2009 FIAT PANDA inflation pressure

121KNOW
YOUR VEHICLE
SAFETYCORRECT USE
OF THE CARWARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
SNOW TYRESUse snow tyres of the same size as the normal tyres pro-
vided with the car.
Fiat Dealership will be happy to provide advice concern-
ing the most suitable type of tyres for the customer’s re-
quirements.
For the type of tyre to be used, inflation pressures and the
specifications of snow tyres, follow the instructions given
in paragraph “Wheels” in section “Technical specifica-
tions”.
The winter features of these tyres are reduced consider-
ably when the tread depth is below 4 mm. Replace them
in this case.
Due to snow tyre features, under normal conditions of
use or on long motorway journeys, the performance of
these tyres is much lower than that of standard tyres. Lim-
it performance according to the use for which they were
certified.
IMPORTANT When snow tyres are used with a max.
speed index below the one that can be reached by the
car (increased by 5%), place a notice in the passenger’s
compartment, plainly in the driver’s view which states the
max. permissible speed of the snow tyres (as per EC
Directive).
The max. speed of snow tyres with “Q”
marking is 160 km/h. The Highway Code
speed limits must however be always complied
with.
WARNING
All four tyres should be the same (brand and track) to
ensure greater safety when driving and braking and bet-
ter driveability.
Remember that it is inappropriate to change the rotation
direction of tyres.
111-122 PANDA EN 7-10-2009 15:01 Pagina 121

143KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
At the end of the procedure❒
stow the space-saving wheel D-fig. 122 in the space pro-
vided in the boot;
❒
fit the partially-open jack in its box C by forcing it slight-
ly to prevent it from vibrating when travelling;
❒
put the tools back into their locations;
❒
arrange the container and tools in the spare wheel and
secure the clamping device B;
❒
correctly reposition the boot stiff cover.
IMPORTANT Do not use inner tubes with tubeless tyres.
Check the inflation pressure of the tyres and the space-
saving wheel regularly.
IMPORTANT You will need to change the set of bolts if
you want to change the type of wheels fitted (alloy rims
instead of steel rims, and vice versa).The whole set of fas-
tening bolts must be replaced by another set of suitably
sized bolts and use a special space-saving wheel having dif-
ferent building characteristics.
You should keep the bolts and space-saving wheel in case
you decide to use the original type of wheel later on.
F0Z0607m
fig. 131
QUICK TYRE REPAIR KIT FIX & GO
automaticThe quick tyre repair kit Fix & Go automatic is placed in
the boot; the tool bag fig. 131 is located under the driver’s
seat and it is fastened by means of a Velcro strap.
The kit fig. 132 includes:❒
a bottle A with the sealer and fitted with:
– filling pipe B;
– a sticker C with the writing “max. 80 km/h” to be
placed in a position clearly visible by the driver (on
the dashboard) after repairing the tyre;
135-168 PANDA EN 7-10-2009 14:06 Pagina 143

146KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0697m
fig. 134
F0Z0672m
fig. 135
❒
make sure that the compressor switch D-fig. 135 is in
position 0 (off), start the engine, fit the plug E-fig. 136
in the 12 V-socket in the central tunnel and operate the
compressor turning the switch D-fig. 135 to position I
(on). Inflate the tyre at the pressure value specified in
paragraph “Inflation pressure” in chapter “Technical
specifications”.
For a more accurate reading, check pressure gauge
F-fig. 135 with the compressor off;
❒
if after five minutes it is still impossible to reach at least
1.5 bar, disengage the compressor from the valve and
current socket, then move the car forth for approx. ten
metres in order to distribute the sealing fluid inside
the tyre evenly, then repeat the inflation operation;
INFLATING PROCEDURE
Replace the bottle containing out of date
sealant fluid. Dispose of the bottle and the
sealant liquid properly. Dispose according
to the national and local regulations in force.Put on the protection gloves provided to-
gether with quick tyre repair kit.
WARNING
❒
Ensure that the handbrake is engaged. Remove the tyre
valve cap, extract the flexible filler tube A-fig. 134 and
fasten the ring B onto the tyre valve;
135-168 PANDA EN 7-10-2009 14:07 Pagina 146

147KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0673m
fig. 136
F0Z0698m
fig. 137
❒
if after this operation it is still not possible to reach at
least 1.8 bar after five minutes, do not start driving since
the tyre is excessively damaged and the fast tyre re-
pair kit cannot guarantee suitable sealing. Contact
a Fiat Dealership;
❒
if the tyre reaches the pressure specified in “Inflation
pressure” paragraph in the “Technical Specifications”
chapter, start driving immediately;
Apply the adhesive label in a position
clearly visible by the driver as a reminder
that the tyre has been treated with the quick re-
pair kit. Drive carefully, particularly on bends. Do
not exceed 80 km/h. Do not accelerate and brake
suddenly.
WARNING
❒
after driving for about 10 minutes stop and check the
tyre pressure again; remember to engage the handbrake;
If the pressure falls below 1.8 bar, do not
drive any further: the quick tyre repair kit
Fix & Go automatic cannot guarantee proper hold
because the tyre is too much damaged. Contact
a Fiat Dealership.
WARNING
❒
if at least 1.8 bar pressure is read, restore proper pres-
sure (with engine running and handbrake on) and
restart;
❒
drive with the utmost care to the nearest Fiat Dealer-
ship.
135-168 PANDA EN 7-10-2009 14:07 Pagina 147

183KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCETECHNICAL
SPECIFICATIONS
INDEX
F0Z0112m
fig. 185
WHEELS AND TYRESCheck the pressure of each tyre, including the space-saver
wheel, approximately every two weeks and before long
journeys: the pressure should be checked with the tyre
rested and cold.
While driving the car, the pressure increases under stan-
dard conditions: for the correct tyre inflation pressure, see
“Wheels” in “Technical specifications” chapter.
Incorrect pressure causes abnormal tyre wear fig. 185:
A standard pressure: tread evenly worn.
B low pressure: tread particularly worn at the edges.
C high pressure: tread particularly worn in the centre.
❒
the ceiling lights must be off. The car is however pro-
vided with an automatic system for switching-off inter-
nal lights;
❒
do not keep accessories (e.g. sound system, hazard
warning lights, etc...) switched on for a long time when
the engine is not running;
❒
before performing any operation on the electric system,
disconnect the battery negative cable;
❒
battery terminals shall always be perfectly tightened.
IMPORTANT If the charge level remains for a long time
under 50%, the battery is damaged by sulphation, reduc-
ing its capacity and starting attitude.
The battery will also be more at risk of freezing (e.g. al-
ready at −10 °C). Refer to the paragraph “Car inactivity”
in “Starting and driving” if the car is left parked for a long
time.
If after buying the car, you want to install electric acces-
sories which require permanent electric supply (alarm, etc.)
or accessories influencing the electrical supply require-
ments, contact Fiat Dealership whose skilled personnel, in
addition to suggesting the most suitable devices included
in Lineaccessori Fiat, will evaluate the overall electric ab-
sorption, checking whether the car’s electric system is ca-
pable of withstanding the load required, or whether it
should be integrated with a more powerful battery.
Since these devices continue absorbing energy even when
the ignition key is off, they gradually run down the battery.
169-190 PANDA EN 7-10-2009 14:15 Pagina 183

184KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
❒
to allow even wear between the front and rear tyres,
it is advisable to change them over every 10–15 thou-
sand kilometres, keeping them on the same side of the
car so as not to reverse the direction of rotation. The tyres must be replaced when the tread is less than
1.6 mm thick. In all cases, follow the laws in force in the
country where you are driving.
IMPORTANT NOTES
❒
Avoid braking suddenly, burning starts and violent
knocks against curbs, potholes or other obstacles if pos-
sible. Driving for long stretches over bumpy roads can
damage the tyres;
❒
check the tyres regularly for cuts on the sides, swelling
or irregular tread wear. Contact a Fiat Dealership if re-
quired;
❒
avoid overloading the car when travelling: this may cause
serious damage to the wheels and tyres;
❒
if a tyre is punctured, stop the vehicle immediately
and change it to avoid damage to the tyre, the rim, the
suspensions and the steering system;
❒
a tyre will age even if it is not used much. Cracks in
the tread and on the sidewalls are a sign of ageing. Have
the tyres checked by skilled personnel if they have been
fitted for longer than six years. Remember to check
also the space-saver wheel very carefully;
❒
in case of replacement, always fit new tyres, avoiding
those with an unknown origin;
❒
if a tyre is replaced, also change the inflation valve;
Remember that the road holding qualities
of your car also depend on the correct in-
flation pressure of the tyres.
WARNING
If the pressure is too low the tyre will
get overheated, with the risk of serious
damage.
WARNING
Avoid moving the tyres from the right side
of the car to the left side and vice versa.
WARNING
Never submit alloy rims to repainting
treatments requiring to use temperatures
exceeding 150 °C. The mechanical properties of
the wheels could be impaired.
WARNING
169-190 PANDA EN 7-10-2009 14:15 Pagina 184

