2009 CHERY TIGGO brake sensor

Downloaded from www.Manualslib.com manuals search engine P0506 - Idle Control System RPM Lower Than Expected
•Self-diagnosis detection logic.
DTC NO. DTC DEFINITION DTC DETECTION
CONDITION DTC SET
CONDITION POSSIBLE CAUSE
P0506 Idle control system
RPM lower than expected •
Engine is running.
• With the engine
idling in drive, the
brake applied,
engine run time
below a calibrated
minimum value, and
no VSS, MAF/MAP,
ECT, TPS, ETC,
Crankshaft Position
sensor, fuel system,
or injector DTCs
present. ECM detected that
the idle speed is less than the
acceptable range. •
Electronic throttle
control actuator
• Intake air leak
• ECM
DTC Confirmation Procedure:
Before performing the following procedure, confirm that battery voltage is more than 12 V.
• Turn ignition switch off.
• Connect the X-431 scan tool to the Data Link Connector (DLC) - use the most current software available.
• Turn ignition switch on.
• With the scan tool, record and erase stored DTCs in the ECM.
• Start engine and warm it up to the normal operating temperature then select view DTC.
• If DTC is detected, go to Diagnostic Procedure - Step 1.
• If the DTC is not detected, the DTC condition is intermittent (See Diagnosis & Testing Diagnostic Help in Sec-
tion 03 Electronic Engine Controls).
NOTE :
If DTC P0506 is displayed with other DTCs, perform this diagnostic procedure before other DTCs.
NOTE :
While performing electrical diagnosis & testing, always refer to the electrical schematics for specific circuit
and component information.
DIAGNOSIS & TESTING
03
03–191Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine GENERAL INFORMATION
Description
The Engine Control Module (ECM) utilizes integrated circuitry and information carried on the Controller Area Network
(CAN) data bus along with many hard wired inputs to monitor many sensors and switches inputs throughout the
vehicle. In response to those inputs, the internal circuitry and programming of the ECM allow it to control and inte-
grate many electronic functions and features of the vehicle through both hard wired outputs and the transmission of
electronic message outputs to other electronic modules in the vehicle over the CAN data bus.
The following are the input and output components monitored by the ECM. The monitored functions include compo-
nents from the engine, ignition, transaxle, air conditioning, or any other ECM supported subsystem.
ECM Inputs
•Brake Switch Sensor
• A/C Pressure Switch
• Camshaft Position (CMP) Sensor
• Crankshaft Position (CKP) Sensor
• Engine Coolant Temperature (ECT) Sensor
• Intake Air Temperature (IAT) Sensor
• Air Flow Sensor
• Throttle Position Sensor (integral with Electronic Throttle Control Actuator)
• Power Steering Switch
• Accelerator Pedal Position (APP) Sensor
• Knock Sensor
• Oxygen Sensor (Upstream & Downstream)
• Clutch Pedal Switch (manual transaxle only)
ECM Outputs
• Canister Control Valve
• Fuel Injectors
• Fuel Pump Relay
• Electronic Throttle Control Actuator
• Ignition Coil
• A/C Compressor
• Cooling Fan
• Oxygen Sensor heating coil (Upstream & Downstream)
Operation
The ECM monitors components and circuits and tests them in various ways depending on the hardware, function,
and type of signal. For example, analog inputs such as throttle position or engine coolant temperature are typically
checked for opens, shorts and out-of-range values. This type of monitoring is carried out continuously. Some digital
inputs like vehicle speed or crankshaft position rely on rationality checks - checking to see if the input value makes
sense at the current engine operating conditions. These types of tests may require monitoring several components
and can only be carried out under appropriate test conditions.
The ECM is a pre-programmed, microprocessor-based digital computer. It regulates ignition timing, air-fuel ratio,
emission control devices, charging system, certain transmission features, speed control, air conditioning compressor
clutch engagement and idle speed. The ECM can adapt its programming to meet changing operating conditions.
