2009 HUMMER H3 key

When the System Does Not Seem
To Work Properly
The rear vision camera system may
not work properly or display a
clear image:
In the dark.
When the sun or the beam of
headlamps is shining directly
into the camera lens.
If ice, snow, mud, or anything else
builds up on the camera lens.
Clean the lens, rinse it with water,
and wipe it with a soft cloth.
If the back of the vehicle is in an
accident, the position and
mounting angle of the camera
may change or the camera may
be affected. Be sure to have the
camera and its position and
mounting angle checked at your
dealer/retailer.
If there are extreme temperatures
or extreme temperature changes.The rear vision camera system
display in the rearview mirror may
turn off or not appear as expected
due to a loss of video signal, or
no video signal present during the
reverse cycle. The display will
be blank and the left indicator light
will slowly ash as long as the
vehicle is in R (Reverse) or until the
condition returns to normal.
Pressing and holding
zwhen the
left indicator light is ashing will
turn off the video display along with
the left indicator light.
OnStar®System
OnStar uses several innovative
technologies and live advisors to
provide a wide range of safety,
security, information, and
convenience services. If the airbags
deploy, the system is designed to
make an automatic call to OnStar
Emergency advisors who can
request emergency services be sent
to your location. If the keys are
locked in the vehicle, call OnStar
at 1-888-4-ONSTAR to have a
signal sent to unlock the doors.
OnStar Hands-Free Calling,
including 30 trial minutes good for
60 days, is available on most
vehicles. OnStar Turn-by-Turn
Navigation service, with one trial
route, is available on most vehicles.
Press the OnStar button to have
an OnStar advisor contact Roadside
Service.
Features and Controls 2-39

Luggage Carrier
If the vehicle has this feature, cargo
can be loaded on top of the vehicle.
The luggage carrier consists of
siderails attached to the roof.
The crossrails attach into the
siderails and can be moved back
and forth to accommodate various
cargo sizes.
Notice:Loading cargo on the
luggage carrier that weighs more
than 250 lbs. (113 kg) or hangs
over the rear or sides of the
vehicle may damage the vehicle.
Load cargo only on top of the
crossrails and tie the cargo down
to the crossrail support cargo
tie-down loops, making sure
to fasten it securely
Do not exceed the maximum vehicle
capacity when loading your vehicle.
For more information on vehicle
capacity and loading, seeLoading
the Vehicle on page 4-35.Adjusting the Crossrails
To adjust the crossrails to t a load:
1. Turn the crossrail key
counterclockwise to unlock the
crossrail end cap.
2. Remove the end cap.
3. Pull the lever labeled “PULL”
from left to right to loosen the
crossrail.
4. Repeat Steps 1 through 3 to the
opposite end of the crossrail.5. Once both sides of the crossrail
are loose, adjust the crossrail to
the desired position.
6. Push the lever labeled “PULL”
from right to left to lock the
crossrail in place.
7. Reinstall the end cap and turn
the crossrail key to lock the
crossrail.
8. Repeat Steps 5 through 7 to the
opposite end of the crossrail.
Stop Tabs
If the vehicle has a sunroof, it has a
crossrail stop tab in the siderail.
This tab prevents the crossrail from
being moved past the opening of
the sunroof and cargo from
being loaded too far forward.
The vehicle may have cargo tie
downs. Once the cargo is loaded
onto the crossrails, use the cargo tie
downs to secure it. Do not load
cargo directly on the roof of the
vehicle. SeeCargo Tie Downs on
page 2-49for more information.
2-48 Features and Controls

Headlamps on Reminder
A headlamp reminder chime will
sound if the following conditions
are met:
The driver door is open.
Parking lamps or headlamps are
manually turned on.
The key is either not in the
ignition switch, or it is in the
LOCK/OFF position of the ignition
switch.
The headlamp reminder cannot be
turned off if the conditions listed
above are met.
In the automatic mode, the
headlamps turn off once the ignition
is in ACC/ACCESSORY.
Daytime Running
Lamps (DRL)
Daytime Running Lamps (DRL) can
make it easier for others to see
the front of your vehicle during the
day. Fully functional daytime
running lamps are required on all
vehicles rst sold in Canada.
The DRL system will come on when
the following conditions are met:
The ignition is on.
The exterior lamps control is
in AUTO.
The transmission is not in
P (Park), if the vehicle has
an automatic transmission.
The light sensor determines it is
daytime.When the DRL are on, no other
lamps are on. The instrument panel
will not be lit up either. For
vehicles rst sold in Canada, if
parking lamps are manually turned
on, DRL will stay on.
When it begins to get dark, the
automatic headlamp system will
switch from DRL to the headlamps.
The regular headlamp system
should be turned on when needed.
To turn off the DRL, seeExterior
Lamps on page 3-11.
Vehicles rst sold in Canada cannot
turn off DRL unless certain
conditions are met. SeeExterior
Lamps on page 3-11.
Instrument Panel 3-13

