2008 SMART FORTWO COUPE tire type

Useful features
164
>> Controls.
Sun visorsThe sun visors protect you from sun glare
while driving.1
Sun visor
2
Mounting
Glare through the windshield
>Swing sun visor
1
down.
Glare through a side window
>Swing sun visor
1
down.
>Disengage sun visor1 from mounting
2.
>Pivot sun visor
1 to the side.
Sun screen*
1
The sun screen provides protection from sun
rays and from heat generated by the
panorama roof*.
The sun screen can be adjusted to any desired
position.1
Sun screen
> Opening or closing: Move sun screen
1
forward or backward at the handle.
Auxiliary power outletThe auxiliary power outlet supplies power to
the following electrical accessories when the
starter switch is in position1:
• The cigarette lighter*, available in con

junction with the ashtray*,
• The electric air pump, available in conjunc

tion with the tire repair kit*,
• Other consumers which operate up to a
maximum of 60W.!
The auxiliary power outlet can accommo

date 12V DC electrical accessories designed
for use with the standard “cigarette lighter”
plug type.
Keep in mind, however, that connecting
accessories to the auxiliary power outlet (for
example extensive connecting and discon

necting, or using plugs that do not fit proper

ly) can damage the auxiliary power outlet. With
the auxiliary power outlet damaged, the ciga

rette lighter* may no longer be able to be
placed in the heating (pushed
in) position, or
may pop out before it is hot enough. P68.60
2172
31
,
1 coupé only.

Tires and wheels
182
>> Operation Contact an authorized smart center for infor

mation on tested and recommended rims and
tires for summer and winter operation. They
can also offer advice concerning tire service
and purchase.
Modifications to the brake system and wheels
and the use of spacer and brake dust rings
are not permissible.
Important guidelines• Only use sets of tires and rims of the same
type and make.
• Tires must be of the correct size for the
rim.
• Break in new tires for approximately
60 miles (100 km) at moderate speeds.
• Regularly check the tires and rims for
damage. Dented or bent rims can cause tire
inflation pressure loss and damage to the
tire beads.
• If vehicle is heavily loaded, check tire infla

tion pressure and correct as required.
• Do not allow your tires to wear down too far.
Adhesion properties on wet roads are
sharply reduced at tread depths of less
than
1/8in (3 mm).
G
Warning!
Replace rims or tires with the same des

ignation, manufacturer and type as shown
on the original part. Contact an autho

rized smart center for further informa

tion. If incorrectly sized rims and tires
are mounted:
• The wheel brakes or suspension
components can be damaged.
• The operating clearance of the wheels
and the tires may no longer be correct.
G
Warning!
Worn, old tires can cause accidents. If the
tire tread is badly worn, or if the tires
have sustained damage, replace them.
When replacing rims, only use genuine
smart wheel bolts specified for the
particular rim type. Failure to do so can
result in the bolts loosening and possibly
an accident.
Retreaded tires are not tested or recom

mended by smart, since previous damage
cannot always be recognized on retreads.
The operating safety of the vehicle can

not be assured when such tires are used.

Tires and wheels
>> Operation
197
General:
Depending on the design standards used, the
tire size molded into the sidewall may have no
letter or a letter preceding the tire size des

ignation.
No letter preceding the size designation
(as illustrated above): Passenger car tire
based on European design standards.
Letter "P" preceding the size designation:
Passenger car tire based on U.S. design
standards.
Letter "LT" preceding the size designation:
Light Truck tire based on U.S. design
standards.
Letter "T" preceding the size designation:
Temporary spare tires which are high
pressure compact spares designed for
temporary emergency use only.
Tire width
Tire width1
(
page 196) indicates the
nominal tire width in mm.Aspect ratio
Aspect ratio2
(
page 196) is the dimen

sional relationship between tire section
height and section width and is expressed in
percentage. The aspect ratio is arrived at by
dividing section height by section width.
Tire code
Tire code3 (

page 196) indicates the tire
construction type. The "R" stands for radial
tire type. Letter "D" means diagonal or bias
ply construction; letter "B" means belted

