2008 RENAULT SCENIC instrument panel

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -364
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -364V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP39 Accessories feed not activated
NOTESCheck the voltage of the battery.
Start the fault finding procedure with the ignition off and the vehicle locked.
When the vehicle is unlocked, the instrument panel should light up for a moment.
If not, carry out fault finding on the multiplex network and instrument panel.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
The vehicle should switch to timed power (approximately 20 minutes) after the driver's door is opened (ET053
Driver's door).
If the timed supply is not triggered, try by:
–pressing the Start button (ET070 Start button), or
–turning on the hazard warning lights (ET085 "Hazard warning lights button"), or
–switching on the side lights (ET081 Lighting switch position).
If correct, run status fault finding for the faulty component.
If not correct, apply ALP No dialogue with the UCH.
The vehicle goes into accessories feed mode when the Start button is pressed (timed power active).
If it does not conform, check the operation of the Start button using status ET070 Start button and apply the fault
finding procedure associated with this status if necessary.
If the Start button operates correctly, use the fault finding procedure for status ET075 + accessories feed present.
Run fault finding and check the condition of the connectors of the + battery housing (Power fuses), of the power
board (maxi fuses), of the Protection and Switching Unit (UPC), of the Passenger Compartment Fuse and
Relay Box, of the Passenger Compartment Fuse and Relay Box option, and of the relay boards.
Check the condition and connection of the connectors on the UCH and the connectors on the UPC.
Check for + 12 V on connections BTP and 13AC of component 645.
Check for earth on connections 13E and NAM of component 645.
If one of the connectors is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP39 /UCH_V48_ALP39/UCH_V4C_ALP39/
UCH_V4D_ALP39/UCH_V4F_ALP39/UCH_V50_ALP39

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -365
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -365V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP40 Forced after-ignition feed fails
NOTESCheck the voltage of the battery.
Carry out a fault finding procedure on the function.
Test with the other card.
Switching to + accessories feed should work.
If not deal with ALP39 Accessories feed not activated first.
It can be checked while trying to activate after ignition feed if the verlog indicator light:
–Remains on, meaning that the steering lock is not recognised.
–Remains on for 3 seconds and flashes at 4 Hz, meaning the card is not recognised.
Review of the procedure for forcing after ignition feed:
+ accessories supply off, card in the card reader, starting conditions not met and after
pressing and holding the Start button (approximately 5 seconds).
Make sure that there is no Insert card message on the instrument panel.
Check that status ET008 Blank UCH is NO.
Refer to the procedure for this status if necessary (Blank UCH).
Check that status ET110 UCH request to UPC or injection becomes + after ignition feed after a request for
forced after ignition.
If everything is correct, run fault finding on the UPC.
Make sure the steering column lock functions properly by checking in particular that:
–statuses:
–ET071 Steering column lock blank is NO.
–ET072 Steering column lock is UNLOCKED.
–ET073 Steering column lock sensor signal is UNLOCKED.
See the procedure for these statuses if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP40 /UCH_V48_ALP40/UCH_V4C_ALP40/
UCH_V4D_ALP40/UCH_V4F_ALP40/UCH_V50_ALP40

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -366
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -366V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP41The vehicle does not start and the after ignition feed fails with the
card in the card reader
NOTESCheck the voltage of the battery.
First carry out a function fault finding check.
Switching to + accessories feed should work.
If not deal with ALP39 Accessories feed not activated first.
Check that the start-up conditions are met:
It can be checked while attempting to start if the immobiliser warning light:
–Remains on, meaning that the steering lock is not recognised.
–Remains on for 3 seconds and flashes at 4 Hz, meaning the card is not recognised.
It can also be checked while trying to start; if the Start button flashes, the card
has not been detected or recognised.
If the message "Insert card" is displayed on the instrument panel.
Insert the card in the card reader and run the special command SC005 Check card:
If the message "The inserted card cannot be detected or is not fully inserted into the card reader.
Check the card and the condition of the card reader. If the fault is still present, consult the fault finding for the
customer complaint in the fault finding manual (ALP41 for MEGANE II and ALP21 for CLIO III)" appears, try one
of the other vehicle's cards or a card from another MEGANE II vehicle.
–If the message appears again, apply the fault finding procedure for DEF014 Card reader circuit CC.0.
–If the message has disappeared and the result of the test is accessible, replace the defective card.
Check that status ET120 Card recognised by vehicle is definitely YES:
If ET120 Card recognised by vehicle is NO, the card does not belong to the vehicle or is damaged.
Check that status ET012 Card allocated to vehicle is definitely YES:
If ET012 Card allocated to vehicle is NO, the card is no longer allocated to the vehicle: re-allocate the vehicle's
cards using the special command SC006 Card allocation.
If the fault is still present, contact the Techline.
If the message "Insert card" is not displayed on the instrument panel.
Make sure statuses:
–ET008 Blank central unit is NO.
–ET071 Steering column lock blank is NO
See the procedure for these statuses if necessary.
Check that status ET110 UCH request to injection or UPC becomes START after a starting request is made
when the start conditions are met.
If everything is correct, run fault finding on the UPC.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP41 /UCH_V48_ALP41/UCH_V4C_ALP41/
UCH_V4D_ALP41/UCH_V4F_ALP41/UCH_V50_ALP41