03
03–229Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine ECM Connector Pin-Out Table
ECM PIN-OUT TABLE
PINCIRCUIT IDENTIFICATION PINCIRCUIT IDENTIFICATION
1 (With EOBD)
42Intake Air Temperature Sensor
Upstream Oxygen Sensor Heater (Without
EOBD)
2 Ignition Coil 2 43-
3 GND (Ignition) 44Switched Supply Voltage
4 (With EOBD)
45Switched Supply Voltage
Downstream Oxygen Sensor Heater
(Without EOBD)
5 Ignition Coil 1 46Canister Control Valve
6 Injector 2 47Injector 4
7 Injector 3 48Upstream Oxygen Sensor Heater (With
EOBD)
(Without EOBD)
8 Engine Speed Output 49-
9 Coolant Temperature Output 50Fan Relay Control
10 Fuel Consumption Output 51GND (Signal)
11 EPC Lamp 52-
12 Continuous Supply Voltage 53GND (Signal)
13 Ignition Switch 54 Electronic Throttle Control Actuator
14 EMS Relay (Main Relay) 55Downstream Oxygen Sensor
15 Crankshaft Position Sensor 56-
16 Accelerator Position Sensor 57-
17 Sensor (GND) 58Brake Switch
18 Upstream Oxygen Sensor 59-
19 Knock Sensor 1 60A/C Middle Pressure Switch
20 Knock Sensor 2 61GND (Power)
21 Brake Switch 62CAN-H
22 -63Switched Supply Voltage
23 Accelerator Sensor 64 Electronic Throttle Control Actuator
24 -65 Electronic Throttle Control Actuator
25 -66 Electronic Throttle Control Actuator
26 -67 Electronic Throttle Control Actuator
27 Injector 1 68Fan Relay Control 2
28 Downstream Oxygen Sensor Heater (With
EOBD) 69Air Compressor Relay
(Without EOBD)
29 -70Fuel Pump Relay
30 -71Diagnostic Link K
31 MIL Lamp 72-
32 Regulated Sensor Supply 3 73Regulated Sensor Supply 2
33 Regulated Sensor Supply 1 74-
34 Crankshaft Position Sensor 75A/C Stand By
GENERAL INFORMATION
03
03–245Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine DTCDTC DEFINITION
P0537 A/C Evaporator Temperature Sensor Circuit Low
P0538 A/C Evaporator Temperature Sensor Circuit High
P0560 System Voltage Malfunction
P0562 System Voltage Low Voltage
P0563 System Voltage High Voltage
P0571 Brake SwitchACircuit
P0601 Internal Control Module EEPROM Error
P0602 Control Module Programming Error
P0604 Internal Control Module Random Access Memory (RAM) Error
P0605 Internal Control Module ROM Test Error
P0606 ECM Processor
P0627 Fuel PumpAControl Circuit Open
P0628 Fuel PumpAControl Circuit Low
P0629 Fuel PumpAControl Circuit High
P0645 A/C Clutch Relay Circuit
P0646 A/C Clutch Relay Control Circuit Low
P0647 A/C Clutch Relay Control Circuit High
P0650 Malfunction Indicator Lamp Control Circuit
P0688 EMC/ECM Power Relay Sense Circuit Open
P0691 Cooling Fan 1 Control Circuit Low
P0692 Cooling Fan 1 Control Circuit High
P0693 Cooling Fan 2 Control Circuit Low
P0694 Cooling Fan 2 Control Circuit High
P0700 Transmission Control System Malfunction
P0704 Clutch Switch Input Circuit
P1297 Manufacturer Controlled Computer And Auxiliary Outputs
P1336 Engine Torque Control Adaptation at Limit
P1545 Throttle Position Control Malfunction
P1558 Throttle Actuator Electrical Malfunction
P1559 Idle Speed Control Throttle Position Adaptation Malfunction
P1564 Idle Speed Control Throttle Position Low Voltage during Adaptation
P1565 Idle Speed Control Throttle Position Lower Limit not Attained
P1568 Idle Speed Control Throttle Position Mechanical Malfunction
P1579 Idle Speed Control Throttle Position Adaptation not Started
P1604 Internal Control Module Driver Error
P1610 Manufacture Controlled Computer and Auxiliary Outputs
P1611 Manufacture Controlled Computer and Auxiliary Outputs
P1612 Manufacture Controlled Computer and Auxiliary Outputs
P1613 Manufacture Controlled Computer and Auxiliary Outputs
P1614 Manufacture Controlled Computer and Auxiliary Outputs
P1651 Manufacture Controlled Computer and Auxiliary Outputs
P2106 Throttle Actuator Control System Forced Limited Power
P2122 Throttle/Pedal Position Sensor/Switch D Circuit Low Input
DIAGNOSIS & TESTING
03–252Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine DTCDTC DEFINITION
P2123 Throttle/Pedal Position Sensor/Switch D Circuit High Input
P2127 Throttle/Pedal Position Sensor/Switch E Circuit Low Input
P2128 Throttle/Pedal Position Sensor/Switch E Circuit High Input
P2138 Accelerator Pedal Position Sensor Signal Correlation Error
P2177 System Too Lean off Idle
P2178 System Too Rich off Idle
P2187 System Too Lean at Idle
P2188 System Too Rich at Idle
P2195 O
2Sensor Signal Stuck Lean; Bank 1 Sensor 1
P2196 O
2Sensor Signal Stuck Rich; Bank 1 Sensor 1
P2270 O
2Sensor Signal Stuck Lean; Bank 1 Sensor 2
P2271 O
2Sensor Signal Stuck Rich; Bank 1 Sensor 2
U0001 High Speed CAN Defective
U0101 Lost Communication with ECM
U0104 Lost Communication with Cruise Control Module
U0121 Lost Communication with Anti-Lock Brake System (ABS) Control Module
U0155 Lost Communication with Instrument Panel Cluster Control Module
U0415 Invalid Data Received from ABS Control Module
DIAGNOSIS & TESTING
03
03–253Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine P0506 - Idle Control System RPM Lower Than Expected
On Board Diagnostic Logic
•Self-diagnosis detection logic.
