2009 AUDI S3 light

Inst rum ents and w arnin g/indi cat or li ghts
settled at constant idle speed . This indicates that the MIL is working
proper ly .
The warning light il luminates when there is a malfunction in the
engine electronic system . Contact your authorized Audi dealer and
have the malfunction corrected .
For more information~
page 21. •
High beam [D
The ~D warning/indicator light illuminates when the high beams are
on or when you use the head light flasher . For more information
about using the high beams, see~
page 59. •
Turn signals ¢ ¢
The indicator light flashes when you use either turn
signal .
Whenever you use the left¢ or the right¢ turn signal , the indicator
light flashes. When you use the emergency flasher, both indicator lights flash.
If one of the turn signal light bulbs burn out, the turn signal will
flash twice as fast as normal. •
Cruise control
CRUISE (USA models)/ c,)12 (Canada models)
The CRUISE warning/indicator light il lum inates when the cruise
control is activated. •
Airbag system !.!r
This warning/indicator light monitors the airbag and the
tensioner systems .
The !.!r warning light illuminates for a few seconds each time you
switch on the ignition.
If the
! .!r warning light does not go out, or if it illuminates while you
are driving, or if it s tarts to flash, then there is a ma lfunc tion some ­
where in the system . If the light does not illuminate when you
switch on the ignition, this also means there is a malfunction .
& WARNING
If you have a malfunction in the airbag sy stem, cont act y our auth o­
r iz ed A udi dealer immed iate ly. Othe rwise the a irbag or th e belt
te nsio ner ma y not w ork properly in an acci dent . •
Generator 0
This warning/indicator light detects a malfunction in the
generator or in the vehicle's electrical system.
The D warning/indicator light i lluminates when you switch on the
ignition and must go out after the engine has started.
If the
D warning/indicator light illuminates while you are driving,
you should contact your authorized Audi dealer. Since the vehicle battery is discharging, you should switch off any unnecessary elec ­
trical consumers (for example, the air conditioner). •

Safety belts i
This warning/indicator light reminds you to put on your
safety belt.
Th e ,{f. warning/indicator light illuminat es when the ignition is
switched on to remind the driver and (on USA models only) any front
passenger to put on the safety belt. Additionally, an acoustic
warning (gong) will also sound.
For more Information:::::, page 137, "Safety belt warning light-*-"·•
Brake system
BRAKE (USA models) / (CD) (Canada models)
This warning/indicator light illuminates when the brake
fluid level is too low or when there is a malfunction in the
ABS, or when the parking brake is set.
The light illuminates when the ignition is turned on. It goes out after
the engine has been started and the parking brake is fully released.
This indicates that the brake warning light is functioning properly.
If the brake warning light does not light up when the engine is
cranking or the parking brake is applied, there may be a malfunction
in the electrical system. In this case, contact your Audi dealer. If the brake system warning/indicator light flashes, there is a brake
system malfunction.
If the ABS fails, the ABS warning /indicator light (USA
models)/
.J (Canada models) flashes together with the brake system
warning/indicator light:::::,& .
(USA models): If the warning light
BRAKE and the warning light
illuminate together, immediately contact your authorized Audi
dealer or qualified workshop to have all brake pads inspected
=:> page 32.
When the light comes on, an audible warning signal is also given.
Controls and equip ­
ment
Instruments and warning/indicator lights
Parking brake set
The BRAKE or CCi)) (Canada) warning/indicator light illuminates when
the parking brake is set:::::,&.
& WARNING
• USA models : If both the BRAKE warning light and the
warning light come on at the same time, the rear wheels could lock up first under hard braking. Lock-up of the rear wheel brakes
can cause loss of vehicle control and an accident. Have your
vehicle repaired immediately by your authorized Audi dealer or a qualified workshop. Drive slowly and avoid sudden, hard brake
application.
• Canada models: If both the brake warning light CCi)) and the ABS
warning light come on at the same time, the rear wheels could
lock up first under hard braking. Lock-up of the rear wheel brakes
can cause loss of vehicle control and an accident. Have your
vehicle repaired immediately by your authorized Audi dealer or a
qualified workshop. Drive slowly and avoid sudden, hard brake
application
• If the brake warning/ indicator light does not go out after a few
seconds and the parking brake released, or lights up while you are
driving, the fluid level in the brake fluid reservoir is too low. If you
believe that it is safe to do so, proceed immediately at low speed
to the nearest authorized Audi dealer or qualified workshop and have the brake system inspected.
• Always keep in mind that after several brake applications, you
will need greater pressure on the brake pedal to stop your vehicle .
Do not rely on strained brakes to respond with maximum stopping
power in critical situations. You must allow for increased braking
distances. The extra distance used up by fading brakes could lead
to an accident. •
I • •

