006Eon the faulty
tyre.
X Screw fille rhose 006Fonto valve 006E.
X Insert connector 0088into the socke tofthe
cigarette lighter* (Y page 173) or into a
12 Vp ower socke t(Ypage 174) in your
vehicle.
X Vehicles withou tKEYLESS GO*:turn the
key to position 2(Y page 65) in the ignition
lock.
X Vehicles with KEYLES SGO*: press the
Start/Sto pbutton twice (position
2 (Y page 66)). X
Press on/of fswitch 008Aon the electri cair
pump to I.
The electri cairpump is switched on. The
tyr eisi nflated.
i First, TIREFIT is pumpe dinto the tyre. The
pressure can briefl yrisetoa round 5bar.
Do no tswitcho ff the electric pump dur-
in gt his phase.
X Let the electri cpum prun for fiv eminutes.
The tyr eshoul dthen have apressure of at
leas t1.8 bar.
! Do not operate the electri cairpump for
longer tha neight minutes at atime without
ab reak. It ma yotherwise overheat.
The ai rpum pcan be operated agai nonce
it ha scooled down.
If ap ressure of 1.8 bar is no treached
afte rfivem inutes:
X Switch off and disconnect the electri cair
pump and drive the vehicl eforwards or
backwards approximatel y10m.
Thi sd istributes the TIREFIT more evenly.
X Remove TIREFIT sealant fille rbottle 0046
from the electri cpum p.
X Pump up the tyr eagain. G
Ris
kofa ccident
If ap ressure of 1.8 ba risnot achieved after
fiv em inutes, the tyr eistoo badl ydam aged.
Do not drive any further .Consult aquali fied
specialist workshop which ha sthe necessary
specialist knowledge and tool stocarry out
the work required .Mercedes-Benz recom-
mend stha tyou useaM ercedes-Benz Service
Centre for thi spurpose. In particular, work
relevant to safety or on safety-relate dsys-
tems must be carrie doutataq uali fied spe-
cialist workshop. Flat tyre
267Practical advice
*optional
207_AKB; 2; 3, en-GB
mkalafa,
Version: 2.11.8.1 2009-07-23T10:23:49+02:00-Seite 267 Z

When
atyre pressure of at leas t1.8 bar
is reached:
X Press on/off switch 008Aon the electric air
pump to 0.
The electric air pump is switched off.
X Remove the TIREFIT kit from the wheel.
! After use,e xcess TIREFIT may run out of
the filler hose. This may caus estains.
Therefore, place the filler hose in the plastic
which contained the TIREFIT kit.
X Stow away the TIREFIT kit, the electric air
pump and the warning triangle.
X Pull away immediately.
X Stop after driving for approximately ten
minutes and check the tyre pressure with
the electric air pump. G
Risk of accident
If the tyre pressure is now lower than 1.3 bar,
the tyre is too badly damaged. Do not drive
any further. Consult aqualified specialist
worksho pwhich has the necessary specialist
knowledge and tools to carry out the work
required .Mercedes-Benz recommends that
you use aMercedes-Benz Service Centre for
this purpose. In particular, work relevant to
safety or on safety-related systems must be
carrie dout at aqualified specialist workshop. X
If the tyre pressure is still at least 1.3 bar,
correct it (see fuel filler flap for values).
To increase the tyre pressure: switch on
the electric air pump. To reduce the tyre pressure:
press pres-
sure release button 0070next to pressure
gauge 0071.
X Drive to the neares tworksho pand have the
tyre changed there.
X Have the TIREFIT kit replaced as soon as
possible at aqualified specialist workshop,
e.g. at aMercedes-Benz Service Centre. G
Risk of accident
Do not exceed the maximu mspee dof
80 km/h.
The "max. 80 km/h" label must be affixe din
the driver's fiel dofvision.
The vehicle's handling characteristics may be
affected. H
Environmental note
Have the use dTIREFIT kit disposed of profes-
sionally ,e.g. at aMercedes-Benz Service
Centre.
X Have the TIREFIT kit replaced every four
years at aqualified specialist workshop,
e.g. aMercedes-Benz Service Centre. Changing
awheel and fitting the
spare wheel* G
Risk of accident
The whee ldimensions and tyre size of the
"Minispare" emergency spare wheel* may dif-
fer from those of the damaged wheel.
You rvehicle's handling characteristics will
change when a"Minispare" emergency spare
wheel* is fitted. Adapt you rstyle of driving
accordingly.
The "Minispare" emergency spare wheel*
may only be use dfor as hort time. Do not
exceed the maximu mspee dof80k m/h and
do not deactivate ESP ®
.
Never drive the vehicl ewith more than one
"Minispare" emergency spare wheel* fitted. 268
Flat tyrePractical advice
*o
ptional
207_AKB; 2; 3, en-GB
mkalafa,
Version: 2.11.8.1 2009-07-23T10:23:49+02:00-Seite 268

G
Risk of accident
Have the collapsible emergency spare
wheel *replaced with anew wheel as soon as
possible at aqualified specialist workshop
which has the necessary specialist knowledge
and tools to carry out the work required.
Mercedes-Benz recommends that you use a
Mercedes-Benz Service Centr efor this pur-
pose. In particular, work relevant to safety or
on safety-related systems must be carried out
at aq ualified specialist workshop.
Preparing the vehicle i
Vehicles without aspare wheel* are not
equipped with wheel-changing tools at the
factory. For more information on which
tools are required to perform awheel
change on your vehicle, e.g. wheel chock,
centring pin or wheel wrench, consult a
Mercedes-Benz Service Centre.
X Prepare the vehicle as described
(Y page 263).
X Ifat railer is coupled to the vehicle, uncou-
ple it.
X Brin gthe wheels into the straight-ahead
position.
X Remove the following items from the stow-
age well under the boot floor:
R
the "Minispare" emergency spare
wheel*
R the vehicle tool kit
R the folding wheel chock
R the jack
Use the folding wheel choc ktopreventthe
vehicle from rolling away. X
Fold both plates 0046upwards.
X Fold out lower plate 0047.
X Guide the lugs on the lower plate fully into
opening sinbase plate 008A. Securin
gthe vehicle on level ground
X On level ground: place the folding wheel
choc kora similar item under the wheel that
is diagonally opposite to the wheel you wish
to change. Securin
gthe vehicle on slight downhill gradients Flat tyre
269Practical advice
*optional
207_AKB
;2;3,en-GB
mkalafa, Version:2.11.8.1
2009-07-23T10:23:49+02:00
-Seite 269 Z