2008 SKODA OCTAVIA Owner's Manual

Communication
144
mobile phone in the interior of the ve hicle and the charging of the telephone
battery is interrupted.
Note
•Please also refer to the additional instructions ⇒page 160, “Mobile phones
and two-way radio systems”.
•Please contact your Škoda Service Partner if there are any points which are not
clear.
Bluetooth®
The Bluetooth® technology serves as ca bleless connection of a
mobile phone to a hands-free system of your vehicle.
In order to connect a mobile phone with Bluetooth® to the hands-free
system, it is necessary to adapt th e phone and the hands-free system to
each other. Detailed information on this is provided in the operating
instructions of your mobile phone. The following steps must be carried
out for the connection:
– Switch on the ignition.
– Select Bluetooth
® on the mobile phone and select the menu with
which the mobile phone searches for suitable Bluetooth® devices.
– If the hands-free system on the display of the mobile phone announces Skoda UHV , enter the PIN° 1234 within 30 seconds and
wait, until the connection is established.
17)
While connecting the mobile phone with the hands-free system by means of Blue-
tooth®, no other phone can be connected wi th the hands-free system via Blue-
tooth®. Up to three mobile phones can be connected to the hands-free system by means
of Bluetooth
®, whereby only one mobile phone can communicate via Bluetooth®
with the hands-free system. If a fourth mobile phone is connected to the hands-
free-system, then the telephone, which has not been used together with the hands-
free-system for the longest period, is disconnected by means of Bluetooth
®.
Establish Bluetooth
® connection
After switching on the ignition, the Blue tooth connection is automatically estab-
lished for the already adapted mobile phone
17). Check on the mobile unit if the
automatic connection was established.
Disconnect Bluetooth
® connection
After withdrawing the ignition key, the Bluetooth® connection is disconnected.
WARNING
•Pay attention primarily to the traffic situation! As the driver you are fully
responsible for road safety. Use the telephone system only to such an extent,
so that you are in full control of your vehicle at any time - risk of accident!
•In the event of air transport, the Bluetooth® function of the handsfree-
system must be switched off by a specialist garage!
Caution
Taking the mobile phone out of the adapter during the call can lead to interruption
of the connection. When taking out th e mobile phone, the connection to the
factory-fitted antenna is interrupted, this reduces the quality of the transmitting
and receiving signal. This might result additionally in harmful radiation from the
mobile phone in the interior of the ve hicle and the charging of the telephone
battery is interrupted.
Note
•Not valid for all mobile phones which enable a communication via Bluetooth®.
You can ask at a Škoda Service Partner if your telephone is compatible with the
universal telephone preinstallation GSM II.
17)Some mobile phones have a menu, in which the authorization for establishing a Bluetooth®
connection is performed via the input of a code. If the input for the authorization is neces-
sary, it must always be performed when re-establishing the Bluetooth connection.
20A5Facelift.book Page 144 Saturday, September 6, 2008 2:13 PM

Communication145
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
•Please operate your mobile phone exclus ively with a suitable adapter in order
to keep a low radiation in the vehicle.
•Inserting the mobile phone into the adapter ensures an optimal sending and
receiving power and offers at the same ti me the advantage of the battery charging.
•Note that the range of the Bluetooth® connection to the handsfree-system is
limited to the vehicle interior. The range is dependent on local factors, e.g. obstacles
between the devices and interferences with other devices. If your mobile phone is
e.g. in a jacket pocket, this can lead to difficulties when establishing the Bluetooth
®
connection with the handsfree-system or the data transfer.
Inserting the mobile phone with the adapter*
Only one telephone mount* is factory-fitted. An adapter for the phone
can be purchased from the Škoda original accessories.
Inserting the mobile phone with the adapter
– First of all push the adapter in the direction of arrow ⇒fig. 160 up
to the stop into the mo unt. Press the adapter slightly downwards, until
it locks securely into position.
– Insert the mobile phone into the adapter (as specified in manufac- turer's instructions). Removing the mobile phone with the adapter
– Press simultaneouly the side locks of the mount and remove the
mobile phone and adapter ⇒fig. 160 .
Operating telephone calls with the aid of the adapter*.
The voice control of the telephone is acti vated by pressing the button PTT (button
push to talk)  on the adapter ⇒fig. 161 or ⇒fig. 162 .
If you insert the adapter with the telephone in the telephone mount, the handsfree-
system connects to the telephone by means of the interface of the adapter. If the
Fig. 160 Universal prepara-
tion for the phone
AA
AA
Fig. 161 Illustration image:
Single-button adapter
Fig. 162 Illustration image:
Two-button adapter
20A5Facelift.book Page 145 Saturday, September 6, 2008 2:13 PM