Instruments and warning/indicator lights
Anti-lock brake system
~ _ (USA models)/ .... (Canada models)
This warning/indicator light monit ors the A BS and the
electronic differenti al lock (EO L).
The ,I<-warning light wi ll come on for a few seconds when the igni ­
tion is switched on. The light will go out after an automatic check
sequence is completed.
There is a malfunction in the ABS when:
• t he war ning/in dicat or li ght does not illuminate when yo u switc h
on the ignition .
• th e warning/indicator l ig ht doe s no t go out after a few sec onds.
• the warning/indicator light illum inates while driving.
Without the electronic assistance of the ABS , the brake system will
still respond and br ake the car. Have the brake system che cked and
restored to its full performance by an authorized Audi dealer a s
soon as possible.
For more information regarding the ABS see
=> page 194 .
Since any malfunction of the ABS also affe cts the ESP, that system's
warning symbol •
=> page 13 will light up along with the A8~/
I':!. (Canada models) warning light.
Unspecific malfunction in the brake system
If bo th the brake warn ing lig ht=> page 15and the wa rn ing l ight
il luminate when the parking brake is released, the likely cause is a
serious m alfun ction in t he brake system beyond an inoperative ABS
=> & .
If an unspec ific defect in the brake sys te m i s indica ted, the e ntire
brake system is likely to be affected and you
must expect degraded
bra ke response and performance.
Since any malfunc tion of the ABS a lso effects the ESP, that system's
warning symbol ~=> page 13 will light up along with the ~1
J
(Canada models) warning light . Malfun
ction in the ele ctronic differential lock
(EDL )
The two syste ms E DL and ABS in te ract. F or th is rea son th e,. ::,
warning li ght/
~ (Canada mode ls) wi ll come on to ind icate a
m alf unctio n in the EDL system =>
page 191 . See your a uthor ized
Aud i dea ler as soon as poss ib le.
& WARNING
• If the / .t (Canada models} warning light does not go out ,
or if it comes on while driving , the ABS system is not working
properly . The veh icle can then be stopped only with the brakes
operating without ABS support . You will not have the protection
ABS provides. Contact your authori zed Audi dealer as soon a s
possible .
• USA models : If both the BRAKE warning light and the
warning light come on at the same time, the rear wheels could
lock up first under hard braking. Rear wheel brake lock -up can
cause loss of veh icle control and an accident . Have your vehicle
repaired immediately by your authorized Audi dealer or a qualified
workshop . Drive slowly and avoid sudden , hard brake application .
• Canada models : If both the brake wa rning light {(j)) and the ABS
warning light come on at the same time , the rear wheels could
lock up first under hard braking. Rear wheel brake lock -up can
cause loss of vehicle control and an accident . Have your vehicle
repaired immediately by your authorized Audi dealer or a qualified
workshop . Drive slowly and avoid sudden, hard brake
application. •
Electro-mechanical power assist / ~
If the i ndicator ligh t illum inates w hile you a re driving, ther e is a
malfunction in the e lectro -mechanica l steering . If the indicator light
is showi ng ....,, , ther e may be a r educ tion i n po w er s teerin g assist. I f
the indicator light is showing @, there may be a total loss of power
s teer ing assis t. The stee ring must be i nspec ted i mme diately by a ._

qualified workshop=> &. With the eng ine not running (e .g . when
t he car is being towed), there is also no power assis t availa ble.
& WARNING
If there is a malfunction , the indi cator light for the electro -mechan ­
ical power assist illuminates . Seek profess ion al assistance . •
Controls and equip ­
ment
Instruments and warning /indi cator lights
I • •

