2009.5 Citroen C CROSSER DAG Owner's Manual

IX
P R A C T I C A L I N F O R M A T I O N
137
After changing a wheel
When using the "space-saving"
spare wheel, do not exceed a speed
of 50 mph (80 km/h).
Have the tightening of the bolts and
the pressure of the spare wheel
checked by a CITROËN dealer with-
out delay.
Have the punctured wheel repaired
and replace it on the vehicle as soon
as possible.
Fitting the wheel List of operations

 Lower the vehicle fully.

 Fold the jack 2 and detach it.
 Lock the anti-theft bolt using the
wheelbrace 1 fi tted with the anti-
theft socket 5 (if your vehicle is
equipped with one).

 Lock the other bolts using the wheel-
brace 1 only.

 Store the tools (refer to the paragraph
"Access to the tools").
Fitting snow tyres
If you equip your vehicle with snow
tyres fi tted on steel wheel rims, it is

imperative that special bolts avail-
able from your CITROËN dealer are
used.

 Put the wheel in place on the hub.

 Screw in the bolts by hand to the
stop.

 Pre-tighten the anti-theft bolt us-
ing the wheelbrace 1 fi tted with the
anti-theft socket 5 (if your vehicle is
equipped with one).

 Pre-tighten the other bolts using the
wheelbrace 1 only.

IX
!
!
P R A C T I C A L I N F O R M A T I O N
138
CHANGING A BULB
Handle the bulbs using a dry
cloth.

Do not clean the headlamps using
a dry or abrasive cloth, or using
detergent or solvent products, use
a sponge and soapy water. In some climatic conditions (e.g. low
temperature or humidity), the pres-
ence of misting on the internal sur-
face of the glass of the headlamps
and rear lamps is normal; it disap-
pears after the lamps have been on
for a few minutes.
Front lights

1. Direction indicators
(PY21W - 21 W).

2. Dipped headlamps (H11 - 55 W)
or xenon bulb (D2S - 35 W).

3. Side lights (W5W - 5 W).

4. Main beam headlamps
(H7 - 55 W).

5. Front fog lamps
(H11 - 55 W). WARNING: RISK OF
ELECTROCUTION
Xenon bulbs must be replaced by a
CITROËN dealer.

IX
P R A C T I C A L I N F O R M A T I O N
139
Changing the direction indicators (1) Coloured bulbs must be replaced
with bulbs of identical specifi cation
and colour.

 Turn the bulb holder A to the left
and remove it.

 Pull the bulb and change it.
To refi t, carry out these operations in
reverse order. Access to the bulbs on the left-hand
side
When you change a bulb on the left-
hand side, remove the relay box fi xing
nut
B and move the relay box towards
the rear. Access to the bulbs on the right-
hand side
When you change a bulb on the right-
hand side:

 Remove the screenwash reservoir
fi xing C and move the reservoir to-
wards the rear.

 Remove the coolant reservoir fi xing
nut D .

 Remove the clip E and raise the reser-
voir moving it towards the front.

IX
140
Changing the side lights (3)

 Unscrew the cover H .

 Disconnect the connector.

 Turn the bulb holder I a quarter of a
turn and remove it.

 Pull the bulb and change it.
To refi t, carry out these operations in
reverse order.

 Unscrew the cover F .

 Disconnect the connector.

 Turn the bulb G to the left and re-
move it.
To refi t, carry out these operations in
reverse order.
Changing the dipped headlamps (2)
Changing the main beam
headlamps (4)

 Unscrew the cover J .

 Disconnect the connector.

 Move aside the spring K to release
the bulb and remove it.
To refi t, carry out these operations in
reverse order.

IX
P R A C T I C A L I N F O R M A T I O N
141
Changing the integrated direction
indicator side repeaters Changing the fog lamps (5)

 Push the repeater A towards the
rear and detach it.

 Unclip the repeater.

 Disconnect the repeater connector
and change the repeater.
To refi t, carry out these operations in
reverse order.
To obtain repeaters, contact a CITROËN
dealer.
 Turn the wheel fully towards the out-
side for easy access to the fl ap A
located in the wheelarch.
 Using a screwdriver, remove the four
clips B located in the wheelarch.

IX
P R A C T I C A L I N F O R M A T I O N
142

 Using a screwdriver, remove the
three clips C located below the
bumper.
 Lift the access fl ap D located in the
wheelarch and slide it downwards.
 Disconnect the connector E .

 Turn the bulb F to the left and re-
move it.
To refi t, carry out these operations in
reverse order.

IX
P R A C T I C A L I N F O R M A T I O N
143
Rear lights

1. Third brake light (diodes).

2. Brake lights/Side lights
(21/5 - W21W - 5 W).

3. Direction indicators
(WY21W - 21 W).

4. Reversing lights (W21W - 21 W).

5. Number plate lights
(W5W - 5 W).

6. Fog lamps (W21W - 21 W). Changing the brake lights/side
lights and direction indicators
These two bulbs are changed from out-
side with the tailgate open:

 Open the tailgate (refer to the "Access"
section),

 Remove the two light fi xing bolts A ,

 Extract the light from outside,

Turn the pin C to the left and remove it.

 Pull the bulb D and change it.
To refi t, carry out these operations in
reverse order.


Turn the pin B to the left and remove it.

 Pull the bulb and change it. When refi tting the light, align the two
pins
E with the openings on the vehicle.
Amber coloured bulbs, such as the
direction indicators, must be replaced
with bulbs of identical specifi cation
and colour.
Changing the third brake light
(diodes)
All work on the diode lights must be car-
ried out by a CITROËN dealer.

IX
144
Changing the reversing lights

 Open the tailgate (refer to the "Access"
section),

 From the inside of the tailgate, in-
sert a screwdriver in the opening on
the cover A to use it as a lever to
open the cover. Changing the number plate lights

 Open the tailgate (refer to the "Access"
section) to gain access to the number
plate lights D ,

 Remove the light unit D while pressing
it to the left.


Turn the pin B to the left and remove it.

 Pull the bulb C and change it.
To refi t, carry out these operations in
reverse order.
 Insert a thin screwdriver in the open-
ing on the lens to press the tab E .

 Remove the lens.

 Pull the bulb and change it.
To refi t, carry out these operations in
reverse order.

 To refi t the light unit, insert the end of
the tab F fi rst, then align the tab G .