2008 RENAULT SCENIC key

MULTIMEDIA
Fault finding - Role of components
86C
86C - 10V5 MR-372-J84-86C050$260.mif
ITS
Program no.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Role of components
4 - Role of main components
●Receiver: the receiver transmits audio signals via the speakers inside the vehicle.
●Display: displays different multimedia information such as the station tuned in, the time, or information related to
CDs or satellite navigation.
●Steering column switch: different multimedia functions can be accessed via controls on the steering wheel.
●Speakers and tweeter speakers: produce sound from the multimedia system inside the vehicle.
●CD multi-changer: loads CDs and sends audio signals to the receiver.
●AM/FM aerial: picks up waves from various transmitters.
●GPS aerial: receives various signals emitted by satellites.
●Navigation central control: different multimedia functions can be intuitively accessed via a multimedia keypad.
●Microphone: enables a phone to be used in hands-free mode via a Bluetooth connection.
●Navigation computer: manages the various multimedia system functions according to the requests of the user.
●DVD cartographic map: loads maps onto the navigation computer.
●AM/FM aerial amplifier: improves the reception of AM/FM signals.
ITSJ84ph2V1.0
MR-372-J84-86C050$260.mif

MULTIMEDIA
Fault finding - Replacement of components86C
86C-11V5 MR-372-J84-86C050$312.mif
ITS
Program No.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Replacement of components
To remove and refit this computer (see MR 370 Mechanical, 83C, On-board telematics system, Navigation
computer: Removal - Refitting).
Procedures to be carried out before replacing the navigation computer:
1. Before replacing the computer (with the agreement of the Techline), read the faults and carry out a conformity
check to ensure that it is definitely faulty.
2. Eject the DVD.
3. Before removing the computer, clear the customer's data (telephone numbers, address book, etc.) using
command RZ003 Parameters and customer data in the diagnostic tool.
4. Remove the computer with the ignition off.
The navigation computers from the Parts Department are supplied unconfigured and in factory mode (receiver set to
162 kHz AM, and beeps for 2 minutes).
Procedures to be carried out after replacing the navigation computer:
1. Enter the unlocking code for the CARMINAT NAVIGATION AND COMMUNICATION system.
–How to obtain the unlocking code for the Carminat Navigation and Communication system
●switch on + after ignition feed,
●switch on the CARMINAT NAVIGATION and COMMUNICATION system,
●connect the Clip diagnostic tool,
●note the number of the navigation programming key written in the Identification menu,
●contact Techline with this navigation programming number to obtain the Carminat Navigation
and Communication system unlocking code,
●the unlocking code is requested 2 mins after the CARMINAT NAVIGATION and COMMUNICATION system
comes on,
●enter this code using the navigation central control.
2. Configure the computer (see Configurations and Programming).
–Enter the vehicle type via the CF001 Vehicle type command.
–For vehicles registered in the Netherlands only, complete the VP004 Netherlands Legislation configuration.
Note:
(only for vehicles registered in the Netherlands)
If the computer is replaced. Depending on the manufacturing date of the vehicle:
–BEFORE 01 JANUARY 2006, it is essential to run command VP004 Netherlands Legislation
(LC002 Netherlands)
–AFTER 01 JANUARY 2006, command VP004 Netherlands Legislation (LC002 Except Netherlands) must not
be run under any circumstances.
3. Enter the VIN code (see Dealing with commands).
–Use command VP002 Write VIN to enter the VIN. Note:
If the code is incorrect, you must wait for between 2 and 32 minutes before entering a new code.
Delete the incorrect code before entering the new one.
ITSJ84ph2V1.0
MR-372-J84-86C050$312.mif

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 21V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF027
PRESENT
OR
STOREDNO AUDIO CD CHANGER SIGNALS
1.DEF : No communication with the CD changer keypad
NOTESConditions for applying fault finding procedures to stored faults:
Apply this fault finding procedure if the fault reappears as present or stored after the
fault has been cleared, the ignition switched off and back on again and the audio
system started after using the CD multi-changer several times.
Order of priority in the event of more than one fault:
Deal with fault DF022 No radio multiplex signal first.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition of the 15A fuse (component code 260) and the 7.5A fuse (component code 1337).
Check the condition and connection of the CD changer (component code 1272) and of the receiver C2 (green)
connector (component code 261) (broken, oxidised, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
With ignition on, check for + 12 V on connections SP2, AP43 and BCP3 of the component 1272 connector.
Check that the earth on the MAN connection on the component 1272 connector is perfect.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 34HT,
●connection code 34HR,
●connection code TB29,
●connection code 34HS,
between components 1272 and 261.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF027ITSJ84ph2V1.0