2008 TOYOTA 4RUNNER lock

172
The center differential can be locked or
unlocked by pushing the center differential
lock switch.
Use the center differential lock system if
your wheels get stuck in a ditch, or when
you are driving on a slippery or bumpy
surface. When the center differential is
locked, the vehicle stability control system
is automatically turned off and the center
differential lock and VSC OFF" indicator
lights come on because the function that
controls engine performance interferes
with the process of freeing your wheels.
NOTICE
As soon as the center differential lock
switch is turned on, the VSC OFF"
indicator light comes on. After the
wheels are out of the ditch or off the
slippery or bumpy surface, turn the
center differential lock switch off.
Make sure that the center differential
lock indicator light and VSC OFF"
indicator light turn off.
H2" (high speed position, two−wheel
drive): Multi−mode control switch knob at
H2"
Use this for normal driving on dry hard−
surfaced roads. This position gives greater
economy, quietest ride, least wear and
better vehicle control.
H4" (high speed position, four−wheel
drive) and center differential unlocked:
Multi−mode control switch knob at H4",
center differential unlocked
The four−wheel drive indicator light comes
on when the H4" mode is selected.
Use this for greater traction than two−
wheel drive. (When you experience a loss
of power, such as wheel slipping.) This
position provides greater traction than
two−wheel drive.
H4" (high speed position, four−wheel
drive) and center differential locked:
Multi−mode control switch knob at H4",
center differential locked
The four−wheel drive indicator light comes
on when the H4" mode is selected.
Use this for greater traction when you
experience a loss of power, such as
wheel slipping, in the center differential
unlock mode. L4" (low speed position, four−wheel
drive) and center differential unlocked:
Multi−mode control switch knob at L4",
center differential unlocked
The four−wheel drive and 4LO" (low
speed four−wheel drive) indicator lights
come on when the L4" mode is selected.
Use this for maximum power and traction.
Use this for climbing or descending steep
hills, off−road driving, and hard pulling in
sand or mud.
In this mode, the braking feeling that oc-
curs when the wheels are negotiating a
sharp corner is further reduced than in the
L4" (low speed position, four−wheel drive)
and center differential locked mode.
L4" (low speed position, four−wheel
drive) and center differential locked:
Multi−mode control switch knob at L4",
center differential locked
The four−wheel drive and 4LO" (low
speed four−wheel drive) indicator lights
come on when the L4" mode is selected.

173
Use this for maximum power and traction.
Use this for hard pulling in situations the
vehicle cannot negotiate even in the L4"
(low speed position, four−wheel drive) and
center differential unlocked mode. Also,
using this mode when driving down steep
off−road inclines will help contribute to in-
creased vehicle stability.
The indicator light tells when the differen-
tial lock is engaged. Note that the differ-
ential is not still locked as long as the
indicator light remains off.
When the operation is not completed, the
indicator blinks. If the indicator light does
not go off when you push the center
differential lock switch to unlock the cen-
ter differential, drive straight ahead while
accelerating or decelerating, or drive in
reverse.
If the center differential lock system op-
eration is not completed within 5 seconds
while the cruise control system is set,
cancel the cruise control system. To can-
cel the cruise control system, see Cruise
control" on page 203 in Section 1−7.
If the indicator blinks even if doing so,
contact your Toyota dealer as soon as
possible. There may be a trouble in the
center differential lock system.See (c) Shifting procedure" for further in-
structions.
The A.D.D. can be engaged or disen-
gaged by the shifting operations de-
scribed in (c) Shifting procedure".
You should drive in four−wheel drive for
at least 16 km (10 miles) each month.
This will assure that the front drive com-
ponents are lubricated.
(b) A.D.D.
(automatic disconnecting
differential)

