2009 INFINITI QX56 Abs

C1143, C1144 STEERING ANGLE SENSORBRC-63
< COMPONENT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Always perform neutral position adjustment for the st eering angle sensor when replacing the ABS actuator
and electric unit (control unit). Refer to BRC-8, "
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
POSITION : Description".
>> GO TO 2
2.CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replacing the ABS actuator and electric unit (control unit).
Refer to BRC-9, "
CALIBRATION OF DECEL G SENSOR : Description".
>> END
Revision: December 20092009 QX56

BRC-64
< COMPONENT DIAGNOSIS >[VDC/TCS/ABS]
C1155 BRAKE FLUID LEVEL SWITCH
C1155 BRAKE FLUID LEVEL SWITCH
DescriptionINFOID:0000000003772566
The brake fluid level switch converts the brake fluid level to an electric signal and transmits it to the ABS actu-
ator and electric unit (control unit).
DTC LogicINFOID:0000000003772567
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES >> Proceed to diagnosis procedure. Refer to BRC-64, "Diagnosis Procedure".
NO >> Inspection End
Diagnosis ProcedureINFOID:0000000003772568
INSPECTION PROCEDURE
1.CONNECTOR INSPECTION
1. Disconnect ABS actuator and electric unit (control unit) connector E125 and brake fluid level switch con- nector E21.
2. Check the terminals for deformati on, disconnection, looseness or damage.
Is the inspection result normal?
YES >> GO TO 2
NO >> Repair or replace as necessary.
2.CHECK HARNESS BETWEEN BRAKE FLUID LEVE L SWITCH AND ABS ACTUATOR AND ELECTRIC
UNIT (CONTROL UNIT)
1. Check continuity between ABS actuator and electric unit (control
unit) harness connector E125 (A) and brake fluid level switch
harness connector E21 (B).
2. Check continuity between ABS ac tuator and electric unit (control
unit) harness connector E125 (A) and ground.
Is the inspection result normal?
DTC Display item Malfunction detected condition Possible cause
C1155 BR FLUID LEVEL LOW Brake fluid level is low or communication line between
the ABS actuator and electric unit (control unit) and brake
fluid level switch is open or shorted. • Harness or connector
• Brake fluid level switch
•Brake fluid level
Self-diagnosis results
BR FLUID LEVEL LOW
ABS actuator and electric unit (control unit) Brake fluid level switch
Continuity
Connector Terminal Connector Terminal
A: E125 8B: E21 1Yes
ABS actuator and electric unit (control unit) —Continuity
Connector Terminal
A: E125 8Ground No
AWFIA0025ZZ
Revision: December 20092009 QX56

C1155 BRAKE FLUID LEVEL SWITCHBRC-65
< COMPONENT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
YES >> GO TO 3
NO >> Repair or replace malfunctioning components.
3.CHECK BRAKE FLUID LEVEL SWITCH GROUND
Check continuity between brake fluid level switch harness connector
E21 and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace malfunctioning components.
4.CHECK BRAKE FLUID LEVEL SWITCH
Check continuity between brake fluid level switch terminals.
Is the inspection result normal?
YES >> Perform self-diagnosis again. If the same results appear, replace ABS actuator and electric unit (control unit). Refer to BRC-116, "
Removal and
Installation".
NO >> Replace brake fluid level switch.
Component InspectionINFOID:0000000003772569
1.CHECK BRAKE FLUID LEVEL SWITCH
1. Turn ignition switch OFF.
2. Disconnect brake fluid level switch connector.
3. Check continuity between brake fluid level switch terminals.
Is the inspection result normal?
YES >> Inspection End
NO >> Replace brake fluid level switch.
Special Repair RequirementINFOID:0000000003772570
1.ADJUSTMENT OF STEERING AN GLE SENSOR NEUTRAL POSITION
Always perform neutral position adjustment for the st eering angle sensor when replacing the ABS actuator
and electric unit (control unit). Refer to BRC-8, "
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
POSITION : Description".
Brake fluid level switch
—Continuity
Connector Terminal
E21 2Ground Yes
AWFIA0026ZZ
Brake fluid level switch
ConditionContinuity
Te r m i n a l
1 − 2 When brake fluid is full in the reser-
voir tank.
No
When brake fluid is empty in the
reservoir tank. Ye s
ALFIA0026ZZ
Brake fluid level switch
ConditionContinuity
Te r m i n a l
1 − 2 When brake fluid is full in the reser-
voir tank.
No
When brake fluid is empty in the
reservoir tank. Ye s
ALFIA0026ZZ
Revision: December 20092009 QX56

