2008 Peugeot 407 C Dag display
[x] Cancel search: displayPage 68 of 211
4
When the windows are closed
automatically using the remote
control, ensure that no one is
preventing them from closing
correctly.
The folding and unfolding of the ex-
terior mirrors can be deactivated by a
PEUGEOT dealer.
The complete or selective
u n l o c k i n g c a n b e c o n fi g u -
red by means of a para-
meter, via the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
boot
Press button D to unlock and open
the boot.
This action also unlocks the doors.
If the permanent locking of the boot is
activated, opening is only possible via
button D on the remote control.
When the vehicle is locked,
if unlocking is activated inad-
vertently, without a door being
opened within 30 seconds, the
vehicle will lock automatically.
T h i s f u n c t i o n c a n b e c o n fi g u -
red by means of a parame-
ter, via the multifunction
display
"Personalisation-
C o n fi g u r a t i o n " menu.
Key in ignition
A buzzer sounds on opening the driver's
door, if the key has been left in the ignition.
LOCATING YOUR VEHICLE
To locate your vehicle, if you have
locked or deadlocked it, in a car park:
press button B on the remote con-
trol, the courtesy lights come on
a n d t h e d i r e c t i o n i n d i c a t o r s fl a s h
for a few seconds.
Unlocking
Selective (if activated)
Press button C to unlock the driver's
door only.
P r e s s t h e b u t t o n a g a i n to unlock
the passenger door and the boot.
E a c h a c t i o n i s c o n fi r m e d b y r a p i d
fl a s h i n g o f t h e d i r e c t i o n i n d i c a t o r s f o r
approximately two seconds.
The exterior mirrors unfold at the same
time.
Complete
Press button C for complete un-
locking of the vehicle.
T h i s i s c o n fi r m e d b y r a p i d fl a s h i n g o f
the direction indicators for approxi-
mately two seconds.
The exterior mirrors unfold at the same
time.
Page 69 of 211
4
66
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking
button immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again.
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the igni-
tion is switched on, the code is recognised
and starting is possible.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
Take them to an approved col-
lection point.
I f t h e s y s t e m d o e s n o t f u n c -
tion correctly, the warning
light comes on on the instru-
ment panel display, accom-
panied by an audible signal
and a message on the multi-
function display.
In this case, your vehicle will not start.
Contact a PEUGEOT dealer as soon
as possible.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Page 71 of 211
4
When the windows are closed
automatically using the remote
control, ensure that no one is
preventing them from closing
correctly.
The folding and unfolding of the ex-
terior mirrors can be deactivated by a
PEUGEOT dealer.
The complete or selective
u n l o c k i n g c a n b e c o n fi g u -
red by means of a para-
meter, via the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
boot
Press button D to unlock and open
the boot.
This action also unlocks the doors.
If the permanent locking of the boot is
activated, opening is only possible via
button D on the remote control.
When the vehicle is locked,
if unlocking is activated inad-
vertently, without a door being
opened within 30 seconds, the
vehicle will lock automatically.
T h i s f u n c t i o n c a n b e c o n fi g u -
red by means of a parame-
ter, via the multifunction
display
"Personalisation-
C o n fi g u r a t i o n " menu.
Key in ignition
A buzzer sounds on opening the driver's
door, if the key has been left in the ignition.
LOCATING YOUR VEHICLE
To locate your vehicle, if you have
locked or deadlocked it, in a car park:
press button B on the remote con-
trol, the courtesy lights come on
a n d t h e d i r e c t i o n i n d i c a t o r s fl a s h
for a few seconds.
Unlocking
Selective (if activated)
Press button C to unlock the driver's
door only.
P r e s s t h e b u t t o n a g a i n to unlock
the passenger door and the boot.
E a c h a c t i o n i s c o n fi r m e d b y r a p i d
fl a s h i n g o f t h e d i r e c t i o n i n d i c a t o r s f o r
approximately two seconds.
The exterior mirrors unfold at the same
time.
Complete
Press button C for complete un-
locking of the vehicle.
T h i s i s c o n fi r m e d b y r a p i d fl a s h i n g o f
the direction indicators for approxi-
mately two seconds.
The exterior mirrors unfold at the same
time.
Page 72 of 211
4
66
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking
button immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again.
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the igni-
tion is switched on, the code is recognised
and starting is possible.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
Take them to an approved col-
lection point.
I f t h e s y s t e m d o e s n o t f u n c -
tion correctly, the warning
light comes on on the instru-
ment panel display, accom-
panied by an audible signal
and a message on the multi-
function display.
In this case, your vehicle will not start.
Contact a PEUGEOT dealer as soon
as possible.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Page 73 of 211
4
66
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking
button immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again.
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the igni-
tion is switched on, the code is recognised
and starting is possible.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
Take them to an approved col-
lection point.
I f t h e s y s t e m d o e s n o t f u n c -
tion correctly, the warning
light comes on on the instru-
ment panel display, accom-
panied by an audible signal
and a message on the multi-
function display.
In this case, your vehicle will not start.
Contact a PEUGEOT dealer as soon
as possible.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Page 82 of 211
5
74
LIGHTS STALK
Lights off
Side lights Dipped/main beam head-
lamps Lights on
With the ignition and the automatic
lights function switched off, on open-
ing the driver's door a buzzer sounds
to warn you that you have left your
lights on.
Front and rear fog lamps (ring B)
Turn ring B forwards to switch on
and backwards to switch off. The
p o s i t i o n i s c o n fi r m e d b y t h e l i g h t
on the instrument panel.
Front fog lamps (one press)
These operate with the side lights, dipped
headlamps or main beam headlamps. Rear fog lamps (two presses)
These operate with the side lights and
the front fog lamps, or with the dipped
or main beam headlamps.
