2008 SKODA SUPERB technical data

Unlocking and locking39
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Note
•In the event of an accident in which the airbags are deployed, the locked doors
are automatically unlocked in order to enable rescuers to gain access to the vehicle.
•Only the driver's door can be unlocked using the key if the central locking
system fails ⇒ page 40, “Emergency unlocking and locking of the driver's door”.
You can lock or unlock manually the other doors and the boot lid.
−Emergency locking of the door ⇒page 41.
− Emergency unlocking of the boot lid ⇒page 43.
Safe securing
The central locking system is equipped with a safe securing system. Locking the
vehicle from the outside causes the door lock s to be automatically blocked. It is not
possible to open the doors with the door ha ndle either from the inside or from the
outside. This acts as an effective deterrent for attempts to break into your vehicle.
You can deactivate the safe securing syst em by locking two times within 2 seconds.
If the safe securing system is not operating:
•the indicator light in the driver door flashes for about 2 seconds fast, goes out
and starts to flash slowly after about 30 seconds,
•is the filler flap locked.
The safe securing system is again activate d the next time the vehicle is unlocked and
locked again.
If the vehicle is locked and the safe secu ring system is deactivated, you can open
the vehicle from the inside by pulling on the handle.
WARNING
If the vehicle is locked from the outside and the safe securing system is acti-
vated, there must not be any person and animals in the vehicle as it is then
not possible to open either a door or a window from the inside. The locked
doors make it more difficult for rescuers to get into the vehicle in an emer-
gency - hazard!
Note
The anti-theft alarm system* is also acti vated with the deactivated safe securing
system when locking the vehicle. The inte rior monitor* is however not activated.
Buttons for the central locking system
If the vehicle was not locked from outside, you can also unlock and lock
it with the rocker switch on the hand le of the driver or front passenger
door even without the ignition switched on.
Locking all doors and the boot lid
– Press on the bottom part of the button ⇒fig. 26 . The symbol
 in the
button comes on.
Unlocking all doors and the boot lid
– Press on the top part of the button ⇒fig. 26 . The symbol
 goes out
in the button.
The following applies if you have locked your vehicle using the central locking
system:
Fig. 26 Central locking
switch
NKO B6 20.book Page 39 Wednesday, March 26, 2008 3:15 PM

Unlocking and locking41
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Emergency locking of the doors
An emergency locking mechanism is located on the face side of the doors
which have no locking cylinder; it is only visible after opening the door.
Lock the doors using the vehicle key.
Locking
– Remove the panel ⇒fig. 28 .
– Guide the key into the slot and turn it to the outside.
– Re-insert the panel.
After closing the door, you can no longer op en it from outside. If the child safety
lock is not switched on, it is possible to op en the door from the inside by pulling on
the door handle. If the child safety lock is switched on, it is necesary to also open
the door from outside besides pulling on the inner door handle.
Twindoor - small boot lid
After unlocking the vehicle using the remote control or the key ⇒page 40
you can open the small boot lid ⇒fig. 30 .
Open small boot lid
– Press on the handle at the bottom side of the boot lid ⇒fig. 29 , the
boot lid lifts up automatically ⇒fig. 30 .
Close small boot lid
– Pull the boot lid down and close it with a slight swing ⇒. The
bonnet locks automatically.
Fig. 28 Rear door: Emer-
gency locking of the doorFig. 29 Handle of boot lid
Fig. 30 Boot lid
NKO B6 20.book Page 41 Wednesday, March 26, 2008 3:15 PM