bias ply construction.
At the tire manufacturer’s option, any tire
with a speed capability above 149 mph
(240 km/h) can include a "ZR" in the size
designation (for example: 245/40 ZR 18).
For additional information, see "Tire speed
rating" (

page 198)
.
Rim diameter
Rim diameter4 (

page 196) is the diameter
of the bead seat, not the diameter of the rim
edge. Rim diameter is indicated in inches (in).Tire load rating
Tire load rating5 (

page 196) is a numeri

cal code associated with the maximum load a
tire can support.
For example, a load rating of 91 corresponds
to a maximum load of 1 356 lbs (615 kg) the
tire is designed to support.
See also "Maximum tire load" (

page 201)
where the maximum load associated with the
load index is indicated in kilograms and lbs.
G
Warning!
The tire load rating must always be at
least half of the GAWR (

page 205) of
your vehicle. Otherwise, tire failure may
result and cause an accident and/or seri

ous personal injury to you or others.
Always replace rims and tires with the
same designation, manufacturer and type
as shown on the original part.

Tires and wheels
200
>> Operation Load identification
1
Load identification
i
For illustration purposes only. Actual data
on tires are specific to each vehicle and may
vary from data shown in above illustration.
In addition to the tire load rating, special load
identification1 may be molded into the tire
sidewall following the letter designating the
tire speed rating (

page 196).No specification given: absence of any text
(like in above example) indicates a standard
load (SL) tire.
XL (Extra Load): designates an extra load
(or reinforced) tire.
Light Load: designates a light load tire.
C, D, E: designates load range associated with
the maximum load a tire can carry at a speci

fied pressure.
DOT, Tire Identification Number (TIN)
U.S. tire regulations require each new tire
manufacturer or tire retreader to mold a TIN
into or onto a sidewall of each tire produced.
The TIN is a unique identifier which facilitates
efforts by tire manufactures to notify
purchasers in recall situations or other
safety matters concerning tires and gives
purchasers the means to easily identify such
tires.
The TIN is comprised of "Manufacturer’s
identification mark", "Tire size", "Tire type
code", and "Date of manufacture".
1
DOT
2
Manufacturer’s identification mark
3
Tire size
4
Tire type code (at the option of the tire
manufacturer)
5
Date of manufacture
i
For illustration purposes only. Actual data
on tires are specific to each vehicle and may
vary from data shown in above illustration.

Tires and wheels
>> Operation
201
DOT (D
epartment o
f T
ransportation)
Tire branding symbol1 (

page 200) which
denotes the tire meets requirements of the
U.S. Department of Transportation.
Manufacturer’s identification mark
Manufacturer’s identification mark2
(

page 200) denotes the tire manufacturer.
New tires have a mark with two symbols.
Retreaded tires have a mark with four
symbols. For more information on retreaded
tires (

page 182).
Tire size
Code3 (
page 200) indicates the tire size.
Tire type code
Code4 (
page 200) may, at the option of
the manufacturer, be used as a descriptive
code for identifying significant characteris

tics of the tire.
Date of manufacture
Date of manufacture5 (

page 200)
identifies the week and year of manufacture.The first two figures identify the week, start

ing with "01" to represent the first full week of
the calendar year. The second two figures
represent the year.
For example, "3202" represents the 32nd
week of 2002.
Maximum tire load
1
Maximum tire load rating
i
For illustration purposes only. Actual data
on tires are specific to each vehicle and may
vary from data shown in above illustration.The maximum tire load is the maximum weight
the tires are designed to support.
For more information on tire load rating
(

page 197).
For information on calculating total and cargo
load capacities (

page 187).
G
Warning!
Do not overload the tires by exceeding
the specified load limit as indicated on
the Tire and Loading Information placard
located on the driver’s door B
pillar.
Overloading the tires can overheat them,
possibly causing a blowout. Overloading
the tires can also result in handling or
steering problems, or brake failure.

