2009 HUMMER H3 reset

6(Low Speed):For steady
wiping at low speed, turn the band
away from you to the rst solid
position past the delay settings.
1(High Speed):For high-speed
wiping, turn the band to the
second solid position past the delay
settings.
9(Off):Move the band to off, to
stop the wipers.
Be sure to clear ice and snow from
the wiper blades before using
them. If they are frozen to the
windshield, carefully loosen or thaw
them. If the blades do become
worn or damaged, get new blades
or blade inserts.
Windshield wipers work in all power
modes, except when the ignition
is set to LOCK/OFF. After the
engine is turned off, wipers will work
in Retained Accessory Power
(RAP) mode until a door is opened.
SeeRetained Accessory Power
(RAP) on page 2-17.
Windshield Washer
L
(Washer Fluid):This feature is
located on the paddle marked
with
Lat the top of the
multifunction lever. Push the paddle
to spray washer uid on the
windshield. The wipers will clear the
window and then either stop or
return to the preset speed.
{CAUTION
In freezing weather, do not use
your washer until the windshield is
warmed. Otherwise the washer
uid can form ice on the
windshield, blocking your vision.
Rear Window
Wiper/Washer
For vehicles with this feature, the
knob is located on the instrument
panel below the climate controls.
Z(Rear Wiper):Turn to 1
for a slower wiping speed or to 2 for
a faster wiping speed.
0 (Off):Turn to 0 for off.
=(Washer Fluid):Press to wash
and wipe the window.
3-8 Instrument Panel

Setting Cruise Control
{CAUTION
If you leave your cruise control on
when you are not using cruise,
you might hit a button and go into
cruise when you do not want to.
You could be startled and even
lose control. Keep the cruise
control switch off until you want to
use cruise control.
1. Move the cruise control switch
to on.
2. Get up to the speed desired.
3. Press
Tat the end of the lever
and release it.
4. Take your foot off the accelerator
pedal.
The cruise symbol on the instrument
panel comes on when the cruise
control is engaged.Resuming a Set Speed
Suppose the cruise control is set at
a desired speed and then you
apply the brake or step on the
clutch. This disengages the cruise
control. But it does not need to
be reset.
Once the vehicle is going about
25 mph (40 km/h) or more, move
the cruise control switch briey
from
RtoS.
The vehicle goes back to the
chosen speed and stays there.
If the switch is held at
resume/accelerate the vehicle will
keep going faster until the switch is
released or the brake is applied.
Do not hold the switch at
resume/accelerate, unless you want
the vehicle to go faster.Increasing Speed While Using
Cruise Control
There are two ways to go to a
higher speed:
Use the accelerator pedal to get
to the higher speed. Press
T
at the end of the lever, then
release the button and the
accelerator pedal. The vehicle
will now cruise at the higher
speed. If the accelerator pedal is
held longer than 60 seconds,
cruise control will turn off.
Move the cruise switch fromRto
S. Hold it there until you get up
to the desired speed, and
then release the switch. To
increase the vehicle speed in
small amounts, move the switch
briey to resume/accelerate.
Each time this is done, the
vehicle goes about 1 mph
(1.6 km/h) faster.
3-10 Instrument Panel

If the warning light comes on, there
could be a brake problem. Have
the brake system inspected
right away.
This light comes on briey when the
ignition key is turned to ON/RUN.
If it does not, have it xed so it
will be ready to warn if there is a
problem.
When the ignition is on, the brake
system warning light comes on
when the parking brake is set. See
Parking Brake on page 2-28for
more information. The light stays on
if the parking brake does not
release fully. If it stays on after the
parking brake is fully released, it
means there is a brake problem.If the light comes on while driving,
pull off the road and stop. The brake
pedal might be harder to push, or
it might go closer to the oor. It can
take longer to stop. If the light is
still on, have the vehicle towed for
service. SeeTowing Your Vehicle
on page 4-40.
{CAUTION
The brake system might not be
working properly if the brake
system warning light is on. Driving
with the brake system warning
light on can lead to a crash. If the
light is still on after the vehicle
has been pulled off the road and
carefully stopped, have the
vehicle towed for service.
Antilock Brake System
(ABS) Warning Light
For vehicles with the Antilock Brake
System (ABS), this light comes
on briey when the engine is started.
If it does not, have the vehicle
serviced by your dealer/retailer. If
the system is working normally
the indicator light will then go off.
If the ABS light stays on, turn
the ignition off. If the light comes on
while driving, stop as soon as it
is safely possible and turn the
ignition off. Then start the engine
again to reset the system. If the ABS
light stays on, or comes on again
while driving, the vehicle needs
service. If the regular brake system
warning light is not on, the vehicle
still has brakes, but not antilock
brakes. If the regular brake system
warning light is also on, the
vehicle does not have antilock United States
Canada
3-28 Instrument Panel

