2008 Peugeot 407 C Owner's Manual

1
28
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer’s servicing schedule.
Once an engine oil level indication has
been displayed, the display indicates
the total and trip distances.
If the service is overdue , each time
the ignition is switched on and for
5 seconds, the distance and the span-
ner fl ash.

Example: when the ignition is switched
on and for 5 seconds, the display in-
dicates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal op-
eration and the spanner remains lit.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last service.
The distance remaining may be
weighted by the time factor, depend-
ing on the user’s driving habits.
Engine oil temperature indicator
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone C , the
temperature is correct.
When the needle is in zone D , the
temperature is too high.
Reduce your speed to lower the tem-
perature. Operation
As soon as the ignition is switched on
and for 5 seconds, the spanner sym-
bolising the service operations is lit.
The trip recorder display shows the
distance remaining (in round fi gures)
before the next service.

Example: when switching on the ig-
nition and for 5 seconds, the display
shows that 900 miles/km remain be-
fore the next service is due.

1
28
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer’s servicing schedule.
Once an engine oil level indication has
been displayed, the display indicates
the total and trip distances.
If the service is overdue , each time
the ignition is switched on and for
5 seconds, the distance and the span-
ner fl ash.

Example: when the ignition is switched
on and for 5 seconds, the display in-
dicates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal op-
eration and the spanner remains lit.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last service.
The distance remaining may be
weighted by the time factor, depend-
ing on the user’s driving habits.
Engine oil temperature indicator
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone C , the
temperature is correct.
When the needle is in zone D , the
temperature is too high.
Reduce your speed to lower the tem-
perature. Operation
As soon as the ignition is switched on
and for 5 seconds, the spanner sym-
bolising the service operations is lit.
The trip recorder display shows the
distance remaining (in round fi gures)
before the next service.

Example: when switching on the ig-
nition and for 5 seconds, the display
shows that 900 miles/km remain be-
fore the next service is due.

1
Service indicator zero re-set
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service your-
self, the re-set procedure is as follows:

 Switch off the ignition,

 Press and hold the trip recorder
re-set button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for approx-
imately 5 seconds, after the service
information.
Dipstick
There are 2 level marks on
the dipstick: never exceed
level A .
In position B , top up the
level via the oil reservoir
cap, using the type of oil
suited to your engine.

A = max.

B = min.
Oil level correct
Lack of oil
Flashing indicates a lack of oil which
may damage the engine.
If the lack of oil is confi rmed by check-
ing using the dipstick, it is imperative
that the level is topped up. Oil level gauge fault
(fl ashing segments)
Check the oil level using the dipstick.
If the level is correct, the fl ashing indi-
cates an engine oil level gauge mal-
function.
Consult a PEUGEOT dealer.
The level observed on the dipstick is
only valid if the vehicle is parked on
level ground and the engine has been
off for more than 15 minutes.
After this operation, if you wish
to disconnect the battery, lock
the vehicle and wait for at least
fi ve minutes, otherwise the
zero re-set will not be registered.

1
Service indicator zero re-set
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service your-
self, the re-set procedure is as follows:

 Switch off the ignition,

 Press and hold the trip recorder
re-set button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for approx-
imately 5 seconds, after the service
information.
Dipstick
There are 2 level marks on
the dipstick: never exceed
level A .
In position B , top up the
level via the oil reservoir
cap, using the type of oil
suited to your engine.

A = max.

B = min.
Oil level correct
Lack of oil
Flashing indicates a lack of oil which
may damage the engine.
If the lack of oil is confi rmed by check-
ing using the dipstick, it is imperative
that the level is topped up. Oil level gauge fault
(fl ashing segments)
Check the oil level using the dipstick.
If the level is correct, the fl ashing indi-
cates an engine oil level gauge mal-
function.
Consult a PEUGEOT dealer.
The level observed on the dipstick is
only valid if the vehicle is parked on
level ground and the engine has been
off for more than 15 minutes.
After this operation, if you wish
to disconnect the battery, lock
the vehicle and wait for at least
fi ve minutes, otherwise the
zero re-set will not be registered.

1
30
Trip recorder zero reset
With the trip distance displayed, press
the button for a few seconds.
Distance recorder
The total distance is displayed in zone

A of the display and the trip distance
in zone B .
LIGHTING RHEOSTAT
With the lights on, press the button to
vary the intensity of the lighting of the
instruments and controls. When the
lighting reaches the minimum (or max-
imum) setting, release the button then
press it again to increase (or reduce)
the brightness.
As soon as the lighting is of the
required brightness, release the button.

1
31
TRIP COMPUTER

or
TRIP (Route): access
to the trip computer dis-
plays.
Zero reset
When the required route is displayed,
press the control for more than two
seconds. - the route
"1" tab with:

1
32
Press the "MENU" button to gain ac-
cess to the general menu.
Select the "Trip computer" or

"Vehicle diagnostics" application us-
ing the navigator, then confi rm or press
the "MODE" button until you reach the
trip computer screen, then confi rm us-
ing "OK" .
The "Trip computer" or "Vehicle diag-
nostics" menu offers various options:
- Warnings log,
- Status of the functions,
- Inputting of the distance to be trav- elled.
Warnings log
This summarises the active warning
messages, displaying them on the
multifunction display in succession.
Status of the functions
This summarises the active or inactive
status of the functions present on the
vehicle.
Distance remaining
When guidance is not activated, this
enables you to enter an approximate
distance to be travelled value.
Display on the instrument panel screen
All of the various items of trip computer
information also appear on the instru-
ment panel screen at the same time.
Distance remaining to be travelled (km or miles)
Average speed (km/h or mph)
Average consumption (l/100 or km/l or mpg)
Distance travelled (km or miles)
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).
This is the distance remaining to the
destination, either calculated at any
time by the navigation if guidance is
activated or entered by the user, mi-
nus the distance covered since the
distance was entered.
If digits are missing, dashes are dis-
played in their place.
This is the average fuel consumption
since the computer was last set to zero.
This indicates the distance travelled
since the computer was last set to zero.
Access via the general menu
"TRIP" (Route) menu

2
33
COLOUR SCREEN C
This displays the following informa-
tion, via the WIP Sound audio system
control pad:
- the time,
- the date,
- the exterior temperature (the value displayed fl ashes if there is a risk
of ice),
- the accesses check,
- the warning messages,
- the audio functions,
- the trip computer information,
-
the personalisation and confi guration
displays,
- the air conditioning parameters,
-
the front and rear parking assistance
display,
- the hands-free kit displays. Management of the displays
General menu
Press the
"MENU" button to gain ac-
cess to the general menu and select
one of the following functions:
- "Audio functions",
- "Trip computer",
- "Personalisation-Confi guration",
- "Air conditioning",
- "Telephone". "Personalisation-Confi guration"
menu
This provides access to successive
confi rmation windows.
Defi ning the vehicle parameters
This enables you to activate or de-
activate certain driving and comfort
elements:
-
"Automatic switching on of the lights", - "Follow-me-home lighting" and
"Duration",
- "Remote control action",
- "Permanent locking of the boot",
- "Directional headlamps".
Example: "Automatic switching on of
the lights"
The
"AUDIO" , "TRIP" , "CLIM" and

"TEL" buttons on the RD4 audio
equipment control pad permit display-
ing in the main window.
Example: "TRIP"
Example: "Audio functions"