Tires and wheels
204
>> Operation Tire ply material
1
Plies in sidewall
2
Plies under tread
i
For illustration purposes only. Actual data
on tires are specific to each vehicle and may
vary from data shown in above illustration.
This marking tells you about the type of cord
and number of plies in the sidewall and under
the tread.
Tire and loading terminologyAccessory weight
The combined weight (in excess of those stan

dard items which may be replaced) of auto

matic transmission, power steering, power
brakes, power windows, power seats, radio,
and heater, to the extent that these items are
available as factory
installed equipment
(whether installed or not).
Air pressure
The amount of air inside the tire pressing
outward on each square inch of the tire.
Air pressure is expressed in pounds per
square inch (psi), or kilopascal (kPa) or bars.
Aspect ratio
Dimensional relationship between tire section
height and section width expressed in per

centage.Bar
Another metric unit for air pressure. There
are 14.5038 pounds per square inch (psi)
to 1 bar; there are 100 kilopascals (kPa)
to 1 bar.
Bead
The tire bead contains steel wires wrapped by
steel cords that hold the tire onto the rim.
Cold tire inflation pressure
Tire inflation pressure when your vehicle has
been sitting for at least 3 hours or driven no
more than 1 mile (1.6 km).
Curb weight
The weight of a motor vehicle with standard
equipment including the maximum capacity of
fuel, oil, and coolant, and, if so equipped, air
conditioning and additional optional equip

ment, but without passengers and cargo.

Tires and wheels
206
>> Operation PSI (Pounds per s
quare i
nch)
A standard unit of measure for air pressure

> bar, kilopascal (kPa).
Recommended tire inflation pressure
The recommended tire inflation pressure for
normal driving conditions is listed on the Tire
and Loading Information placard located on
driver’s door B
pillar and provides best
handling, tread life and riding comfort.
Rim
A metal support for a tire or a tire and tube
assembly upon which the tire beads are
seated.
Sidewall
The portion of a tire between the tread and
the bead.TIN (T
ire I
dentification N
umber)
Unique identifier which facilitates efforts by
tire manufacturers to notify purchasers in
recall situations or other safety matters
concerning tires and gives purchasers the
means to easily identify such tires. The TIN is
comprised of "Manufacturer’s identification
mark", "Tire size", "Tire type code" and "Date
of manufacture".
Tire load rating
Numerical code associated with the maximum
load a tire can support.
Tire ply composition and material used
This indicates the number of plies or the num

ber of layers of rubber
coated fabric in the
tire tread and sidewall. Tire manufacturers
also must indicate the ply materials in the tire
and sidewall, which include steel, nylon, poly

ester, and others.Tire speed rating
Part of tire designation; indicates the speed
range for which a tire is approved.
Total load limit
Rated cargo and luggage load plus
68 kilograms (150 lbs) times the vehicle’s
designated seating capacity.
Traction
Force exerted by the vehicle on the road via
the tires. The amount of grip provided.
Tread
The portion of a tire that comes into contact
with the road.
Treadwear indicators
Narrow bands, sometimes called "wear bars"
that show across the tread of a tire when only
1/16in (1.6 mm) of tread remains.

Driving instructions
>> Operation
215 Drive sensibly
save fuel
Fuel consumption, to a great extent, depends
on driving habits and operating conditions.
To save fuel you should:
• Shift gears in a timely manner.
• Avoid frequent acceleration and decelera

tion.
• Keep tires at the recommended inflation
pressures.
• Remove carriers* when not in use.
• Remove unnecessary loads.
• Allow engine to warm up under low load use.
• Have all maintenance work performed at the
intervals specified in the Maintenance
Booklet and as required by the Maintenance
System. Contact an authorized smart cen

ter.
Fuel consumption is also increased by driving
in cold weather, in stop
and
go traffic, on
short trips, and in hilly areas.
Catalytic converterYour smart is equipped with monolithic
type
catalytic converter, an important element in
conjunction with the oxygen sensors to
achieve substantial control of the pollutants
in the exhaust emissions. Keep your vehicle in
proper operating condition by following our
recommended maintenance instructions as
outlined in your Maintenance Booklet.
G
Warning
The catalytic converter can become very
hot. Coming into contact with the catalytic
converter could result in burns.
Note the following:
• Do not remove the protective heat
guards.
• Do not apply any underseal.
• As with any vehicle, do not idle, park, or
operate this vehicle in areas where
combustible materials such as grass,
hay, or leaves can come into contact
with the hot exhaust system, as these
materials could be ignited and cause a
vehicle fire.