2008 PONTIAC GRAND PRIX start stop button

{CAUTION:
It is dangerous to get out of your vehicle if
the shift lever is not fully in PARK (P) with the
parking brake rmly set. Your vehicle can roll.
Do not leave your vehicle when the engine
is running unless you have to. If you have
left the engine running, the vehicle can move
suddenly. You or others could be injured.
To be sure your vehicle will not move, even
when you are on fairly level ground, always
set your parking brake and move the shift
lever to PARK (P). SeeShifting Into PARK (P)
on page 2-34. If you are pulling a trailer,
seeTowing a Trailer on page 4-29.Make sure the shift lever is fully in PARK (P) before
starting the engine. The vehicle has an automatic
transmission shift lock control system. You must fully
apply your regular brakes rst and then press the
shift lever button, located on the front of the shift lever,
before you can shift from PARK (P) when the ignition
key is in RUN. If the vehicle cannot be shifted out
of PARK (P), ease pressure on the shift lever by pushing
it all the way into PARK (P) as you maintain brake
application. Then press the shift lever button and move
the shift lever into another gear. SeeShifting Out of
PARK (P) on page 2-35.
REVERSE (R):Use this gear to back up.
Notice:Shifting to REVERSE (R) while your vehicle
is moving forward could damage the transmission.
The repairs would not be covered by your warranty.
Shift to REVERSE (R) only after your vehicle is
stopped.
To rock the vehicle back and forth to get out of snow,
ice or sand without damaging the transmission, see
If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow
on page 4-21.
2-29

Anti-lock Brake System (ABS)
Warning Light
For vehicles with
the Antilock Brake
System (ABS), this
light comes on briey
when the engine
is started.
That is normal. If the light does not come on then, have it
xed so it will be ready to warn you if there is a problem.
If the ABS light stays on, turn the ignition off, if the light
comes on when you are driving, stop as soon as it is
safely possible and turn the ignition off. Then start the
engine again to reset the system. If the ABS light still
stays on, or comes on again while you are driving,
your vehicle needs service. If the regular brake system
warning light is not on, your vehicle still has brakes, but
not antilock brakes. If the regular brake system warning
light is also on, your vehicle does not have antilock
brakes and there is a problem with the regular brakes.
SeeBrake System Warning Light on page 3-45.
For vehicles with a Driver Information Center (DIC),
seeDIC Warnings and Messages on page 3-67for
all brake related DIC messages.
Traction Control System (TCS)
Warning Light
If the vehicle has
the Traction Control
System (TCS), this light
may come on for the
following reasons:
The traction control button, located on the center
console, is pressed, turning the system off. The
light will stay on. To turn the system back on,
press the button again and the warning light should
go out. SeeTraction Control System (TCS) on
page 4-6for more information.
If there is a brake system problem that is specically
related to traction control, the TCS will turn off and
the warning light will come on.
If the brakes begin to overheat, the TCS will turn off
and the warning light will come on until the brakes
cool down.
If the TCS warning light comes on and stays on for an
extended period of time when the system is turned
on, the vehicle needs service.
3-47

AVERAGE SPEED:The average speed is displayed in
miles per hour (mph) or kilometers per hour (km/h).
The average speed is calculated from the various
vehicle speeds recorded since the last reset of this
menu item. To reset the average speed, press the
set/reset button. The display will return to zero.
Press the trip odometer button again to advance to
the next screen.
TIME ELAPSED:This screen can be used as a
stopwatch. The display can show the hours, minutes
and seconds. The elapsed time indicator will record up
to 99 hours, 59 minutes and 59 seconds, then it will
reset to zero and continue counting.
To set the time elapsed function:
1. Press the set/reset button for less than two seconds
to start or stop the timer.
2. Press and hold the set/reset button for more than
two seconds to reset the timer back to zero.
Press the trip odometer button again to advance to
the next screen.
Set/Reset
r(Set/Reset):Press this button to set or reset a
mode item when using the trip odometer or option
buttons.
Options
4(Options):Press this button to access the Date,
Language, Display Units, Daytime Display Enhancement,
Engine Oil Monitor System, Compass Calibration,
Personal Programming modes, and Tire Pressure
readings.
Date:This menu sets the date.
The time is set through the radio. SeeSetting the
Clock on page 3-95for more information.
To set the date:
1. Press the options button until the date is displayed
on the DIC.
2. Press the set/reset button to access the RESET
YEAR screen. The second position in the year
will be selected. Press and hold the set/reset button
to scroll through the available digits. Release the
button when the correct digit appears.
3. Press the options button to advance to the rst
position in the year. Press and hold the set/reset
button to scroll through the available digits.
Release the button when the correct digit appears.
4. Press the options button to advance to the
months of the year.
3-58