BRC-66
< COMPONENT DIAGNOSIS >[VDC/TCS/ABS]
C1155 BRAKE FLUID LEVEL SWITCH
>> GO TO 2
2.CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replac ing the ABS actuator and electric unit (control unit).
Refer to BRC-9, "
CALIBRATION OF DECEL G SENSOR : Description".
>> END
Revision: December 20092009 QX56

C1156 ST ANG SEN COM CIRBRC-67
< COMPONENT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1156 ST ANG SEN COM CIR
DescriptionINFOID:0000000003772571
The steering angle sensor is connected to the ABS actuat or and electric unit (control unit) in addition to CAN
lines. CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle
multiplex communication line with high data communication speed and excellent error detection ability. Many
electronic control units are equipped onto a vehicle, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less
wiring. Each control unit transmits/receives data but selectively reads required data only.
DTC LogicINFOID:0000000003772572
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES >> Proceed to diagnosis procedure. Refer to BRC-67, "Diagnosis Procedure".
NO >> Inspection End
Diagnosis ProcedureINFOID:0000000003772573
INSPECTION PROCEDURE
1.CHECK CONNECTOR
1. Turn ignition switch OFF and disconnect ABS actuat or and electric unit (control unit) connector E125,
check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or
replace terminal.
2. Reconnect connector and perform self-diagnosis.
Is above displayed on the self-diagnosis display?
YES >> Refer to LAN-14, "Trouble Diagnosis Flow Chart".
NO >> Inspection End
DTC Display item Malfunction detected condition Possible cause
C1156 ST ANG SEN COM CIR When steering angle sensor is not transmitting CAN
communication signal to th
e ABS actuator and electric
unit (control unit). • Harness or connector
• CAN communication line
• Steering angle sensor
• ABS actuator and electric unit
(control unit)
Self-diagnosis results
ST ANG SEN COM CIR
Self-diagnosis results
CAN COMM CIRCUIT
ST ANG SEN COM CIR
Revision: December 20092009 QX56

BRC-68
< COMPONENT DIAGNOSIS >[VDC/TCS/ABS]
C1160 DECEL G SEN SET
C1160 DECEL G SEN SET
DescriptionINFOID:0000000003772574
The yaw rate/side/decel G sensor detects the yaw rate
/side/decel G affecting the vehicle, and transmits the
data to the ABS actuator and electric uni t (control unit) as an analog voltage signal.
DTC LogicINFOID:0000000003772575
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES >> Proceed to diagnosis procedure. Refer to BRC-68, "Diagnosis Procedure".
NO >> Inspection End
Diagnosis ProcedureINFOID:0000000003772576
INSPECTION PROCEDURE
1.PERFORM SELF-DIAGNOSIS
Perform ABS actuator and electric unit (control unit) self-diagnosis.
Do self-diagnosis results indicate anything other than shown above?
YES >> Perform repair or replacement for the item indicated.
NO >> Perform calibration of decel G sensor. Refer to BRC-9, "
CALIBRATION OF DECEL G SENSOR :
Description". GO TO 2
2.PERFORM SELF-DIAGNOSIS AGAIN
1. Turn the ignition switch to OFF and then to ON and erase self-diagnosis results.
2. Perform ABS actuator and electric unit (control unit) self-diagnosis again.
Are any self-diagnosis results displayed?
YES >> Replace yaw rate/side/decel G sensor. Refer to BRC-119, "Removal and Installation".
NO >> Inspection End
DTC Display item Malfunction detected condition Possible cause
C1160 DECEL G SEN SET ABS decel G sensor adjustment is incomplete. • Decel G sensor calibration
• Yaw rate/side/decel G sensor
• ABS actuator and electric unit
(control unit)
Self-diagnosis results
DECEL G SEN SET
Self-diagnosis resultsDECEL G SEN SET
Revision: December 20092009 QX56