The instrument panel lights, cluster,
and radio display do not dim to
complete darkness. Turn the
thumbwheel all the way up to turn
the dome lamps on.
Dome Lamp
The dome lamps are located in the
front area of the vehicle. There
is also a dome lamp in the cargo
area of the H3 model only.
Turn the thumbwheel, located next
to the exterior lamps control, all
the way up to turn the dome
and footwell lamps on. In this
position, the lamps remain on
whether a door is opened or closed.
The dome lamp in the cargo area
automatically turns off when:
The shift lever is shifted out of
P (Park) (automatic
transmissions).
The parking brake is released
(manual transmissions).
Dome Lamp Override
E
(Dome Lamp Override):You
can use the dome override
button, located below the exterior
lamps control, to set the dome
and footwell lamps to come
on automatically when a door is
opened, or to remain off. To turn the
lamps off, press the
Ebutton in.
With the button in this position,
the dome lamps will remain off when
the doors are open. To return the
lamps to automatic operation, press
Eagain and return it to the out
position. With the button in this
position, the dome lamps will come
on when a door is opened.
Exit Lighting
The interior lamps will come on
when the key is removed from the
ignition. The lamps will not come on
if the dome override button is
pressed in.
Reading Lamps
The reading lamps are located in
the overhead console.
Press the button located next to
each lamp to turn them on or off.
These lamps will not come on
with the dome lamps.
3-16 Instrument Panel

Rear Window Defogger
The rear window defogger uses a
warming grid to remove fog or
frost from the rear window when the
key is in the ignition and turned
to ON/RUN.
=(Rear Defogger):Press to turn
the rear window defogger on or
off. After the button is rst pressed
the rear window defogger stays
on for about 15 minutes. If turned on
again, the defogger only runs for
about seven and one-half minutes.
Notice:Do not use anything
sharp on the inside of the rear
window. If you do, you could cut
or damage the warming grid, and
the repairs would not be covered
by the vehicle warranty. Do not
attach a temporary vehicle
license, tape, a decal or anything
similar to the defogger grid.
Outlet Adjustment
Use the air outlets located in the
center and on the side of the
instrument panel to direct the
airow.
This vehicle has air outlets that
allow you to adjust the direction and
amount of airow inside the
vehicle. Move the louvers up or
down to change the direction of the
airow. Use the thumbwheel
under the outlets to change the
direction of the airow from left
to right.Operation TipsUse the recirculation mode for
maximum air conditioning
performance.
Clear away any ice, snow or
leaves from the air inlets at
the base of the windshield that
may block the ow of air into the
vehicle.
Use of non-GM approved hood
deectors may adversely affect
the performance of the system.
Keep the path under the
front seats clear of objects to help
circulate the air inside of the
vehicle more effectively.
Instrument Panel 3-21

If, after several seconds, both status
indicator lights remain on, or if
there are no lights at all, there may
be a problem with the lights or
the passenger sensing system. See
your dealer/retailer for service.
{CAUTION
If the airbag readiness light ever
comes on and stays on, it means
that something may be wrong with
the airbag system. To help avoid
injury to yourself or others, have
the vehicle serviced right away.
SeeAirbag Readiness Light on
page 3-25for more information,
including important safety
information.
Charging System Light
This light comes on briey when the
ignition key is turned, but the
engine is not running, as a check to
show it is working.
It should go out once the engine
starts. If it stays on, or comes
on while driving, there could be a
problem with the charging system. A
charging system message in the
Driver Information Center (DIC) may
also appear. SeeDIC Warnings
and Messages on page 3-37
for more information. This light could
indicate that there are problems
with a generator drive belt, or that
there is an electrical problem.
Have it checked right away. If the
vehicle must be driven a short
distance with the light on, turn off all
the accessories, such as the
radio and air conditioner.
Up-Shift Light
The vehicle may have an up-shift
light.
When this light comes on, shift to
the next higher gear if weather,
road, and traffic conditions allow.
SeeManual Transmission Operation
on page 2-22for more information.
Brake System Warning
Light
The vehicle’s hydraulic brake
system is divided into two parts. If
one part is not working, the
other part can still work and stop
the vehicle. For good braking
though, both parts need to be
working well.
Instrument Panel 3-27