An arrow on the fuel gage indicates
the side of the vehicle the fuel
door is on.
Here are three things that can
happen but do not indicate a
problem with the fuel gage:
At the gas station, the gas pump
shuts off before the gage
reads full.
It takes a little more or less fuel
to ll up than the gage indicated.
For example, the gage may
have indicated the tank was half
full, but it actually took a little
more or less than half the tank’s
capacity to ll the tank.
The gage moves a little when
turning a corner or speeding up.
When the fuel in the fuel tank is low,
a LOW FUEL message displays
on the Driver Information
Center (DIC). SeeDIC Warnings
and Messages on page 3-37
for more information.
Driver Information
Center (DIC)
The Driver Information Center (DIC)
displays information such as the
trip odometer, personalization
features, and warning messages.
The DIC display is located on
the instrument panel cluster.
DIC Operation and
Displays
The Driver Information Center (DIC)
comes on when the ignition is on.
If a problem is detected, a warning
message appears on the display.
Pressing and releasing the trip
odometer reset stem on the
DIC acknowledges some current
warnings or service messages.
Some messages only clear after the
required action has been taken.
The DIC has different modes which
can be accessed by pressing the
trip odometer reset stem on the DIC.
These modes are explained in thefollowing section. The DIC trip
odometer reset stem is located on
the instrument panel cluster
next to the DIC display. To scroll
through the available functions,
press and release the reset stem.
Trip Information
Odometer
The odometer is automatically
displayed on the DIC when you start
the vehicle. The odometer shows the
total distance the vehicle has been
driven in either miles for the United
States or kilometers for Canada.
Trip Odometer
Press and release the reset stem
until TRIP appears on the DIC
display. The trip odometer shows the
current distance traveled since the
last reset of the trip odometer in
either miles for the United States or
kilometers for Canada.
To reset the trip odometer, press
and hold the reset stem until
the display returns to zero.
3-34 Instrument Panel

Engine Oil Life System
With the engine off, turn the key to
ON/RUN and then press the
reset stem until OIL LIFE RESET
appears — alternating between OIL
LIFE and RESET — on the DIC
display. The CHANGE OIL message
alerts you to change the oil on a
schedule consistent with your driving
conditions. Always reset the OIL
LIFE message after an oil change.
To reset the message, see
Engine Oil Life System on
page 5-15.
In addition to the engine oil life
system monitoring the oil life,
additional maintenance is
recommended in the Maintenance
Schedule in this manual. See
Engine Oil on page 5-13and
Scheduled Maintenance on page 6-4
for more information.
Language
This feature allows you to choose
the language in which the DIC
display shows information.To set your choice for this feature:
1. With the engine off, turn the
key to ON/RUN, but do not
start the engine.
2. Close all doors so the DOORS
message does not display in
the DIC.
3. Momentarily press and release
the reset stem until the current
language is displayed: English
(default), Spanish, or French.
4. To select a different language,
press and hold the reset stem
until the next language appears.
5. Repeat Step 4 until the desired
language is displayed. Once the
desired language is shown on
the DIC display, the language
is set.
6. To exit the language selection,
momentarily press and release
the reset stem. All DIC messages
will now display in the language
selected.
Automatic Door Locks
This feature allows you to program
the door locks to a preferred
setting.
To set your choice for this feature:
1. With the engine off, turn the
key to LOCK/OFF. Do not
remove the key from the ignition.
2. Press and hold the power
door lock button until the
DIC display shows the current
door lock mode.
3. To view the next available mode,
press and hold the reset stem
until the mode appears. Release
the reset stem and press and
hold again to view the next mode.
4. Once the desired mode is shown
on the DIC display, briey press
the reset stem to set your
choice. The DIC display then
clears.
Instrument Panel 3-35

The following are the available
modes:
Lock 1 (default):On vehicles with
an automatic transmission, this
mode locks all of the doors when
the vehicle is shifted out of P (Park)
and unlocks all of the doors when
the vehicle is shifted into P (Park).
On vehicles with a manual
transmission, this mode locks all of
the doors when the vehicle speed is
greater than 15 mph (24 km/h) and
unlocks all of the doors when the key
is removed from the ignition.
Lock 2:On vehicles with an
automatic transmission, this mode
locks all of the doors when the
vehicle is shifted out of P (Park) and
unlocks the driver’s door when
the vehicle is shifted into P (Park).
On vehicles with a manual
transmission, this mode locks all of
the doors when the vehicle speed is
greater than 15 mph (24 km/h) and
unlocks the driver’s door when the
key is removed from the ignition.Lock 3:On vehicles with an
automatic transmission, this mode
locks all of the doors when the
vehicle is shifted out of P (Park).
The doors will not automatically
unlock.
On vehicles with a manual
transmission, this mode locks all of
the doors when the vehicle
speed is greater than 15 mph
(24 km/h). The doors will not
automatically unlock.
Remote Keyless Entry (RKE)
Feedback
This feature allows you to program
the Remote Keyless Entry (RKE)
feedback to a preferred setting.
To set your choice for this feature:
1. With the engine off, turn the
key to LOCK/OFF. Do not
remove the key from the ignition.
2. Press and hold the lock and
unlock buttons on the RKE
transmitter at the same time.Hold both buttons until the DIC
display shows the current
RKE feedback mode.
3. To view the next available mode,
press and hold the reset stem
until the mode appears. Release
the reset stem and press and
hold again to view the next mode.
4. Once the desired mode is shown
on the DIC display, briey press
the reset stem to set your choice.
The DIC display then clears.
The following are the available
modes:
RFA 1 (default):This mode ashes
the parking lamps when you
press the lock or unlock buttons on
the RKE transmitter.
RFA 2:This mode ashes the
parking lamps and sounds the horn
when you press the lock button
on the RKE transmitter. This mode
also ashes the parking lamps
when you press the unlock button
on the RKE transmitter.
3-36 Instrument Panel