& WARNING (continued)
• Always remember, even if the "snowflake" symbol (ice
warning) does not appear in the display, black ice could be on the
road.
• Always reduce your speed and drive with special care in cold
weather conditions when the chance of encountering icy road
surfaces increases.
[ i] Tips
• If the vehicle is stationary , or if you are driving at a very low
speed, the temperature shown in the display might be slightly
higher than the actual outside temperature. This is caused by the
heat being radiated from the engine.
• On vehicles with S tronic, the reminders do not appear in the
display until you select a gear .
• On vehicles with Audi Navigatio n system*, the displays may
differ from their normal appearance during navigation. •
Applies to ve hicles: with g ears hift indicator and manual transmi ssio n
Gearshift recommendation
This indicator can help conserve fuel.
Controls and equip ­
ment
+55°F
~ 340mi
3~4 Fig . 8 Gearshift
recommendation
Driver information display
In order to become familiar with the gearshift indicator , begin
driving as usual. If the current gear is not the best one for
conserving fuel, the indicator will display the recommended gear .
The display shows the current gear and the recommended gear
=> fig. 8 .
• Upshifting: The display is to the right of the current gear if a
higher gear is recommended.
• Downshifting: The display is to the left of the current gear if a
lower gear is recommended.
Sometimes the indicator will recommend skipping a gear (3.,. 5l.
[ i] Tips
• This indicator should help you conserve fuel. It is not designed
to recommend the correct gear in all driving situations. Only the
driver can decide which gear is correct in certain driving situations
such as when accelerating or driving on hills.
• The display switches off when the clutch pedal is pressed .
• Gear shift recommendation can be deactivated in the driver
information system=>
page 23. •
I • •

Driver informati on displ ay
Service Interval Display
The Service Interval Display is a reminder of the next
service due.
F ig . 9 Sect io n of
i n strum en t cl uster:
Se rv ice in terva l d isplay
The service interval display determines when a service procedure is
needed for your vehicle.
Di sp lay re main ing di sta nce/ tim e
By briefly pulling the knob,@~
page 8, fig. 2, the distance/time
remaining to the next service date is displayed with the ignition on.
The remaining distance/time is not displayed within the first 500 km of a new vehicle or after a service . It is updated every 500 km after
that.
A utom ati c re maini ng d ista nce/ tim e dis play
It operates in two stages:
• Service reminder: At a certa in distance before the next service
event is reached, the message
S ervice in 12 30 mi (2000 km ) 3 0 d ays
or Oil ch ange in 1 230 mi (2000 km ) 15 0 days is displayed when you
switch the ignition on.
• Service event : If the date for service is reached, the message
S ervic e due! appears and the wrench indicator light il luminates. It
is accompanied by an audib le signal. The type of service event is
a lso displayed. T
o r eset the disp lay
The dealership performing the service resets the display when the service has been completed. The display is resets as follows :
• Switch the ignition on .
• Pull the knob@)~
page 8, fig. 2, this message appears: S erv ice
du e!
• Pull the knob until the display Oil chang e in ----- mi (km )--- days
appears in the display . If the reset button is not pulled within 5
seconds, the disp lay reset mode c loses.
[ i ] Tip s
• If a malfunction is present (red symboll, the distance remaining
cannot be called up.
• Do not reset the display between service interva ls . Doing so will
resu lt in an incorrect display .
• If the battery is disconnected, the Service Interva l Display values
are retained.
• On vehicles with the Driver Information System, you can also call
up the service interval display~
page 23.
• If service was not performed at the correct time or the service
interva l display was not reset after service was performed, the addi­
tional mileage driven or the elapsed days will be shown as negative
numbers. •