Communication
146
telephone is connected to the handsfree-system via Bluetooth®, this connection is
interrupted.
Adapter “Bluetooth only”
For the adapters which are marked with the “Bluetooth only” logo, the complete
communication between the telephone and the handsfree-system of your vehicle
is carried out only with the help of the Bluetooth
® technology. If an adapter marked
in such a way is inserted in the telephon e mount, it only serves for recharging the battery of the telephone and for transmit
ting the signal onto the outer vehicle
aerial.
Aside from the button PTT, the button SOS can be found on certain adapters
⇒ page 145, fig. 162 . This button is without function.Note
The adapters illustrated are only prime examples.
Operation of the telephone on the multifunction steering wheel*
The driver can set the basic functions of the telephone by simply operating the
buttons located on the steering wheel so th at he can concentrate on the traffic situ-
ation without being distracted as little as possible by operating the telephone
⇒ fig. 163 .
This applies only if your vehicle has been equiped with the telephone preinstalla-
tion at the factory.
If the side lights are switched on, the buttons on the multifunction steering wheel
are illuminated.
Overview of the different functions in cont rast to the multifunction steering wheel
without mobile phone operation ⇒page 141.
Fig. 163 Multifunction
steering wheel: Control
buttons for the telephone
20A5Facelift.book Page 146 Saturday, September 6, 2008 2:13 PM

Communication147
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
The buttons operate the functions for
the operating mode of the current
telephone.
Operate telephone in the information display*
If you select the menu point Te l e p h o n e on the information display with the aid of
the handwheel , you can change to the following menus:
„Phone book
„Last calls
„Received calls
„Missed calls Phone book
In the menu point
Phone book is the list of the loaded contacts from the telephone
memory and the SIM card of the mobile phone. In the phone phonebook there are
1500 free memory locations available.
ButtonActionOperation
press brieflyActivation and deactivation of the voice control (Button PTT - Push to talk)
 turn upwardsIncrease volume
 turn downwardsDecrease volume
 press brieflyAccept call, terminate call, entry in the main me nu of the telephone, list of selected numbers
 press button for a long
timeReject call, entry in the main menu of the telephone, list of selected numbers
 press brieflyReach one level higher in the menu (according to the current position in the menu)
 press button for a long
timeReturn in the main menu of the information display
press brieflyConfirm menu selection
press button for a long period of timeConfirming the selected menu point, the following initial letters in the telephone book
 turn upwardsThe last chosen menu selection, name
 turn downwardsThe next menu selection, name
A1
A1
A1
A2
A2
A3
A3
A4
A4
A4
A4
A4
20A5Facelift.book Page 147 Saturday, September 6, 2008 2:13 PM

