2008 SMART FORTWO COUPE adding oil

>> Keywords
5
Display message
Data bus . . . . . . . . . . . . . . . . . . . . . . . . . 236
Electronic immobilizer . . . . . . . . . . . . . . 236
Shifting system . . . . . . . . . . . . . . . . . . . . 236
Display, see Multifunction display
Door control panel . . . . . . . . . . . . . . . . . . . 44
Door handle . . . . . . . . . . . . . . . . . . . . . . . . . 85
Door locking system
Locking and unlocking from outside . . . . 83
DOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
Drive lock function . . . . . . . . . . . . . . . . . . . 84
Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Driving abroad . . . . . . . . . . . . . . . . . . . . . 223
Driving off
Uphill . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Driving safety systems
ABS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Activating the hazard warning flasher . . 76
ESP
® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Hydraulic brake assistant . . . . . . . . . . . . 75
Driving tips . . . . . . . . . . . . . . . . . . . . . . . . 211
Catalytic converter . . . . . . . . . . . . . . . . 215
Winter . . . . . . . . . . . . . . . . . . . . . . . . . . . 218
>> EElectric fuses . . . . . . . . . . . . . . . . . . . . . 282
Electrical and electronic devices, see Engine
electronics
Electronic immobilizer . . . . . . . . . . . . . . . 77
Display message . . . . . . . . . . . . . . . . . . 236
Electronic Stability Program, see "ESP
®"
Emergency Tensioning Device . . . . . . . . . 53
Emmission control . . . . . . . . . . . . . . . . . . 221
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Compartment . . . . . . . . . . . . . . . . . . . . 171
Electronics . . . . . . . . . . . . . . . . . . . . . . 290
Malfunction indicator lamp . . . . . . . . . . . 35
Starting . . . . . . . . . . . . . . . . . . . . . . . . . 122
Technical data . . . . . . . . . . . . . . . . . . . 297
Turning off . . . . . . . . . . . . . . . . . . . . . . 127
Engine oil . . . . . . . . . . . . . . . . . . . . . 172, 305
Adding . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Additives . . . . . . . . . . . . . . . . . . . . . . . . 305
Checking the oil level . . . . . . . . . . . . . . 173
Pressure indicator lamp . . . . . . . . . . . . . 35
EPS (Electronic Power Steering)*
Warning lamp . . . . . . . . . . . . . . . . . . . . 243
ESP
®(Electronic Stability Program) . 73, 243Exterior lamp switch . . . . . . . . . . . . . . . . 101
Exterior lighting
Overview . . . . . . . . . . . . . . . . . . . . . . . . 255
See also Brake lamp
See also Front fog lamps*
See also High beam headlamps
See also License plate lamps
See also Low beam headlamp
See also Parking lamps
See also Sidemarker lamps front/rear
See also Turn signal indicators
See also Turn signal lamps, side
Exterior rear view see Mirrors
Exterior view . . . . . . . . . . . . . . . . . . . . . . . 30
>> FFirst
aid kit* . . . . . . . . . . . . . . . . . . . . . . 235
Flat tire . . . . . . . . . . . . . . . . . . . . . . 234, 265
Fluid capacities . . . . . . . . . . . . . . . . . . . . 303
Front fog lamps* . . . . . . . . . . . . . . . 105, 255
Front lamps
Overview . . . . . . . . . . . . . . . . . . . . . . . . 255

Engine compartment
174
>> Operation Adding engine oil
!
Only use approved engine oils and oil fil

ters required for vehicles with Maintenance
System. For a listing of approved engine oils
and oil filters contact an authorized smart
center.
Using engine oils and oil filters of specifica

tion other than those expressly required for
the Maintenance System, or changing of oil
and oil filter at change intervals longer than
those called for by the Maintenance System
will result in engine or emission control sys

tem damage not covered by the smart Limited
Warranty.The filler cap is located in the engine
compartment on the passenger side.
1
Filler cap
>Unscrew filler cap
1
from filler neck.
>Add engine oil as required.
Do not add more than 0.53 US qt (0.5 l)
engine oil at a time.
>Wait one minute until the engine oil has run
into the oil pan.
>Check the engine oil level once more.
>Add engine oil once more if necessary.
G
Warning!
When adding engine oil, always use a fun

nel to avoid spilling oil on any hot parts
such as the catalytic converter or ex

haust system.
If this should happen, however, the en

gine must be thoroughly cleaned before
you continue your trip. The engine oil
could otherwise ignite.P01.00
2852
31

Engine compartment
>> Operation
175
Be careful not to spill any oil when adding to
avoid environmental damage caused by oil
entering the ground and water.!
Excess engine oil must be siphoned or
drained off. It could cause damage to the
engine or emission control system not
covered by the smart Limited Warranty.
>Screw filler cap
1
back on filler neck.
>Close the engine compartment cover.

Service fluids and capacities
>> Technical data.
309 Coolants
The engine coolant is a mixture of water and
anticorrosion/antifreeze, which provides:
• Corrosion protection
• Freeze protection
• Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection to
approximately
35°F (
37°C) and corrosion
protection.!
Add premixed coolant solution only.
Adding water and MB 325.0 Anticorrosion/An

tifreeze separately from each other, could
cause engine damage not covered by the
smart Limited Warranty.
If the antifreeze mixture is effective to
35°F
(
37°C), the boiling point of the coolant in the
pressurized cooling system is reached at
approximately 266°F (130°C).The coolant solution must be used year round,
even in countries which have high tempera

tures to provide the necessary corrosion
protection and increase boiling protection.
Refer to Maintenance/ Service Booklet for re

placement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the Mainte

nance booklet is only applicable if MB 325.0
Anticorrosion/Antifreeze solution or other
smart approved products of equal specifica

tion are used to renew the coolant concentra

tion or bring it back up to the proper level.
For information on other smart approved
products of equal specification, contact an
authorized smart center.
To provide important corrosion protection,
the solution must be at least 50% anticorro

sion/antifreeze (equivalent to freeze protec

tion to approximately
35°F [
37°C]).If you use a solution that is more than 55%
anticorrosion/antifreeze (freeze protection
to approximately
49°F [
45°C]), the engine
temperature will increase due to the lower
heat transfer capability of the solution.
Therefore, do not use more than this amount
of anticorrosion/antifreeze.
If the coolant level is low, water and MB 325.0
Anticorrosion/Antifreeze should be used to
bring it up to the proper level (have cooling
system checked for signs of leakage). Please
make sure the mixture is in accordance with
label instructions.
Always use anticorrosion/antifreeze that have
been approved by smart. For information
contact an authorized smart center.
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water. If you are
not sure about the water quality, consult an
authorized smart center.