Unlocking and locking43
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Close large boot lid
– Pull the boot lid down and close it with a slight swing ⇒. The
bonnet locks automatically.
A handle which makes the clos ing easier is located on the inner paneling of the
boot lid.
WARNING
•Ensure that the lock is properly enga ged after closing the boot lid. Other-
wise, the boot lid might open suddenly wh en driving even if the boot lid lock
is closed - risk of accident!
•Never drive with the boot lid fully opened or slightly ajar otherwise
exhaust gases may get into the interior of the vehicle - risk of poisoning!
Note
•After closing the boot lid, it is automatically locked within 2 seconds and
the anti-theft alarm system* is activated. This applies only if the vehicle was
locked before closing the boot lid.
•The function of the hand grip on the bottom edge of the boot lid is deactivated
after starting off or as of a speed of more than 5 km/hour. The function of the hand
grip is acitvated again after stopping the vehicle and after opening the driver or
front passenger door or after pressing the button on the remote control
⇒ page 44.
Emergency unlocking of the boot lid
If there is a fault in the central locking, you can open the boot lid as
follows:
– Fold the rear seats forwards ⇒page 76.
– Guide the key into the slot in the trip panel as far as the stop ⇒fig. 33 .
– You can unlock the boot lid by the movement in the direction of arrow.
– Open the boot lid/luggage compartment door from outside.
Remote control
Description
You can use the remote control:
•to unlock and lock the car,
•unlock or open the boot lid,
•opening and closing window.
A1
Fig. 33 Emergency
unlocking of the boot lid
NKO B6 20.book Page 43 Wednesday, March 26, 2008 3:15 PM

Unlocking and locking45
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Folding up of the key
– Press button and collapse the key bit in the housing.
The turn signal lights flash twice as confirmation that the vehicle has been
unlocked. The vehicle will lock again auto matically if you unlock the vehicle using
button but do not open a door or the boot lid within the next 30 seconds. This
function is intended to prevent th e car being unlocked unintentionally.
In addition, when the car is unlocked, the power seats and exterior mirrors* move
into the position assigned to this key. The stored setting of driver seat and exterior
mirrors is retrieved.
The interior lights and the lighting of th e entry area are automatically switched on
or off (if they have been set to operat e via door contact) when unlocking and
locking the vehicle.
Display of the locking
The turn signal lights flash once to co nfirm that the vehicle has been correctly
locked.
If the doors or the boot lid remain open after the vehicle has been locked, the turn
signal lights do not flash unt il they have been closed.
WARNING
If the vehicle is locked from the outside and the safe securing system is acti-
vated, there must not be any person in the vehicle as it is then not possible
to open either a door or a window from the inside. The locked doors make it
more difficult for rescuers to get into the vehicle in an emergency - hazard!
Note
•Operate the radio remote control only when the doors and boot lid are closed
and you have visual contact with the vehicle.
•Once in the car, you must not press the lock button  of the radio remote
control before inserting the key into the igni tion lock in order to avoid the car being
inadvertently locked and, in addition, the anti-theft alarm system* being switched
on. Should this happen, press the unlock button
 of the radio remote control.
Synchonisation of the remote control
If the vehicle cannot be unlock ed by actuating the remote control system then it is
possible that the code in the key and the control unit in the vehicle are no longer
synchronised. This can occur when the butt ons on the radio-operated key are actu-
ated a number of times outside of the operative range of the equipment or the
battery on the remote control was replaced.
This means it is necessary to synchronise the code as follows:
•Press any button on the remote control.
•after pressing the button, the door must be unlocked using the key within 1
minute ⇒ page 40, “Emergency unlocking and locking of the driver's door”.
Anti-theft alarm system*
Description
The anti-theft alarm system increases the level of protection against people seeking
to break into the vehicle. The system triggers audible and visual warning signals if
an attempt is made to break into the vehicle.
How is the alarm system activated?
The anti-theft alarm system is activated automatically when the vehicle is locked
with the key in the driver's door or by using the radio remote control ⇒page 40,
“Emergency unlocking and locking of the driver's door”. The door contact moni-
toring is activated approx. 15 seconds after the locking. The interior and the towing
protection monitoring are activated approx. 30 seconds after the locking. If a door
is opened during activation, the monito ring is only activated 5 seconds after
closing.
How is the alarm system deactivated?
The anti-theft alarm system is deactivate d by pressing the unlock button on the
remote control. The vehicle is automati cally locked again if the vehicle is not
opened within 30 seconds after reactivating the anti-theft alarm system.
A4
A1
NKO B6 20.book Page 45 Wednesday, March 26, 2008 3:15 PM