5,00 B × 13 H2
(steel)
5J × 14 H2
(alloy)
165/65 R14 79T
155/80 R13 79T
199KNOW
YOUR VEHICLE
SAFETY
CORRECT USE OF THE
CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCETECHNICAL
SPECIFICATIONSINDEX
4,50 B 13 H
S135/80 B13 82M
135/80 R13 82P
155/80 R13 79T
165/65 R14 79T
155/80 R13 79T M+S
165/65 R14 79T M+S Version Rims Tyres Tyres Tyre Space-saving wheel
standard snow type optional Rim Tyre
Actual
Active
Dynamic
Emotion
2.0
2.0
2.2
2.2
2.0
2.0
2.2
2.2
2.3
2.3
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
1.8
1.8
1.8
1.8
1.8
1.8
155/80 R 13 79T
165/65 R 14 79T
155/80 R 13 79T
165/65 R 14 79T
155/80 R 13 79T M+S
165/65 R 14 79T M+S2.8
2.8
COLD TYRE INFLATION PRESSURE (bar)
When the tyres are warm, the inflation pressure should be +0.3 bar in relation to the recommended figure.
However, recheck that the value is correct with the tyre cold.Versions Tyres Medium load Full load Space-saving wheel
Front Rear Front Rear
Petrol
MultijetSnow tyres
191-214 PANDA EN 7-10-2009 14:17 Pagina 199

216KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONSINDEX
– interior ..................................... 158
Bulb types ...................................... 150
Bulbs
– bulb types ................................ 150
– generals instructions for
replacement ............................ 149Car inactivity ............................... 122
Car maintenance..................... 169
Car speed indicator
(speedometer) ........................... 14
Car washing
– engine compartment ............ 189
– exterior ................................... 189
– interior ..................................... 190
Carrying children ......................... 98
Ceiling light switching-on/off ..... 68
Central locking ............................. 61
Cigar lighter .................................. 55
Climate control system .............. 43
Climate control system
controls .................................. 41-44
Climate control system vents ... 41
Clock adjustment ................... 16-18Clock
– adjustment ........................... 16-18
Clutch
– technical specifications ......... 195
CO
2emissions ............................. 207
CODE card ................................... 6
Control buttons ........................... 53
Controls (pushbuttons) ............. 53
Correct use of the car.......... 111
Current sockets ........................... 58
Changing a wheel ......................... 137
– general information
and warnings ........................... 137
– tyre and wheel types ............ 199
– tyre inflation pressure .......... 199
Child lock ...................................... 62
Child seats ..................................... 103
– fitness for child seat use ...... 101
– preparation for child seats .. 103
Children (carrying in safety) ..... 98
– preparation for Isofix seat
mounting ................................. 103
Dashboard .................................... 3Defrosting-demisting
– rear window ........................... 40
– windscreen and front side
windows ........................... 39-42-46
Demisting-defrosting
– door mirrors .......................... 36
– rear window ........................... 40
– windscreen and side
front windows ............... 39-42-46
Diesel particulate filter (DPF) ... 90
Digital display ................................ 16
– control buttons ...................... 16
– standard screen ..................... 16
– warning light test .................... 17
Dipped headlights (lights)
– bulb replacement ................... 153
– switching-on ........................... 48
Dipped headlights
– bulb replacement ................... 153
– switching on ............................ 48
Direction indicator
– front bulb replacement ........ 154
– rear bulb replacement .......... 155
– switching on ............................ 49
215-224 PANDA EN 7-10-2009 15:09 Pagina 216