2008 RENAULT SCENIC rims

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-48
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87B
87B-48V9 MR-372-J84-87B000$129.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
MATCHING THE VALVE TO THE TYRE
Whenever wheels are swapped over, reprogram the new valve positions in the UCH using the diagnostic tool.
The coloured rings will then have to be placed back in the location marked on the label on the driver's door.
Ring colours:
–Front left-hand: green.
–Front right-hand: yellow.
–Rear left-hand: red.
–Rear right-hand: black.
WINTER AND SUMMER TYRES
On leaving the factory, it is the summer wheel set that is configured in the UCH, but customers can fit their vehicle
with a winter set (winter wheels = wheel rims + sensors + special tyres).
The first time a set of winter wheels is fitted, program the codes of the four valves. Thereafter, whenever the set of
tyres is changed, recognition is automatic without having to touch the UCH.
Establishing communication between the UCH and the CLIP diagnostic tool:
–Connect the wire to the diagnostic socket and switch on the ignition.
–Switch on the diagnostic tool.
–Select the vehicle type and carry out the multiplex network test.
–Select the Tyre function.
–Follow the fault finding procedure described previously.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 331
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 331V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
ALP21Rear left-hand window does not operate
(Rear one-touch electric windows)
NOTESUse the Wiring Diagram Technical Note and a multimeter.
Only check this customer complaint after performing a complete check with the
diagnostic tool.
For vehicles with Mégane II phase 2 bodywork, see 87D Electric windows -
Sunroof, Fault finding chart.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Remove the rear left-hand window winder switch (see MR 364 (Mégane) or MR 370 (Scenic) Mechanical
systems, 87D, Electric windows - Sunroof, Rear window winder switch: Removal - Refitting) and disconnect
its connector.
Shunt connections 20AL and 23C of component 131 to lower the window (to raise the window, shunt
connections 23D and 20AL of component 131).
Does the window move?
NO YES
Remove the rear left-hand door trim (see MR 365
(Mégane) or MR 371 (Scenic) Bodywork, 72A,
Side opening trims, Rear side door trim:
Removal - Refitting) and disconnect the connectors
from the LH rear window winder and from the LH rear
window winder switch.
Check the continuity of the following connections:
●Connection code 23D.
●Connection code 23C between
components 131 and 202.
Is the continuity good?
YES
Replace the rear left-hand window winder switch
(see MR 364 (Mégane) or MR 370 (Scenic)
Mechanical systems, 87D, Electric windows -
Sunroof, Rear window winder switch on rear
door: Removal - Refitting).
If there is a repair procedure (see Technical Note
6015A, Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise
replace it.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP21 /UCH_V48_ALP21/UCH_V4C_ALP21/
UCH_V4D_ALP21/UCH_V4F_ALP21/UCH_V50_ALP21
MR-372-J84-87B000$946.mif

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 333
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 333V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP22Rear right-hand window does not operate
(Rear one-touch electric windows)
NOTESUse the Wiring Diagram Technical Note and a multimeter.
Only check this customer complaint after performing a complete check with the
diagnostic tool.
For vehicles with Mégane II phase 2 bodywork, see 87D Electric windows -
Sunroof, Fault finding chart.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Remove the rear right-hand window winder switch (see MR 364 (Mégane) or MR 370 (Scenic) Mechanical
systems, 87D, Electric windows - Sunroof, Rear window winder switch: Removal - Refitting) and disconnect
its connector.
Shunt connections 20AL and 23A of component 132 to lower the window (to raise the window, shunt
connections 23B and 20AL of component 131).
Does the window move?
NO YES
Remove the rear right-hand door trim
(see MR 365 (Mégane) or MR 371 (Scenic)
Bodywork, 72A, Side opening trims, Rear side
door trim: Removal - Refitting) and disconnect
the connectors from the RH rear window winder
and from the RH rear window winder switch.
Check the continuity of the following connections:
●Connection code 23B.
●Connection code 23A between
components 130 and 201.
Is the continuity good?
YES
Replace the rear left-hand window winder switch
(see MR 364 (Mégane) or MR 370 (Scenic)
Mechanical systems, 87D, Electric windows -
Sunroof, Rear window winder switch on rear
door: Removal - Refitting).
If there is a repair procedure (see Technical Note
6015A, Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise
replace it.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP22 /UCH_V48_ALP22/UCH_V4C_ALP22/
UCH_V4D_ALP22/UCH_V4F_ALP22/UCH_V50_ALP22