Unlocking and locking47
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
•The opened storage compartment for spectacles reduces the effectiveness of
the interior monitor. In order to ensure th e function to be fully operational, close
the storage compartment for specta cles before locking the vehicle.
Power windows
Buttons on the driver's door
The power windows operate only when ignition is switched on.
Opening a window
– A window is opened by pres sing lightly on the respective butto n in the
door. The process stops when one releases the button.
– Additionally you can open the window automatically (fully opened) by pressing the button up to the stop. Renewed pressing of the button
causes the window to stop immediately.
Closing a window
– A window is closed through pulling lightly on the respective button in
the door. The closing process stop s when one releases the button. – Additionally you can close the window automatically (fully closed) by
pulling the button up to the stop. Renewed pulling of the button
causes the window to stop immediately.
The switches for the individual windows are located in the armrest of the driver's
door ⇒fig. 36 , front passenger door and in the rear doors ⇒page 48, fig. 37
Buttons for the power window in the armrest of the driver's door Button for the power window in the driver's door
Button for the power window in the front passenger's door
Button for the power window at the rear right door
Button for the power window at the rear left door
Safety switch
Safety pushbutton
You can deactivate the switches for power windows at rear doors by pressing the
safety pushbutton ⇒fig. 36 . The buttons for power windows at rear doors are
activated again by pressing th e safety pushbutton again.
If the buttons for the rear doors are deactivated, the indicator light
 in the safety
switch lights up.
WARNING
•If you lock the vehicle from the outside, do not leave any person in the
vehicle since it is no longer possible to open the windows from the inside in
an emergency.
•The system is fitted with a force limiter ⇒page 48. The closing process
will be stop if an obstruction is detected and the window will open again. You
should then take particular care when closing the windows! You may other-
wis e suf fe r se v e re inj uri es a s a re s ult of g e tt ing a n ar m , for e xa m ple , ja m m e d
in the window!
•It is recommended to deactivate the electrically operated power
windows in the rear doors (safety pushbutton) ⇒fig. 36 when children
are being transported on the rear seats.
Fig. 36 Buttons on the
driver's door
AA
AB
AC
AD
AS
ASAS
AS
AS
NKO B6 20.book Page 47 Wednesday, March 26, 2008 3:15 PM

Unlocking and locking49
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
is stopped. During this time it is not possible to automatically close the window. The
force limiter is still switched on.
The force limiter is only switched off, if you attempt to close the window within the
next 10 seconds -
the window closes now with full strength!
If you wait longer than 10 seconds, the force limiter is switched on again.
WARNING
You should take particular care when closing the windows! You may other-
wi se s uffe r s e ve re i njur ie s a s a re sul t of getting an arm, for example, jammed
in the window!
Window convenience operation
You can open and close the electrically powered windows as follows when
unlocking and locking the vehicle (j ust closing of the sliding roof).
Opening a window
•by holding the pressed unlock button on the remote control,
•by holding the pressed top part of the button for the central locking system in
the driver door,
•by holding the key in the driver's lock in the unlock position ⇒page 40, “Emer-
gency unlocking and lockin g of the driver's door”.
Closing a window
•by holding the pressed lock button on the remote control,
•by holding the pressed bottom part of th e button for the central locking system
in the driver door,
•by holding the key in the driver's lock in the lock position ⇒page 40.
You can interrupt the opening or closing operation of the windows immediately by
releasing the key or the closing button.
WARNING
The system is fitted with a force limiter ⇒page 48. The closing process will
be stop if an obstruction is detected and the window will open again. You
should then take particular care when closing the windows! You may other-
wis e suf fe r se v e re inj uri es a s a re s ult of g e tt ing a n ar m , for e xa m ple , ja m m e d
in the window!
Note
•The convenience opening of the windows with the aid of the key in the driver's
lock is only possible 45 seconds after deactivating or activating the alarm system.
Operational faults
Electrically operated power windows do not operate
If the battery has been disconnected and then reconnected while the window was
opened, the electrically operated power windows do not operate. The system must
be activated. Proceed as follows in order to re-establish the function:
•you can close the window by pull ing the switch on the top edge.
•release the switch
•you must pull the switch again for approx. 3 seconds
Operation in winter
Ice accumulating on the surface of the wi ndows during the winter may result in a
greater resistance when closing the windows and the window may stop and move
back several centimetres
Proceed as follows to close the window fully:
•Turn the key in the lock of the driver d oor into the closing position and hold it
there until all of the windows are closed.
•If the window closing is interrupted, it is necessary to put the force limiter out of
operation ⇒page 48.
NKO B6 20.book Page 49 Wednesday, March 26, 2008 3:15 PM

