2008 SKODA OCTAVIA Owner's Manual

Fuses and light bulbs
264
Positions of the light bulbs in the front headlight ⇒page 263, fig. 240 .
- Front turn signal light
- parking lights and low beam
- main beam light
Removing the headlight
The headlight must be removed in order to change the light bulb of the
parking lights, low beam lights and main beam lights as well as the turn
signal lights.
Removing the headlight
– Switch the ignition and all lights off.
– Open the bonnet ⇒ page 224.
– Unscrew the plastic nut ⇒fig. 241 .
– Pull the fuse in upward direction.
– Pull the locking lever of the headlight as far as the stop in the direction of arrow . – Unplug the plug connector and carefully take out the headlight in the
direction of arrow .
Installation takes place in the reverse order.
Note
We recommend that you have the headlight setting checked by a specialist garage
after installing the headlight.
Turn signal light (at the front)
Changing light bulb for turn signal light (at the front)
– Switch the ignition and all lights off.
– Remove the headlight ⇒page 264.
– Turn the socket in the direction of arrow OPEN (open) and take it out
together with the light bulb for the turn signal light ⇒fig. 242 .
– Press the defective light bulb into the socket, turn to the left and remove.
– Press a new light bulb into the socket and turn the light bulb to the right as far as the stop.
AA
AB
AC
Fig. 241 Front headlight:
Installing the light bulbs
AA
AB
A1
A2
Fig. 242 Removing the light
bulb for the turn signal light
20A5Facelift.book Page 264 Saturday, September 6, 2008 2:13 PM

Fuses and light bulbs265
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
– Insert the socket with the changed light bulb into the headlight and
secure it by turning in the direction of arrow CLOSE (close) to the
right.
Note
We recommend that you have the headlight setting checked by a specialist garage
after installing the headlight.
Front parking lights and low beam
Removing the light bulb for the parking light
– Switch the ignition and all lights off.
– Remove the headlight ⇒page 264.
– Remove the protective cap ⇒page 263, fig. 240 .
– Remove the socket ⇒fig. 243 .
– Take the faulty bulb out of the fixture and insert a new one.
– Insert the protective cap. Removing the light bulb for the low beam light
– Switch the ignition and all lights off.
– Remove the headlight ⇒
page 264.
– Remove the protective cap ⇒page 263, fig. 240 .
– Turn the connector with the light bulb up to the stop towards the left and remove ⇒fig. 243.
– Replace the lamp, insert the connector with the new lamp and turn to the right up to the stop.
– Insert the protective cap.
Note
•In order to facilitate the removal of th e bulb for the parking lights, we recom-
mend to remove first of all the bulb for the low beam light.
•We recommend that you have the headli ght setting checked by a specialist
garage after installing the headlight.
Main beam light
– Switch the ignition and all lights off.
Fig. 243 Removing the bulbs
for the parking and low beam
light
AB
AA
AB
AB
Fig. 244 Removing the light
bulb for the main beam light
20A5Facelift.book Page 265 Saturday, September 6, 2008 2:13 PM

Fuses and light bulbs
266
– Remove the headlight ⇒page 264.
– Remove the protective cap ⇒page 263, fig. 240 .
– Unplug plug ⇒page 265, fig. 244 .
– Press the wire clamps in the direction of the headlight and then unhook them to the side.
– Remove the light bulb and insert the new light bulb in such a way that the fixing lugs of the light bulb socket fit into the recesses at the
reflector.
Installation takes place in the reverse order.
Note
We recommend that you have the headlight setting checked by a specialist garage
after installing the headlight.
Fog lights and daylight driving lights*
Connector - bulb for daylight driving lights* ⇒fig. 246. Connector
- bulb for fog lights.
Removing the cover
– Switch the ignition and all lights off.
– Insert the fingers in the opening ⇒fig. 245 .
– By pulling in the direction of arrow , first of all slacken the cover in the upper area on the side to the fog lights.
– Afterwards, also slacken the cover on the other side in the direction of arrow and remove it.
Removing the fog light
– Guide your hand into the openin g which has become available and
press the interlock ⇒fig. 246.
– Take out the fog light.
– Turn the connector with the light bulb up to the stop towards the left
and remove.
– Replace the lamp, insert the connector with the new lamp and turn to the right up to the stop.
AC
AA
AB
AC
Fig. 245 Front bumper:
Protective grille
Fig. 246 Removing the front
bumper
AAAB
AA
A1
A2
20A5Facelift.book Page 266 Saturday, September 6, 2008 2:13 PM

Fuses and light bulbs267
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
– For the installation, first of all inse rt the fog light with the interlock to
the side far away from the marking of the vehicle.
– Press into place the headlight onto the side facing the marking.
– In order to reinstall the cover, first of all insert one part of the cover starting on the side of the marking. Then press the cover closed on the
side to the fog lights. The cover must engage firmly.
Light unit (Octavia)
Changing light bulbs in the lamp holder
– Switch the ignition and all lights off.
– Unlock the locking button and open the cover of the lamp holder ⇒fig. 247 .
– Press the catches in the direction of arrow and take out the lamp holder ⇒fig. 248 .
– Press the defective light bulb into the socket, turn to the left and remove.
– Press a new light bulb into the socket and turn the light bulb to the right as far as the stop.
– Insert the lamp holder in such a wa y that the catches lock in place in
the housing.
– Close and lock the cover of the lamp holder.
Changing light bulb for tail light
– Switch the ignition and all lights off.
– Unlock the locking button and open the cover of the lamp holder ⇒fig. 247 .
– Take the defective light bulb (arrow or ⇒fig. 248 ) out of the
housing and replace it with a new one.
– Close and lock the cover of the lamp holder.
Fig. 247 Luggage compart-
ment: Cover for the lamp
holder
Fig. 248 Removing the lamp
holder
A1A2
20A5Facelift.book Page 267 Saturday, September 6, 2008 2:13 PM