Radio Messages for XM™ Only
SeeXM Radio Messages on page 3-114later in
this section for further detail.
Playing a CD
Radio with CD (Base)
Insert a CD partway into the slot, label side up. The
player pulls it in and the CD should begin playing. If you
want to insert a CD when the ignition is off, rst press
the eject button or push the RCL knob. If you insert a CD
with the radio off and the ignition on, it starts to play.
Radio with CD (MP3)
Insert a CD partway into the slot, label side up. The
player pulls it in and READING DISC and the CD symbol
appears on the display. If you want to insert a CD
with the ignition off, rst press the EJECT button or
push the RCL knob.
When a CD is inserted, the CD symbol appears on
the display. As each new track starts to play, the track
number appears on the display.
If the ignition or radio is turned off with a CD in the
player it stays in the player. When the ignition or radio
is turned on, the CD starts to play where it stopped,
if it was the last selected audio source.For vehicles that have a radio with a Six-Disc CD
player, see the following:
LOAD / CD
Z:Press the LOAD side of this button to
load CDs into the CD player. This CD player holds up
to six CDs.
To insert one CD, do the following:
1. Turn the ignition on.
2. Press and release the LOAD button.
3. Wait for the indicator light, located to the right of
the slot, to turn green.
4. Load a CD. Insert the CD partway into the slot,
label side up. The player pulls the CD in.
To insert multiple CDs, do the following:
1. Turn the ignition on.
2. Press and hold the LOAD button for two seconds.
A beep sounds and the indicator light, located to
the right of the slot, begins to ash.
3. Once the light stops ashing and turns green, load
a CD. Insert the CD partway into the slot, label side
up. The player pulls the CD in.
Once the CD is loaded, the light begins ashing
again. Once the light stops ashing and turns green
you can load another CD. The CD player takes
up to six CDs. Do not try to load more than six.
3-103

RDM 2 / RDM 3 / RDM (Random):Depending on the
radio, press this button to hear the tracks in random,
rather than sequential, order. RDM and the track number
displays. Press RDM again to turn off random play.
For the Radio with Six-Disc CD player, the tracks can
be listened to in random order, on one CD or on all
of the CDs.
To use random on the Radio with Six-Disc CD player,
do one of the following:
To play the tracks on the CD in random order, press
and release the RDM button. RANDOM ONE
displays. Press RDM again to turn off random play.
To play the tracks on all of the CDs that are loaded in
random order, press and hold RDM for more than
two seconds. A beep sounds and RANDOM ALL
displays. Press RDM again to turn off random play.
#3 (Next Folder):This button does not have a
function for non-MP3 CDs. Press this button to go to
the next MP3 folder.
4
sor{REV (Reverse):Depending on the radio
that your vehicle has, the reverse arrows will look
different, but they function the same. Press and hold
this button to reverse quickly within a track. Sound
is heard at a reduced volume. Release this pushbutton
to play the passage. The elapsed time of the track
displays.6
!(Previous Folder):This button does not have a
function for non-MP3 CDs. Press this button to go to
the previous MP3 folder.
EQ or AUTO EQ (Equalization):Press EQ, or
depending on the radio, AUTO EQ, to select the desired
customized equalization setting while playing a CD.
The equalization is automatically set when a CD
is played. See “EQ” or “AUTO EQ” listed previously for
more information.
wSEEKx(Radios with CD):Press the SEEK
arrows to go to the previous or to the next track. Press
either arrow for more than two seconds to search
the previous or next tracks at two tracks per second.
When the desired track number displays, release
the arrow to stop searching and to play the track.
sSEEKt(Radio with Six-Disc CD Player):Press
the left arrow to go to the start of the current track, if more
than ten seconds have played. Press the right arrow to go
to the next track. If either arrow is held or pressed more
than once, the player continues moving backward or
forward through the CD.
wSCANx(Radios with CD):Press and hold either
arrow for more than two seconds until SCAN and the
track number displays and a beep sounds. The CD goes
to the next track, plays for a few seconds, then goes to
the next track. Press either arrow again to stop scanning.
3-105