Left: downwards.
Right: upwards
D i r e c t i o n i n d i c a t o r s ( fl a s h e r s )
If you forget to return the di-
rection indicator to its normal
position, the volume of the au-
dible signal will increase, if you
are driving at a speed greater
than 45 mph (70 km/h).
Parking lights *
The side lights are lit on the side the
t r a f fi c i s o n f o r a f e w h o u r s .
With the engine switched off and with-
in 45 seconds maximum, place the in-
d i c a t o r l i g h t s s t a l k o n t h e t r a f fi c s i d e
(for example: for parking on the right;
switching on of the lights on the left).
This is indicated by an audible sig-
nal and lighting of the corresponding
direction indicator on the instrument
panel for a few seconds.
If the parking lights are activat-
ed when your vehicle switches
to economy mode, they will re-
main on. However, you cannot
activate the parking lights if your ve-
hicle is already in economy mode.
Dipped/main beam change
Pull the stalk fully towards you.
* According to version.
Automatic switching on of
the lights.
In the case of vehicles which
a r e n o t fi t t e d w i t h a l i g h t s s t a l k
with the "AUTO" position,
you can deactivate or activate
the automatic lighting via the multi-
function display "Personalisation-
C o n fi g u r a t i o n " menu.
Front and rear lights (ring A)
Turn ring A to the position re-
quired
Page 83 of 211
5
75
The timed duration must also
be set, via the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
A u t o m a t i c s w i t c h i n g o n o f t h e lights
To switch the function on
or off, use the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
Activation
Deactivation When this function is activa-
ted, the indicator light on the
instrument panel comes on.
When the function is deacti-
vated, the indicator light on the
instrument panel comes on.
Cancellation:
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
M a n u a l " f o l l o w - m e - h o m e " l i g h t i n g
If the automatic switching on of the lights
is not activated, the manual "follow-me-
home" lighting can be activated.
When you leave your vehicle, the side
lights and dipped headlamps remain
on for approximately 1 minute.
Activation:
switch off the engine,
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
fl a s h t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
A u t o m a t i c " f o l l o w - m e - h o m e "
lighting
When you leave your vehicle with
the
a u t o m a t i c s w i t c h i n g o n o f t h e l i g h t s
activated , the side lights and dipped
headlamps remain on for the duration
selected when the ignition is switched
off.
To activate or deactivate this func-
tion, pass via the multifunction display
" P e r s o n a l i s a t i o n - C o n f i g u r a t i o n "
menu.
In foggy weather, the bright-
n e s s s e n s o r c a n d e t e c t s u f fi -
cient light. As a consequence,
the lights will not come on au-
tomatically.
This function is active when the vehi-
cle is supplied to the customer.
If the brightness sensor does not
f u n c t i o n c o r r e c t l y , if the system is
activated, the dipped headlamps and
the side lights come on.
Contact a PEUGEOT dealer to have
the system checked.
D a y t i m e l i g h t s *
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
The instruments and controls
(instrument panel, multifunc-
tion display, air conditioning
control panel, ...) are only lit
on switching to the automatic switch-
ing on of the lights mode or when the
lights are switched on manually. This warning light comes on
on the instrument panel.
* According to country.
This function is available di-
rectly at the lights stalk on
certain versions depending on
the type of lights stalk.
The side lights and dipped beam head-
lamps switch on automatically if the light
is poor, or during operation of the wind-
screen wipers. They switch off as soon
as the light becomes bright enough or
the windscreen wipers stop.
Page 84 of 211
5
75
The timed duration must also
be set, via the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
A u t o m a t i c s w i t c h i n g o n o f t h e lights
To switch the function on
or off, use the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
Activation
Deactivation When this function is activa-
ted, the indicator light on the
instrument panel comes on.
When the function is deacti-
vated, the indicator light on the
instrument panel comes on.
Cancellation:
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
M a n u a l " f o l l o w - m e - h o m e " l i g h t i n g
If the automatic switching on of the lights
is not activated, the manual "follow-me-
home" lighting can be activated.
When you leave your vehicle, the side
lights and dipped headlamps remain
on for approximately 1 minute.
Activation:
switch off the engine,
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
fl a s h t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
A u t o m a t i c " f o l l o w - m e - h o m e "
lighting
When you leave your vehicle with
the
a u t o m a t i c s w i t c h i n g o n o f t h e l i g h t s
activated , the side lights and dipped
headlamps remain on for the duration
selected when the ignition is switched
off.
To activate or deactivate this func-
tion, pass via the multifunction display
" P e r s o n a l i s a t i o n - C o n f i g u r a t i o n "
menu.
In foggy weather, the bright-
n e s s s e n s o r c a n d e t e c t s u f fi -
cient light. As a consequence,
the lights will not come on au-
tomatically.
This function is active when the vehi-
cle is supplied to the customer.
If the brightness sensor does not
f u n c t i o n c o r r e c t l y , if the system is
activated, the dipped headlamps and
the side lights come on.
Contact a PEUGEOT dealer to have
the system checked.
D a y t i m e l i g h t s *
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
The instruments and controls
(instrument panel, multifunc-
tion display, air conditioning
control panel, ...) are only lit
on switching to the automatic switch-
ing on of the lights mode or when the
lights are switched on manually. This warning light comes on
on the instrument panel.
* According to country.
This function is available di-
rectly at the lights stalk on
certain versions depending on
the type of lights stalk.
The side lights and dipped beam head-
lamps switch on automatically if the light
is poor, or during operation of the wind-
screen wipers. They switch off as soon
as the light becomes bright enough or
the windscreen wipers stop.