Unlocking and locking51
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Closing
Sliding closed/closing the sliding/tilting roof
– Turn the switch to position ⇒page 50, fig. 38 .
Safety closing
The sliding/tilting roof is equipped with an overload protection system. If an
obstacle (e.g. ice) prevents closing, the sliding/tilting roof stops and opens
completely. You can close the sliding/tilting roof completely without overload
protection by pressing the switch to the position ⇒page 50, fig. 38 at the front
for as long as it takes for the sliding/tilting roof to shut completely ⇒.
WARNING
Close the sliding/tilting roof carefully - risk of injury!
Convenience operation
You can also close an open sliding/tilting roof from the outside.
– Keep pressed the lock button on th e remote control or hold down the
key in the driver's door in the lock position until the sliding/tilting roof
is closed ⇒.
The closing process stops when one releases the key or the closing button.
WARNING
Close the sliding/tilting roof carefully - risk of injury! The overload protec-
tion system does not function with the convenience closing.
Emergency operation
You can close and/or open the sliding/tilting roof by hand if the system is
defect.
– Position the flat blade of a screwdriver carefully against the rear edge
of the cover of th e electrical drive ⇒fig. 39 .
– Pull the cover down.
– Take the crank out of the holder on the safety cover at the side of the
dash panel. Insert the crank up to the stop into the opening ⇒fig. 40
and close and/or open the sliding/tilting roof ⇒fig. 40 .
AA
AAFig. 39 Detail of the head-
liner: point for positioning
screwdriver
Fig. 40 Detail of the head-
liner: Emergency operation
NKO B6 20.book Page 51 Wednesday, March 26, 2008 3:15 PM

Lights and Visibility53
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Lights and Visibility
Lights
Switching lights on and off 
Switching on side lights
– Turn the light switch into position
.
Switching on the low beam and main beam
– Switch on the ignition.
– Turn the light switch into position
.
– Press the main beam lever forward in order to switch on the main beam ⇒page 60, fig. 47 .
Switching off lights (except daylight driving lights)
– Turn the light switch into position.
When the parking lights are switched on, the symbol  next to the light switch is
illuminated. Low beam comes on only if the ignition is
switched on. After switching off the igni-
tion, the low beam is switched off automati cally and only the side lights come on.
On models fitted with right-hand steering the position of certain switches differs
from that shown in ⇒fig. 41 . The symbols which mark the switch positions are
identical, however.
WARNING
Never drive with side lights on - risk of accident! The side lights are not
bright enough to light up the road suffic iently in front of you or to be seen by
other oncoming traffic. In this case, always switch on the low beam when it
is dark or if visibility is poor.
Note
•An audible warning will sound if you wi thdraw the ignition key and open the
driver's door when the vehicle lights are still on.
•The acoustic warning signal is switched off over the door contact when the
driver's door is closed (ignition off). The vehicle can be parked with the side lights
on.
•If the car is parked for a lengthy period , we recommend switching off all lights,
or leaving only the parking lights switched on.
•The switching on of the described lights should only be undertaken in accord-
ance with the legal requirements.
•If a fault occurs in the light switch , the low beam comes on automatically
•In the event of cool or humid weather co nditions, the headlights can be misted
up from inside.
−The temperature difference between interior and external area of the head-
light lenses is decisive.
− When the driving lights are switched on , the light outlet surfaces are free
from mist after a short period. The headlight lenses can possibly mist up at the
border areas.
Fig. 41 Dash panel: Light
switch
NKO B6 20.book Page 53 Wednesday, March 26, 2008 3:15 PM