174
SHIFTING BETWEEN H2" AND H4"
(UNLOCKED)
To shift from H2" to H4" (unlocked),
reduce the vehicle speed to less than 100
km/h (62 mph) and turn the multi−mode
control switch knob fully clockwise.
If the four−wheel drive indicator light con-
tinues to blink when you operate the mul-
ti−mode control switch knob from the H2"
to the H4" position, this reminds you that
the transfer mode is not securely in H4"
mode. Drive straight ahead while acceler-
ating or decelerating.
If the four−wheel drive indicator and the
center differential lock indicator lights con-
tinue to blink and the buzzer sounds when
you operate the multi−mode control switch
knob from the H2" to the H4" position,
this reminds you that the vehicle speed is
above 100 km/h (62 mph). Reduce the
vehicle speed to less than 100 km/h (62
mph). Operate the switch knob again.To shift from H4" (unlocked) to H2",
turn the multi−mode control switch knob
fully counterclockwise.
This can be done at any speed.
If the four−wheel drive indicator light con-
tinues to blink when you operate the mul-
ti−mode control switch knob from the H4"
to the H2" position, this reminds you that
the transfer mode is not securely in H2"
mode. Drive straight ahead while acceler-
ating or decelerating, or drive forward or
backward in a short distance.
If the indicator light continues to blink
even if doing so, contact your Toyota
dealer as soon as possible. There may be
a trouble in the four−wheel drive system.
CAUTION
Never operate the multi−mode control
switch knob if the wheels are slip-
ping. Stop the slipping or spinning
before operating.
SHIFTING BETWEEN H4" (UNLOCKED)
AND H4" (LOCKED)
To shift between unlock and lock
modes in H4", push the center differen-
tial lock switch.
SHIFTING BETWEEN L4" (UNLOCKED)
AND L4" (LOCKED)
To shift between unlock and lock
modes in L4", push the center differen-
tial lock switch.
SHIFTING BETWEEN H4" AND L4"
To shift from H4" to L4",
bring the
vehicle to a complete stop with the brake
pedal held down with your foot, shift the
automatic transmission selector lever into
N" and push and turn the multi−mode
control switch knob fully clockwise.
To shift from L4" to H4", bring the
vehicle to a complete stop with the brake
pedal held down with your foot, shift the
automatic transmission selector lever into
N" and turn the multi−mode control switch
knob counterclockwise.
(c) Shifting procedure

183
The vehicle stability control system
helps provide integrated control of the
systems such as anti−lock brake sys-
tem, traction control, engine control,
etc. This system automatically controls
the output of the brakes or engine to
help prevent the vehicle from skidding
when cornering on a slippery road sur-
face or operating steering wheel abrupt-
ly.
The vehicle stability control system is acti-
vated when the vehicle speed is more
than 15 km/h (9 mph).
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
begins to move. This means that the sys-
tem is in the self−check mode, but does
not indicate a malfunction.CAUTION
Do not rely excessively on the ve-
hicle stability control system. Even
if the system is operating, it cannot
completely eliminate the possibility
of an accident. Always keep safe
driving in mind, as reckless driving
increases the risk of an accident. If
the slip indicator light blinks, spe-
cial care should be taken while
driving.
Only use tires of specified size. The
size, manufacturer, brand and tread
pattern for all 4 tires should be the
same. If you use the tires other
than specified, or different type or
size, the vehicle stability control
system may not function correctly.
When replacing the tires or wheels,
contact your Toyota dealer. (See
Checking and replacing tires" on
page 443 in Section 7−2.)
CY16073
If the vehicle is going to skid during driv-
ing, the slip indicator light blinks and an
alarm sounds intermittently. Special care
should be taken while driving.
If the brake pedal is depressed while the
vehicle stability control system is active,
the brake pedal will become hard at an
earlier position than usual. However, the
brakes will respond to the pedal force if
depressed further.
The slip indicator light comes on for a few
seconds when the engine switch is turned
to ON". If the indicator light does not
come on when the engine switch is turned
on, contact your Toyota dealer.
Vehicle stability control
system

184
CY16061
Four−wheel drive models only
Pushing the center differential lock
switch automatically turns the vehicle
stability control system off. At this
time, the VSC OFF" indicator comes
on with the center differential lock indi-
cator light.
The VSC OFF" indicator light comes on
for a few seconds when the engine switch
is turned to ON". It will come on again
when you push the center differential lock
switch to turn on the system.In the following cases, contact your Toyota
dealer:
The indicator light does not come on
when the engine switch is turned to
ON".
The indicator light remains on after the
engine switch is turned to ON".
The indicator light comes on when the
system is on while driving.
NOTICE
Make sure that the center differential
lock indicator light goes off before
normal driving.
CY16075
When getting the vehicle out of mud or
newly fallen snow, etc., turn off the
vehicle stability control system. This
system that controls engine perfor-
mance interferes with the process of
freeing rear wheels (two−wheel drive
models) or 4 wheels (four−wheel drive
models).
To turn off: First, push the VSC OFF"
switch to turn off the traction control
system and check that the AUTO LSD"
and slip indicator lights come on. Then,
push and hold the VSC OFF" switch
for 3 seconds or more with the vehicle
stopped.
The VSC OFF" and slip indicator lights
will come on.