sSCANt(Radio with Six-Disc CD Player):
To scan one CD, press and hold either SCAN arrow for
more than two seconds until SCAN displays and a
beep sounds. The radio goes to the next track, plays for
10 seconds, then goes to the next track. Press either
SCAN arrow again, to stop scanning.
To scan all loaded CDs, press and hold either SCAN
arrow for more than four seconds until CD SCAN
displays and a beep sounds. Use this feature to listen
to 10 seconds of the rst track of each loaded CD.
Press either SCAN arrow again, to stop scanning.
RCL (Recall):Push this button, or depending on the
radio, press the RCL knob, to see how long the current
track has been playing. To change the default on the
display, track and elapsed time, push the button until the
desired option displays, then hold the button until the
display ashes. The selected display is now the default.
BAND:Depending on the radio, press this button to
listen to the radio when a CD is playing. The inactive
CD(s) remains inside the radio for future listening.
CD AUX (Auxiliary):Press this button to play a CD
while listening to the radio.Care of Your CDs
If playing a CD-R, the sound quality can be reduced
due to CD-R quality, the method of recording, the quality
of the music that has been recorded, and the way the
CD-R has been handled. Handle them carefully.
Store CD-R(s) in their original cases or other protective
cases and away from direct sunlight and dust. The
CD player scans the bottom surface of the disc. If the
surface of a CD is damaged, such as cracked, broken,
or scratched, the CD does not play properly or not
at all. Do not touch the bottom side of a CD while
handling it; this could damage the surface. Pick up CDs
by grasping the outer edges or the edge of the hole
and the outer edge.
If the surface of a CD is soiled, take a soft, lint free cloth
or dampen a clean, soft cloth in a mild, neutral detergent
solution mixed with water, and clean it. Make sure the
wiping process starts from the center to the edge.
If there is no apparent damage, try a known good CD.
3-106

Order of Play
Tracks are played in the following order:
Play begins from the rst track in the rst playlist
and continues sequentially through all tracks in
each playlist. When the last track of the last playlist
has played, play continues from the rst track of
the rst playlist.
If the CD does not contain any playlists, then play
begins from the rst track under the root directory.
When all tracks from the root directory have
played, play continues from les according to
their numerical listing. After playing the last track
from the last folder, play begins again at the
rst track of the rst folder or root directory.
When play enters a new folder, the display does not
automatically show the new folder name unless
you have chosen the folder mode as the default display.
See RCL later in this section for more information.
The new track name appears on the display.
File System and Naming
The song name that is displayed is the song name that is
contained in the ID3 tag. If the song name is not present
in the ID3 tag, then the radio displays the le name
without the extension (such as .mp3) as the track name.Track names longer than 32 characters or four pages
are shortened. Parts of words on the last page of
text and the extension of the lename does not display.
Preprogrammed Playlists
Preprogrammed playlists that were created by
WinAmp™, MusicMatch™, or Real Jukebox™ software
can be accessed, however, they cannot be edited
using the radio. These playlists are treated as special
folders containing compressed audio song les.
Playing an MP3
Insert a CD partway into the slot, label side up. The
player pulls it in, and READING displays. The CD
should begin playing and the CD symbol appears on the
display. If you want to insert a CD with the ignition off,
rst press the EJECT button or the RCL knob.
If the ignition or radio is turned off with a CD in the
player it stays in the player. When the ignition or radio
is turned on, the CD starts to play where it stopped,
if it was the last selected audio source.
As each new track starts to play, the track number
appears on the display.
3-111

wSEEKx:Press the up arrow to go to the start of
the next track. Press the down arrow to go to the start of
the previous track. Pressing either arrow for more than
two seconds searches the previous or next tracks at
two tracks per second. When the track number that
you would like to play appears on the display, release
the arrow to stop searching and to play the track.
TUNE:Turn this knob to fast track reverse or advance
through tracks in all folders or playlists. The track
number and le name appears on the display for each
track. Turn this knob while in random to fast track
reverse or advance the tracks in sequential order.
RCL (Recall):Push this knob to switch between track
mode, folder/playlist mode, and time of day mode.
The display shows only 13 characters, but there can
be up to three pages of text. If there are more than
13 characters in the song, folder, or playlist name
pushing this knob within two seconds takes you to the
next page of text. If there are no other pages to be
shown, pushing this knob within two seconds takes
you to the next display mode.
Track mode displays the current track number and
the ID3 tag song name.Folder/playlist mode displays the current folder or
playlist number and the folder/playlist name.
Time of day mode displays the time of day and the
ID3 tag song name.
To change the default on the display, push this knob
until you see the desired display, then hold this knob
for two seconds. The radio produces one beep and the
selected display is now the default.
INFO (Information):INFO displays whenever a current
track has ID3 tag information. Press this button to
display the artist name and album contained in the tag.
INFO disappears from the display when the information
in the ID3 tag has nished.
BAND:Press this button to listen to the radio when a
CD is playing. The inactive CD remains inside the radio
for future listening.
CD AUX (Auxiliary):Press this button to play a CD
when listening to the radio. The CD symbol appears on
the display when a CD is loaded.
EJECT:Press this button to eject a CD. Eject may
be activated with either the ignition or radio off.
CDs may be loaded with the radio and ignition off if
this button is pressed rst.
3-113