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -370
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -370V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP45 Impossible to stop engine
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Check whether the engine switches off if the Start button is pressed twice.
If it does, make sure the card is not considered absent by the UCH, particularly by checking for messages on the
instrument panel.
Check that the button presses are detected correctly by the UCH using status ET070 Start button.
If not, see the procedure for dealing with this status.
Check that status ET110 UCH request to injection or UPC is STOP when the button is pressed.
If there is a fault, see the procedure for this status.
Check the consistency of parameter PR008 Vehicle speed with the vehicle stationary.
If not, run fault finding on the ABS.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP45 /UCH_V48_ALP45/UCH_V4C_ALP45/
UCH_V4D_ALP45/UCH_V4F_ALP45/UCH_V50_ALP45

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -372
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -372V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP47 Steering column lock does not unlock
NOTES–The immobiliser warning light flashes normally,
–the card reader does not flash,
–there is a message on the instrument panel Column not unlocked or Turn
steering wheel + Start.
Check that the steering column is not under any mechanical stress (e.g.: wheel(s) jammed against pavement).
If the steering column is under stress, try to start the vehicle again by lifting the steering column (and pulling the
card out of the reader if a message requests this).
Check the consistency of statuses ET072 Steering column lock and ET073 Steering column lock signal.
In the event of a fault, see the procedure for these statuses in the UCH section.
Check that the steering column lock belongs to the vehicle using status ET248 Steering column lock immobiliser
code.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP47 /UCH_V48_ALP47/UCH_V4C_ALP47/
UCH_V4D_ALP47/UCH_V4F_ALP47/UCH_V50_ALP47

87B-385
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V9 MR-372-J84-87B000$990.mif
87B
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
Note: In Vdiag 44 vehicles, the Service warning light comes on with the instrument panel message.
ALP 52"Adjust tyre pressure" message appears
(the wheel concerned is highlighted on the display)
NOTESCheck that all the faulty tyres are fitted with tyre pressure monitor valves.
Make sure the tyre has the recommended
pressure specified on the label or in the
driver's handbook (not under- or over-
inflated).
Are the tyres at the recommended
pressures?Readjust the tyre inflation pressure.
Read the pressures in PR003
to PR006.
Do PR003 to PR006 match
the readings taken with the
pressure gauge (to within
0.2 bar)?Read the recommended
pressures in the UCH
(PR009 to PR012)
Do the values of these
parameters match the
manufacturer's
recommended
pressures?Write the recommended
pressures with command
VP005 Enter
recommended
pressures.
Program the four valve codes and reinstall the coloured rings in the
position indicated on the label on the driver's side.
NO
YES
YES
NO
ANO
YES
UCH_V44_ALP52 / UCH_V48_ALP52 / UCH_V4C_ALP52 / UCH_V4D_ALP52 / UCH_V4F_ALP52 / UCH_V50_ALP52
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart

87B-387
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V9 MR-372-J84-87B000$990.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP 53"Adjust tyre pressure" message appears
(2 wheels are highlighted on the display)
Note:
In Vdiag 44 vehicles, the Service warning light comes on with the instrument panel message.
NOTESCheck that all the faulty tyres are fitted with tyre pressure monitor valves.
Is there a pressure
imbalance between the left-
hand and right-hand tyre on
the same axle?Check the positions of
the coloured rings
against the label on the
driver's side.
Program the four valve
codes and reinstall the
coloured rings in the
position indicated on
the label on the driver's
side. Have the front and rear
tyres been swapped?
Adjust the tyre pressure to the
manufacturer's recommended
levels.
Is the fault still present?End of fault finding.
NO
YESYES
NO
B
NO
YES
A
UCH_V44_ALP53 / UCH_V48_ALP53 / UCH_V4C_ALP53 / UCH_V4D_ALP53 / UCH_V4F_ALP53 / UCH_V50_ALP53

87B-390
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V9 MR-372-J84-87B000$990.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP 55"Tyre sensor fault" message appears
(4 wheel warning lights disappear)
NOTESCheck that all the faulty tyres are fitted with tyre pressure monitor valves.
Are the wheels fitted with tyre pressure
monitor valves?Either install tyre pressure monitor valves, or
deconfigure tyre pressure monitor in the
instrument panel.
Check the tyre pressure monitor configuration
in the UCH (LC017 Tyre pressure monitor
function).
Is the UCH configured "with" the tyre
pressure monitor function?Configure the UCH with the tyre pressure monitor
function using command CF023 Tyre pressure
monitor function under SC008 UCH type.
Program the four valve codes with command
SC002 Program the 4 valve codes. Have the valve codes been programmed?
Check that the ABS is transmitting the vehicle
speed (PR008 Vehicle speed).
Is there an ABS fault?Run full fault finding on the ABS.
UCH fault, contact Techline.
NO
YES
NO
YES
NO
YES
YES
NO
UCH_V44_ALP55 / UCH_V48_ALP55 / UCH_V4C_ALP55 / UCH_V4D_ALP55 / UCH_V4F_ALP55 / UCH_V50_ALP55