219
If this button is pushed while a compact
disc that does not contain text data is
playing, NO TITLE" will appear on the
display.
If the entire disc or track title does not
appear on the display, push and hold the
button until you hear a beep. The rest of
the title will appear.
MP3/WMA player
This button is used to change the display
for the MP3/WMA file that contains text
data.
To change the display, quickly push and
release the TEXT" button while the
MP3/WMA file is playing. The display
changes in the order from the elapsed
time to folder name to file name to album
title to track title to artist name, then back
to the elapsed time.
If this button is pushed while an
MP3/WMA file that does not contain text
data is playing, NO TITLE" will appear on
the display.
If the entire text data is not displayed,
push and hold it until you hear a beep.
The rest of the text data will appear.TUNE·FILE (Tuning and File up/down)
Radio
Turn the knob clockwise to step up the
frequency. Turn the knob counterclockwise
to step down the frequency.
MP3/WMA player
Turn the knob clockwise to file up. Turn
the knob counterclockwise to file down.

228
This XM tuner supports Audio Services"
(Music and Talk) of only XM
 Satellite
Radio and Text Information"∗ 2 linked to
the respective audio services.
∗ 1: Use of satellite radio r equires XM
tuner and service. Contact your Toyota
dealer for details.
∗
2: Text Information includes, Channel
Name, (Artist) Name, (Song) Title and
Category Name.
Compact disc player
This button is used to change the display
for the compact disc that contains text
data.
To change the display, quickly push and
release the TEXT" button while the com-
pact disc is playing. The display changes
in the order from the elapsed time to disc
title to track title, then back to the
elapsed time.
If this button is pushed while a compact
disc that does not contain text data is
playing, NO TITLE" will appear on the
display.
If the entire disc or track title does not
appear on the display, push and hold the
button until you hear a beep. The rest of
the title will appear. MP3/WMA player
This button is used to change the display
for the MP3/WMA file that contains text
data.
To change the display, quickly push and
release the TEXT" button while the
MP3/WMA file is playing. The display
changes in the order from the elapsed
time to folder name to file name to album
title to track title to artist name, then back
to the elapsed time.
If this button is pushed while an
MP3/WMA file that does not contain text
data is playing, NO TITLE" will appear on
the display.
If the entire text data is not displayed,
push and hold it until you hear a beep.
The rest of the text data will appear.
TUNE·FILE (Tuning and File up/down)
Radio
Turn the knob clockwise to step up the
frequency. Turn the knob counterclockwise
to step down the frequency.
XM
 Satellite Radio∗
Turn the TUNE·FILE" knob clockwise to
step up the channel. Turn the knob coun-
terclockwise to step down the channel.
∗: Use of satellite radio r equires XM
tuner and service. Contact your Toyota
dealer for details.
MP3/WMA player
Turn the knob clockwise to file up. Turn
the knob counterclockwise to file down.
TYPE
XM
 Satellite Radio∗
When you push the  " or " side of
the TYPE" button while receiving a XM

channel, the current channel category ap-
pears on the display.
When the channel category appears, push
either  " or  " side of the TYPE" but-
ton to switch to the next or previous cate-
gory.
∗: Use of satellite radio r equires XM
tuner and service. Contact your Toyota
dealer for details.

238
TUNE·FILE (Tuning and File up/down)
Radio
Turn the knob clockwise to step up the
frequency. Turn the knob counterclockwise
to step down the frequency.
XM
 Satellite Radio∗
Turn the TUNE·FILE" knob clockwise to
step up the channel. Turn the knob coun-
terclockwise to step down the channel.
∗: Use of satellite radio r equires XM
tuner and service. Contact your Toyota
dealer for details.
MP3/WMA player
Turn the knob clockwise to file up. Turn
the knob counterclockwise to file down.
TYPE
XM
 Satellite Radio∗
When you push the  " or " side of
the TYPE" button while receiving a XM

channel, the current channel category ap-
pears on the display.
When the channel category appears, push
either  " or  " side of the TYPE" but-
ton to switch to the next or previous cate-
gory.
∗: Use of satellite radio r equires XM
tuner and service. Contact your Toyota
dealer for details.
CY17029
Some parts of the audio system can be
adjusted using the switches on the steer-
ing wheel.
Details of the specific switches, controls,
and features are described below.
1. Volume control switches
2.  " switch
3. MODE" switch 1. Volume control switches
Push the +" side to increase the volume.
The volume continues to increase while
the switch is being pushed.
Push the −" side to decrease the volume.
The volume continues to decrease while
the switch is being pushed. 2.    " switch
Radio
This switch has the following features
To select a preset station:
Quickly push and release the  " or  "
side of the switch. Do this again to select
the next preset station.
To seek a station:
Push and hold the  " or  " side of the
switch until you hear a beep. Do this
again to find the next station. If you push
the switch on either side during the seek
mode, seeking will be cancelled.
To step up or down the frequency, push
and hold the switch even after you hear
a beep. When you release the switch, the
radio will begin seeking up or down for a
station. Do this again to find the next
station.
Audio remote controls
(steering switches)