Fuses and light bulbs
268
Rear light unit (estate car)
Changing light bulbs in the lamp holder
– Switch the ignition and all lights off.
– Remove the side compartment cover by turning the locks in the direc-
tion of arrow ⇒ fig. 249.
– Take out the cover of the lamp holder on the luggage compartment side.
– Take out the light bulbs of the tail light (arrow and ) ⇒fig. 250 .– Press the catches in the direction of arrow and take out the lamp
holder.
– Press the defective light bulb into the socket, turn to the left and remove.
– Press a new light bulb into the socket and turn the light bulb to the right as far as the stop.
Changing light bulb for tail light
– Switch the ignition and all lights off.
– Remove the side compartment cover by turning the locks in the direc- tion of arrow ⇒fig. 249 .
– Take out the cover of the lamp holder on the luggage compartment side.
– Take the defective light bulb (arrow or ⇒page 267, fig. 248 ) out
of the housing and replace it with a new one.
– Remove the lamp holder cover on the luggage compartment side and close the side compartment.
Fig. 249 Luggage compart-
ment: Side compartment
Fig. 250 Removing the lamp
holder
A1A2
A1A2
20A5Facelift.book Page 268 Saturday, September 6, 2008 2:13 PM

Technical Data269
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Technical Data
Technical Data
General information
The details given in the official vehicle registration documents always take prece-
dence over the details in th e Owner's Manual. Please refer to the official vehicle
registration documents or consult your Škoda Service Partner concerning the
engine with which your vehicle is equipped.
Used abbreviations
Performances
The listed performance values were de termined without performance-reducing
equipment, e.g. air conditioning system.
Weight
The loading capacity is reduced in line with the range of the special equipment. The
unloaden weight contains a fuel tank topped up to 90%. A driver with a weight of
75 kg is also included in the value.
Identification details
Vehicle data sticker
The vehicle data sticker ⇒fig. 251 is located on the floor of the luggage compart-
ment and is also stated in the Service schedule.
AbbreviationImportance
kWKilowatt, measuring unit for the engine output
rpmEngine revolutions per minute
NmNewton meter, measuring unit for the engine torque
g/kmdischarged quantity of carbon dioxide in grams per
driven kilometer
RONResearch octane number, me asuring unit for the knock-
ing resistance of petrol
FSIFuel Stratified Injection
TSIDirect fuel injection system for engines with turbocharger
M5 / M65-speed/6-speed manual gearbox
AG66-speed automatic gearbox
DQ6/DQ76 speed-/7 speed automatic gearbox DSG
DPFDiesel particle filter
Fig. 251 Vehicle data sticker
20A5Facelift.book Page 269 Saturday, September 6, 2008 2:13 PM

Technical Data
270
The vehicle data sticker co ntains the following data:
Vehicle identification number (VIN)
Vehicle type
Gearbox code, paint number, interior equipment number, engine output,
engine code
Partial description of the vehicle
7GG, 7MB, 7MG - vehicles with DPF ⇒page 200
Vehicle identification number (VIN)
The vehicle identification num ber - VIN (vehicle body number) is stamped into the
engine compartment on the right hand shoc k absorber dome. This number is also
located on a sign on the lower left hand edge below the windscreen.
Engine number
The engine number is stamped into the engine block.
Type plate (production plate)
The type plate is located in the lower area of the left centre column.
Homologation sign
The homologation sign is located on the in side of the bonnet next to the lock. Vehi-
cles for certain countries do not have an homologation sign.
Sticker on inside of fuel filler flap
The stickers are affixed to the inside of th e fuel filler flap and contain the following
information:
•The prescribed types of fuel,
•Tyre si z e,
•Tyre pressure.
Fuel consumption according to the regulations
(99/100/EU)
Depending on the range of the special equipment, style of driving, traffic situation,
weather influences and vehi cle condition, the consumption values which in prac-
tice result when using the vehicle ca n deviate from the indicated values.
Urban traffic
The consumption measurement in urban traf fic begins with starting of the cold
engine. Afterwards the normal urban traffic is simulated.
Non-urban traffic
For the consumption measurement in non-ur ban traffic the vehicle, as in daily
motoring, is accelerated and braked several times in all gears. The vehicle speed
changes within the range from 0 to 120 km/h.
Combined traffic
The consumption value in the combined traf fic consists of 37% from the value for
the urban traffic and of 63% from the value for the non-urban traffic.
A1
A2
A3
A4
A5
20A5Facelift.book Page 270 Saturday, September 6, 2008 2:13 PM

Technical Data271
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Dimensions
Dimensions (mm)
OCTAVIAOCTAVIA RSCOMBICO M B I R SCOMBI 4x4SCOUT
Length456945784569457945694581
Width176917691769176917691784
Width including exterior mirror201820182018201820182018
Height
1462
1485a)
1449b)
a)The value is valid for vehicles with rough road package.b)The value corresponds to the status with SPORT package.
1447
1468
1490a)
1455b)14511495
1520a)1533
Clearance140128140128138180
Wheel base257825782578257825782577
Tr a c k g a u g e f r o n t / r e a r1541/15141528/15081541/15141528/15081535/15081531
20A5Facelift.book Page 271 Saturday, September 6, 2008 2:13 PM