2009.5 Citroen C CROSSER DAG Owner's Manual

II
C O M F O R T
65
Spectacles storage
Press the cover to open it.
To close it, push the cover until it locks.
Upper glove box with air
conditioning
Press button A on the lid to open it.
To close it, push the lid up.
It is fi tted with a ventilation nozzle which
can be closed by means of a dial, dis-
tributing conditioned air at the same
temperature as the vents in the passen-
ger compartment.
In cold weather, it is advisable to close
this vent to conserve the ambient air in-
side the passenger compartment. Lower glove box
This is fi tted with a lock.
To unlock it, turn the key to the left.
To open it, pull the handle
A .
To close it, push the lid up.
To lock it, turn the key to the right.
It is fi tted with a pen holder and a card
holder.
It is lit on opening when the lights stalk
is activated.

II
!
C O M F O R T
66
Upper storage compartment
Pull the right-hand lever to open the
storage compartment lid, which serves
as an armrest.
To close, fold down the lid until it locks. Lower storage compartment
Pull the left-hand lever to open the lid.
To close, fold down the lid until it locks.
12 volt socket (120 W max)
This is operational when the ignition
switch is in the "LOCK", "ON" or "ACC"
position.
Check that the electrical equipment
operates correctly with a voltage of
12 volts and that its electrical power is
120 W maximum.
The prolonged use of electrical
equipment without running the en-
gine may discharge the battery.
Armrest with storage compartments
12 volt socket (120 W max)

II!
C O M F O R T
67
12 volt socket (120 W max) Removable ashtray
This operates when the ignition switch is
in the "LOCK", "ACC" or "ON" position.
Open the cover to gain access to the
socket. Check that the electrical equip-
ment operates with 12 volts and
that its maximum electrical power
is 120 W.
When you use the two sockets at the
same time, ensure that the two items
of equipment together operate with
12 V and that their combined electrical
power is 120 W maximum.
The prolonged use of electrical equip-
ment without running the engine may
discharge the battery.
Pull the cover to open the ashtray.
To empty, remove the ashtray by pulling
it upwards.

II
C O M F O R T
68
Enclosed storage compartment
Pull the storage compartment lid to
open it. Cup holder
There is a cup holder incorporated in
the fascia on the driver's side.
Press on the centre of the cover to extract
the plate.
Pull it fully to use it.
Push it fully to store it.
Two further cup holders are available in
front of the front armrest.

II
C O M F O R T
69
REAR INTERIOR LAYOUT
Rear armrest
Pull the armrest forwards to lower it.
Cup holder
Open the cover A located at the end of
the armrest holding the side with your
hand. Bottle holder
There is a bottle holder in each rear
door.
Grab handle
Pull the handle downwards to lower it.
Coat hook
The rear left grab handle is fi tted with a
coat hook.

II
70
BOOT LAYOUT

1. 12 volt socket (120 W max).

2. Open storage compartment.

3. Right-hand side enclosed storage
compartment.

4. Storage compartment in the fl oor * .

5. Stowing rings.

6. Left-hand side storage
compartment or audio equipment.

7. Load space cover.
* 5-seat version only.

II
!
C O M F O R T
71 * On 5-seat version only.
Raise the boot fl oor to gain access to
this compartment.
Right-hand side enclosed storage
compartment
This storage compartment contains the
tools for changing a wheel. Storage compartment in the fl oor *
12 volt socket (120 W max)
There are four stowing rings in the boot
for securing luggage:
- two rings are located on the boot fl oor,
- two rings are located on the rear side pillars.
This operates when the ignition switch
is in the "ON" or "ACC" position.
Lift the cover to gain access to the
socket.
Check that the electrical equip-
ment operates with 12 volts and
that its maximum electrical pow-
er is 120 W.
The prolonged use of electrical equip-
ment without running the engine may
discharge the battery.
Stowing rings

II
!
C O M F O R T
72
Second installation position.
The load space cover can be secured
in two different positions B , so that the
row 2 seat backs can be tilted.

1. Roll up the load space cover.

2. Move one of the slides C towards
the inside of the vehicle and insert
the tab D in the installation hole to
be used.
Move the opposite slide in the same way.

3. After changing the position, check
that the load space cover is secured
correctly. Removing the load space cover.

1. Roll up the load space cover.

2. Move one of the slides C towards the
inside of the vehicle and raise it.
Release the opposite slide in the same way.
To put the load space cover in place, carry
out the operations in reverse order.
Load space cover
Unroll the load space cover and install it
in the securing groove A .
To store the load space cover, release
it from the securing groove, it rolls up to
its initial position.
Take care not to place heavy
objects on the load space cover
when it is unfolded.
The load space cover can be stored
along the lower tailgate, unless audio
equipment is present.