RFA 3:This mode ashes the
parking lamps and sounds the horn
when you press the lock or
unlock buttons on the RKE
transmitter.
RFA 4:This mode disables RKE
feedback. There will be no feedback
when you press the lock or unlock
buttons on the RKE transmitter.
DIC Warnings and
Messages
Messages are displayed on the DIC
to notify the driver that the status
of the vehicle has changed and that
some action may be needed by
the driver to correct the condition.
Multiple messages may appear one
after another. The messages are
displayed for several seconds each.
Some messages may not require
immediate action, but you should
press and release the trip odometer
reset stem to acknowledge that
you received the messages and toclear them from the display. Each
message must be acknowledged
individually.
Some messages cannot be cleared
from the DIC display because
they are more urgent. These
messages require action before they
can be cleared. You should take
any messages that appear on
the display seriously and remember
that clearing the messages only
makes the messages disappear, not
correct the problem.
The following are the possible
messages that can be displayed
and some information about them.
AC (Air Conditioning) OFF
This message displays when
the engine coolant temperature is
too high and the air conditioning
in the vehicle needs to be turned off.
SeeEngine Overheating on
page 5-27andClimate Control
System on page 3-19for more
information. This message displays
along with the ENG HOT message.
ABS (Antilock Brake System)
FAULT
This message displays if there is a
problem with the Antilock Brake
System (ABS). Check the ABS as
soon as possible and have the
vehicle serviced by your
dealer/retailer. SeeBrakes on
page 5-30andAntilock Brake
System (ABS) Warning Light on
page 3-28for more information.
Press and release the reset stem to
acknowledge the message and
clear it from the display.
BRAKES
This message displays if there is a
problem with the brakes. Check
the brakes as soon as possible and
have the vehicle serviced by
your dealer/retailer. SeeBrakes on
page 5-30andBrake System
Warning Light on page 3-27for
more information. Press and release
the reset stem to acknowledge
the message and clear it from the
display.
Instrument Panel 3-37

CHANGE OIL
This message displays when the oil
needs to be changed. Check the
oil in the vehicle as soon as possible
and have the vehicle serviced by
your dealer/retailer. SeeEngine Oil
on page 5-13andScheduled
Maintenance on page 6-4for more
information. Press and release
the reset stem to acknowledge the
message and clear it from the
display.
DOORS
This message displays when one or
more of the doors is ajar. Check
all the doors on the vehicle to make
sure they are closed. The message
clears from the display after all
of the doors are closed.
ENG (Engine) HOT
This message displays when the
engine coolant temperature is
hot. Check the engine coolant
temperature gage. SeeEngine
Coolant Temperature Gage
on page 3-29. Have the vehicleserviced by your dealer/retailer as
soon as possible if you suspect
the engine is overheating. See
Engine Overheating on page 5-27
for more information.
FLUID
This message displays if the brake
uid is low. Check the brake
uid as soon as possible and have
the vehicle serviced by your
dealer/retailer. SeeBrakes on
page 5-30for more information.
Press and release the reset stem to
acknowledge the message and
clear it from the display.
FUEL CAP
This message displays if the
vehicle’s fuel cap is either off or
loose. Pull over as soon as possible
and check to see if the fuel cap is
secure. You may also see the check
engine light on the instrument
panel cluster. If the check engine
light does come on when the
fuel cap was loose, it may take a
few driving trips before the lightturns off. SeeMalfunction Indicator
Lamp on page 3-30for more
information if the light still remains
on. Press and release the reset
stem to acknowledge the message
and clear it from the display.
HSA (Hill Start Assist) ON
This message displays when the Hill
Start Assist is enabled. See
Braking on page 4-3for more
information.
LOW FUEL
This message displays if the level of
fuel in the vehicle is low. Also
check the fuel gage. SeeFuel Gage
on page 3-33for more information.
Rell the fuel tank as soon as
possible.
LOW TIRE
On vehicles with the Tire Pressure
Monitor System (TPMS), this
message displays if a low tire
pressure is detected in any of the
vehicle’s tires. Press and release the
reset stem to acknowledge the
3-38 Instrument Panel