• If DTC P0506 is displayed with other DTC, first perform the trouble diagnosis for the other DTC.
DTC NO. DTC DEFINITION DTC DETECTION
CONDITION DTC SET
CONDITION POSSIBLE CAUSE
P0506 Idle control system
RPM lower than expected •
Engine is running
• With the engine
idling in drive, the
brake applied,
engine run time
below a calibrated
minimum value, and
no VSS, MAF/MAP,
ECT, TPS, ETC,
Crankshaft Position
sensor, fuel system,
or injector DTCs
present. ECM detected that
the idle speed is less than the
acceptable range. •
Electronic throttle
control actuator
• Intake air leak
• ECM
DTC Confirmation Procedure:
Before performing the following procedure, confirm that battery voltage is more than 12 V.
• Turn ignition switch off.
• Connect the X-431 scan tool to the Data Link Connector (DLC) - use the most current software available.
• Turn ignition switch on.
• With the scan tool, record and erase stored DTCs in the ECM.
• Start engine and warm it up to the normal operating temperature then select view DTC.
• If DTC is detected, go to Diagnostic Procedure - Step 1.
• If the DTC is not detected, the DTC condition is intermittent (See Diagnosis & Testing Diagnostic Help in Sec-
tion 03 Electronic Engine Controls).
NOTE :
While performing electrical diagnosis & testing, always refer to the electrical schematics for specific circuit
and component information.
DIAGNOSIS & TESTING
03–394Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine GENERAL INFORMATION
Description
The Engine Control Module (ECM) consists of a microcomputer and connectors for signal input and output and for
power supply. The ECM controls the engine.
The following are the input and output components monitored by the ECM. The monitored functions include compo-
nents from the engine, ignition, transaxle, air conditioning, or any other ECM supported subsystem.
ECM Inputs
•Brake Switch Sensor
• Camshaft Position (CMP) Sensor
• Crankshaft Position (CKP) Sensor
• Engine Coolant Temperature (ECT) Sensor
• Air Flow Sensor
• Coolant Temperature Sensor (For Instrument Cluster)
• Throttle Position Sensor (Integral with Electronic Throttle Control Actuator)
• Power Steering Switch
• Knock Sensor
• Oxygen Sensor (Upstream & Downstream)
• Clutch Pedal Switch (Manual transmission only)
ECM Outputs
• Canister Control Valve
• Fuel Injectors
• Fuel Pump Relay
• Electronic Throttle Control Actuator
• Ignition Coil
• A/C Compressor
• Cooling Fan
• Oxygen Sensor heating coil (Upstream & Downstream)
Operation
The ECM monitors components and circuits and tests them in various ways depending on the hardware, function,
and type of signal. For example, analog inputs such as throttle position or engine coolant temperature are typically
checked for opens, shorts and out-of-range values. This type of monitoring is carried out continuously. Some digital
inputs like vehicle speed or crankshaft position rely on rationality checks - checking to see if the input value makes
sense at the current engine operating conditions. These types of tests may require monitoring several components
and can only be carried out under appropriate test conditions.
The ECM is a pre-programmed, microprocessor-based digital computer. It regulates ignition timing, air-fuel ratio,
emission control devices, charging system, certain transmission features, speed control, air conditioning compressor
clutch engagement and idle speed. The ECM can adapt its programming to meet changing operating conditions.
03–442Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine DP0 Transaxle Control Module (TCM) Connector Pin-Out Table
TCM Pin-Out Table
PINCIRCUIT IDENTIFICATION PINCIRCUIT IDENTIFICATION
1 + EVS 29-
2 Flow Control Solenoid Valve (+) 30-
3 -31Shift 2
4 -32Shift 3
5 -33Shift 4
6 -34P/N Switch
7 Shift Solenoid Valve 3 35-
8 Shift Solenoid Valve 4 36Sequential (-)
9 Shift Solenoid Valve 2 37Sequential (+)
10 Shift Solenoid Valve 1 38CAN-H
11 Shift Lock 39CAN-L
12 Fluid Cooler Flow Control 40Winter Mode
13 Shift Solenoid Valve 5 41-
14 Shift Solenoid Valve 6 42MFS Switch
15 -43Brake Switch
16 Brake Switch 44-
17 -45Turbine Shaft (+)
18 -46Turbine Shaft (-)
19 CDE EVM PTG 47Secondary Shaft (-)
20 Torque Converter Lock Solenoid Valve
(CDE EVM PRSN) 48
Secondary Shaft (+)
21 -49 -
22 -50 -
23 -51 -
24 Regulated Sensor Supply 52-
25 Sensor (GND) 53Fluid Temperature Sensor (-)
26 Pressure Adjust Solenoid Valve (+EVM) 54 Fluid Temperature Sensor (+)
27 Ignition Switch 55Fluid Pressure Sensor
28 GND 56BATT
GENERAL INFORMATION
08–18Chery Automobile Co., Ltd.