Communication
148
Voice commands
Voice commands for mobile phone operation
Voice commands for operating the phone phone book Other possible commands
Enter PIN code
A PIN code must be entered before operating the system.
– Press the PTT button.
– Give the command
ENTER PIN/PIN CODE after the signal tone.
After this command the PIN code can be entered.
The entry of the PIN code is only possible if:
•The ignition and
•the mobile phone is in the mount;
Voice commandActivity
ENTER PIN/PIN CODEAfter this command the PIN code of the mobile
phone can be entered ⇒page 148.
DIAL NUMBERAfter this command a telephone number can be
entered which establishes a connection to the
requested partner ⇒page 149.
REDIALAfter this command the la st selected telephone
number is selected again ⇒page 149.
Voice commandActivity
SAVE/STORE
NAMES/NAME/NUMBE
RAfter this command a name with its telephone
number can be stored in the phone phone book
⇒page 150.
SELECT NAMES/NAMEAfter this command a telephone number which was
stored under its given name in the phone phone
book can be selected ⇒page 150.
DELETE NAMES/NAMEAfter this command a name in the phone phone
book can be erased ⇒page 151.
LISTEN TO/PLAY
PHONEBOOKAfter this command you can listen-in to the phone
phone book ⇒page 152.
DELETE PHONEBOOKAfter this command the complete phone book or a
name can be erased ⇒page 151.
Voice commandActivity
DIALThe telephone number is selected.
STORE
In addition to the name in the phone book, which is
selected on the information display, a voice recording
is stored to select with the help of the voice com-
mands or the entered PIN code.
REPEATThe entered name or the digits are repeated. Then the
system requests with voice response “ please pro-
ceed ” the entry of further digits or commands.
BACK
The entered name or the last entered order of digits is
erased. Previously entered groups of digits are
repeated. Then the system requests with voice
response “ please proceed ” the entry of further digits
or commands.
DELETE
All entered digits are erased. Then the system
requests with voice response “ The number is
deleted. The number please ” the entry of further
digits or commands.
CANCELThe dialogue is ended.
20A5Facelift.book Page 148 Saturday, September 6, 2008 2:13 PM

Communication149
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
•the mobile phone are switched on.
The digits zero to nine are permitted. The system detects no continuous digit
combinations such as twenty-three, but only individually spoken digits (two, three).
After each order of digits (separation through brief voice pause) the detected digits
are repeated.
Notes for entering the PIN code
•When entering a PIN code with more than 8 digits, the system indicates “The
PIN is too long ”.
•When entering an incorrect PIN code, the system indicates “ The PIN is incor-
rect ”.
•If the incorrect PIN code has been ente red three times consecutively, the card
is blocked. With the aid of the person al unblocking code PUK (Personal Unblock
Key), the SIM card can be unblocked. The unblocking code can only be entered
via the phone keypad and not through the voice control.
Example for entering the PIN code
You can interrupt the dialogue at any time by pressing the PTT button or with the
voice command CANCEL.
Select number
– Press the PTT button. – Give the command
DIAL NUMBER after the signal tone.
After giving this command, the system re quests the entry of a telephone number.
The telephone number can be entered as an interconnected spoken row of digits
(complete number), in the form of order of digits (separation through a brief voice
pause) or through individually spoken digits. After each order of digits (separation
through brief voice pa use) the detected digits are repeated.
The digits zero to nine are permitted. The system detects no continuous digit
combinations such as twenty-three, but only individually spoken digits (two, three).
If you enter more than 20 digits, the system announces: “ The number is too long”.
Additionally for international calls a Plus (+) has to be entered in front of the 20
digits.
Example when entering a telephone number
You can interrupt the dialogue at any time by pressing the PTT button or with the
voice command CANCEL.
Repeat last call
– Press the PTT button.
– Give the command REDIAL after the signal tone.
Voice commandAnnouncement
ENTER PIN/PIN CODE“The PIN please ”.
e.g. ZERO ONE TWO THREE“Zero One Two Three ”.
If no entry is put in, the following anno uncement is made after about 5 seconds.
“Possible commands are: store, repeat,
correct, delete or more digits ”.
STORE“The PIN is saved ”.
(end of dialogue)
Voice commandAnnouncement
DIAL NUMBER“ The number please ”.
e.g. ZERO SIX ZERO THREE“Zero Six Zero Three ”.
If no entry is put in, the following anno uncement is made after about 5 seconds.
“Possible commands are: dial, repeat,
correct, delete or more digits ”.
FIVE SEVEN TWO“Five Seven Two ”.
DIAL“The number is being dialed ”.
20A5Facelift.book Page 149 Saturday, September 6, 2008 2:13 PM