If the warning light comes on, there
could be a brake problem. Have
the brake system inspected
right away.
This light comes on briey when the
ignition key is turned to ON/RUN.
If it does not, have it xed so it
will be ready to warn if there is a
problem.
When the ignition is on, the brake
system warning light comes on
when the parking brake is set. See
Parking Brake on page 2-28for
more information. The light stays on
if the parking brake does not
release fully. If it stays on after the
parking brake is fully released, it
means there is a brake problem.If the light comes on while driving,
pull off the road and stop. The brake
pedal might be harder to push, or
it might go closer to the oor. It can
take longer to stop. If the light is
still on, have the vehicle towed for
service. SeeTowing Your Vehicle
on page 4-40.
{CAUTION
The brake system might not be
working properly if the brake
system warning light is on. Driving
with the brake system warning
light on can lead to a crash. If the
light is still on after the vehicle
has been pulled off the road and
carefully stopped, have the
vehicle towed for service.
Antilock Brake System
(ABS) Warning Light
For vehicles with the Antilock Brake
System (ABS), this light comes
on briey when the engine is started.
If it does not, have the vehicle
serviced by your dealer/retailer. If
the system is working normally
the indicator light will then go off.
If the ABS light stays on, turn
the ignition off. If the light comes on
while driving, stop as soon as it
is safely possible and turn the
ignition off. Then start the engine
again to reset the system. If the ABS
light stays on, or comes on again
while driving, the vehicle needs
service. If the regular brake system
warning light is not on, the vehicle
still has brakes, but not antilock
brakes. If the regular brake system
warning light is also on, the
vehicle does not have antilock United States
Canada
3-28 Instrument Panel

the vehicle’s fuel economy might
not be as good, and the engine
might not run as smoothly.
This could lead to costly repairs
that might not be covered by
the vehicle warranty.
Notice:Modications made to
the engine, transmission,
exhaust, intake, or fuel system of
the vehicle or the replacement
of the original tires with other
than those of the same Tire
Performance Criteria (TPC) can
affect the vehicle’s emission
controls and can cause this light
to come on. Modications to
these systems could lead
to costly repairs not covered by
the vehicle warranty. This
could also result in a failure to
pass a required Emission
Inspection/Maintenance test. See
Accessories and Modifications
on page 5-3.This light comes on during a
malfunction in one of two ways:
Light Flashing:A misre condition
has been detected. A misre
increases vehicle emissions and
could damage the emission control
system on the vehicle. Diagnosis
and service might be required.
The following can prevent more
serious damage to the vehicle:
Reduce vehicle speed.
Avoid hard accelerations.
Avoid steep uphill grades.
If towing a trailer, reduce the
amount of cargo being hauled
as soon as it is possible.
If the light continues to ash, when
it is safe to do so, stop the
vehicle. Find a safe place to park
the vehicle. Turn the key off, wait at
least 10 seconds, and restart the
engine. If the light is still ashing,
follow the previous steps and
see your dealer/retailer for service
as soon as possible.Light On Steady:An emission
control system malfunction has been
detected on the vehicle. Diagnosis
and service might be required.
An emission system malfunction
might be corrected by:
Make sure the fuel cap is fully
installed. SeeFilling the Tank
on page 5-7. The diagnostic
system can determine if the fuel
cap has been left off or
improperly installed. A loose or
missing fuel cap allows fuel
to evaporate into the atmosphere.
A few driving trips with the cap
properly installed should turn
the light off.
If the vehicle has been driven
through a deep puddle of
water, the vehicle’s electrical
system might be wet. The
condition is usually corrected
when the electrical system dries
out. A few driving trips should
turn the light off.
Instrument Panel 3-31