On-Board Diagnostic system (08D)
On-Board Diagnostics
Fig. 10 location of
Data Link Connecto r
( DL C)
On-Board Diagnostics monitors the components of your emission
control system . Each controlled component in your engine system
has been assigned a code. In case of a malfunction , the component
will be identified and the fault stored as a code in the control
module memory .
The Mil lamp may also illuminate if there is a leak in the on-board
fuel vapor recovery system . If the light illuminates after a refuelling,
pull off the road and stop the vehicle, then check that the fuel filler
cap is properly closed=>
page 227.
In order to make an accurate diagnosis, the stored data can only be
displayed using special diagnostic equipment (generic scan tool for
OBDl.
In order to connect the special diagnostic equipment, push the plug
into the Data Link Connector (DLC). The DLC is located to the right of
the engine hood re lease lever=>
page 21, fig. 10 .
Your authorized Audi dealer or a qualified service station can inter ­
pret the code and perform the necessary repair. •
Contro ls and eq uip­
ment
Driver information display
Malfunction Indicator Lamp (MIL) (USA
models)/ (Canada models)
The Malfunction Indicator Lamp (MIU in the instrument cluster
=> page 17, fig . 5 is part of the On-Board Diagnostic (OBD II) system .
The warning/indicator light illuminates when the ignition is
switched on and goes out after the engine starts and the idle has
stabilized. This indicates that the Mil is working properly .
If the light does not go out after the engine is started, or illuminates
while you are driving, a ma lfunction may exist in the engine system.
If the light starts flashing, the catalytic converter cou ld be damaged.
Continue driving
with reduced power (avoiding sustained high
speeds and/or rapid accelerations) and have the condition
corrected . Contact your authorized Audi dealer.
If the light illuminates , the electronic speed limiter may also be
malfunctioning. For more information=>
page 27, "Electronic speed
limiter".
An improperly closed fuel filler cap may also cause the MIL light to
illuminate => page 221. •
Electronic speed limiter
Your vehicle may be factory equipped with tires that are rated for a
maximum speed of 130 mph (210 km/h) . This is less than the
maximum speed of your vehicle. To reduce the risk of sudden tire
failure and loss of control if the vehicle is operated at excessive
speeds, yo ur vehicle also has an electronic speed limiter. The elec­
tronic speed limiter prevents your vehicle from going faster than the
tire speed rating. For more information
=> page 257, "Speed rating
(letter code)".
If the engine control unit receives faulty vehicle roadspeed signals,
the Malfun cti on Indicator Light (MIU will illuminate . If this
occurs, contact the nearest authori zed Audi dealer for assistance. _.,
Vehicle care I I irechnical data

Driver informati on displ ay
Fig. 1 4 Display : Start
menu
Some functions in your vehicle can be set, activated, and controlled
by
M enu s (e.g. Acoustic park assist*). With these menus you can
also select the information shown in the driver information system,
which operates only with the ignition switched on. Operation is
control led by the
I Reset) button and the rocker switch on the wiper
lever =>
page 23, fig. 13 .
The
S ta rt m enu shows you the different disp lay types :
Set
C he ck
M enu off
Each display type in the Start menu contains a submenu with addi­
tiona l options .
Set
C he ck
M enu off
Clock => page 26
Computer => page26
Speed alarm (speed => page27
warning)
Language (6 languages)
Units (distance, fuel con-
=> page26
sumption, temperature)
Displays (gearshift rec -=> page 19
ommendationl
Lighting* (exterior lights, => page 56
turn signals) => page 59
Wiper (service position) => page 66
Window => page 47
Doors (Auto-lock)
Acoustic park assist*
Service
=> page38
=> page 112
=> page20
Chassis number* => page 298
Engine oil temperature*
Registered keys
=> page 35
All of the messages shown in vehicles without
menu display appear on the display screen.
•