C1163 ST ANGLE SEN SAFEBRC-69
< COMPONENT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1163 ST ANGLE SEN SAFE
DescriptionINFOID:0000000003772577
The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel,
and transmits the data to the ABS actuator and el ectric unit (control unit) via CAN communication.
DTC LogicINFOID:0000000003772578
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES >> Proceed to diagnosis procedure. Refer to BRC-69, "Diagnosis Procedure".
NO >> Inspection End
Diagnosis ProcedureINFOID:0000000003772579
INSPECTION PROCEDURE
1.ADJUSTMENT OF STEERING AN GLE SENSOR NEUTRAL POSITION
Adjust steering angle sensor neutral position. Refer to BRC-8, "
ADJUSTMENT OF STEERING ANGLE SEN-
SOR NEUTRAL POSITION : Description".
>> GO TO 2
2.INDICATOR LAMP CHECK
Check that VDC OFF indicator lamp is off.
Is VDC OFF indicator lamp off?
YES >> Inspection End
NO >> Perform ABS actuator and electric uni t (control unit) self-diagnosis. Refer to BRC-24, "
CONSULT-
III Function (ABS)".
DTCDisplay item Malfunction detected condition Possible cause
C1163 ST ANGL SEN SAFE When steering angle sensor is in safe mode. • Adjust steering angle sensor
neutral position
Self-diagnosis results
ST ANGL SEN SAFE
Revision: December 20092009 QX56

BRC-70
< COMPONENT DIAGNOSIS >[VDC/TCS/ABS]
C1164, C1165, C1166
, C1167 CV/SV SYSTEM
C1164, C1165, C1166, C1167 CV/SV SYSTEM
DescriptionINFOID:0000000003772580
CV1, CV2 (CUT VALVE)
The cut valve shuts off the normal brake fluid path from the master cylinder, when VDC/TCS is activated.
SV1, SV2 (SUCTION VALVE)
The suction valve supplies the brake fluid from the ma ster cylinder to the pump, when VDC/TCS is activated.
DTC LogicINFOID:0000000003772581
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES >> Proceed to diagnosis procedure. Refer to BRC-70, "Diagnosis Procedure".
NO >> Inspection End
Diagnosis ProcedureINFOID:0000000003772582
INSPECTION PROCEDURE
1.CHECK CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) connector.
3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, re\
pair or replace terminal.
4. Reconnect connectors and then perform the self-diagnosis. Refer to BRC-24, "
CONSULT-III Function
(ABS)".
Is any item indicated on the self-diagnosis display?
YES >> GO TO 2
NO >> Poor connection of connector term inal. Repair or replace connector.
DTCDisplay item Malfunction detected condition Possible cause
C1164 CV1 VDC switch-over solenoid valve (CV1) on the primary
side is open circuit or shorted, or the control line is open
or shorted to the power supply or the ground.
• Harness or connector
• ABS actuator and electric unit (control unit)
C1165 CV2
VDC switch-over solenoid valve (CV2) on the primary
side is open circuit or shorted, or the control line is open
or shorted to the power supply or the ground.
C1166 SV1 VDC switch-over solenoid valve (SV1) on the primary
side is open circuit or shorted, or the control line is open
or shorted to the power supply or the ground.
C1167 SV2 VDC switch-over solenoid valve (SV2) on the primary
side is open circuit or shorted, or the control line is open
or shorted to the power supply or the ground.
Self-diagnosis results
CV1
CV2SV1
SV2
Revision: December 20092009 QX56