Communication
150
After giving this command, the last numbe r selected via voice input is selected
again.
Example of redial
You can interrupt the dialogue at any time by pressing the PTT button or with the
voice command CANCEL.
Phone voice phonebook*
Store name
– Press the PTT button.
– Give the command SAVE/STORE NAMES/NAME/NUMBER after the
signal tone.
After giving this command, the system re quests the entry of a name and a tele-
phone number which should be stored in the phone voice phonebook. In the
phone voice phonebook up to 50 entries can be stored.
The telephone number can be entered as an interconnected spoken row of digits
(complete number), in the form of order of digits (separation through a brief voice
pause) or through individually spoken digits. After each order of digits (separation
through brief voice pause) the detected digits are repeated.
The digits zero to nine are permitted. The system detects no continuous digit
combinations such as twenty-three, but only individually spoken digits (two, three).
If you enter more than 20 di gits, the system announces: “ The number is too long”.
Additionally a Plus (+) has to be entered in front of the 20 digits.
The stored entry is shown on the information display* with an asterisk in front of
the name.
For similar names additional information (e.g. first names) should be stored. Example for storing in th
e phone voice phonebook
You can interrupt the dialogue at any time by pressing the PTT button or with the
voice command CANCEL.Select name
– Press the PTT button.
– Give the command DIAL/SELECT NAMES/NAME after the signal
tone.
After giving this command, there is the possibility to select a stored entry out of the
phone voice phonebook.
Voice commandAnnouncement
REDIAL“ The number is being dialed ”.
Voice commandAnnouncement
SAVE/STORE
NAMES/NAME/NUMBER“The name please ”.
COMPANY XYZ“Please repeat the name ”.
COMPANY XYZ“The number please ”.
ZERO ONE TWO THREE“Zero One Two Three ”.
FOUR FIVE SIX“Four Five Six ”.
If no entry is put in, the following anno uncement is made after about 5 seconds.
“Possible commands are: store, repeat, correct,
delete or more digits ”.
STORE“The name COMPANY XYZ is stored ”.
20A5Facelift.book Page 150 Saturday, September 6, 2008 2:13 PM

Communication151
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Example for selecting an entry out of the phone voice phonebook
You can interrupt the dialogue at any time
by pressing the PTT button or with the
voice command CANCEL.
Delete names
– Press the PTT button.
– Give the command DELETE NAMES/NAME after the signal tone.
After giving this command, there is the possibility to erase a stored entry in the
phone voice phone book.
Example for erasing an entry out of the phone phonebook You can interrupt the dialogue at any time
by pressing the PTT button or with the
voice command CANCEL.
If the user answers with NO, the system answers with “ Cancel” and the dialogue is
ended.
Delete voice phonebook
– Press the PTT button.
– Give the command DELETE PHONEBOOK after the signal tone.
After giving this command there is the possibility to erase the complete phone
voice phone book or the individually st ored names out of the phone phone book.
Example for erasing the complete phonebook
You can interrupt the dialogue at any time by pressing the PTT button or with the
voice command CANCEL.
Voice commandAnnouncement
SELECT NAMES/NAME“The name please ”.
CO M PA N Y X Y Z“Company xyz ”.
If no entry is put in, the following anno uncement is made after about 5 seconds.
“Possible commands are: dial, repeat, correct”.
DIAL“The number is being dialed ”.
Voice commandAnnouncement
DELETE NAMES/NAME“The name please ”.
CO M PA N Y X Y Z“Do you want to delete the entry Company
xyz?”.
YES“ Delete? ”.
If no entry is put in, the following anno uncement is made after about 5 seconds.
“Possible commands are: yes, no, repeat, cor-
rect ”.
YES“The name is deleted ”.
Voice commandAnnouncement
DELETE PHONEBOOK“Do you want to delete the whole
phonebook? ”.
If no entry is put in, the following anno uncement is made after about 5 seconds.
“Possible commands are: yes, no,
repeat ”.
YES“Are you sure? ”.
YES“The phonebook is deleted ”.
20A5Facelift.book Page 151 Saturday, September 6, 2008 2:13 PM